Sony DAR-X1R / HCD-X1R Service Manual ▷ View online
HCD-X1R
17
3-10. AV-103AU BOARD
3-9. ER BOARD
3
flexible flat cable (AV-ERS03)
(CN3002)
(CN3002)
2
flexible flat cable (AV-ERA02)
(CN2854)
(CN2854)
1
flexible flat cable (AV-ERV01)
(CN2853)
(CN2853)
5
screw
(B3)
(B3)
6
screw
(BV/ring)
(BV/ring)
7
ER board
4
four screws
(BVTP3
(BVTP3
×
8)
qs
flexible flat cable (AV-PR01)
(CN602)
(CN602)
qd
flexible flat cable (AV-RD02)
(CN502)
(CN502)
qf
flexible flat cable (AV-RD01)
(CN501)
(CN501)
q;
connector
(CN103)
(CN103)
qg
connector
(CN102)
(CN102)
qh
connector
(CN3)
(CN3)
qk
AV-103AU board
qa
back panel section
8
screw
(B3)
(B3)
9
screw
(BV/ring)
(BV/ring)
1
four screws
(BVTT3
(BVTT3
×
6)
qj
five screws
(BVTT3
(BVTT3
×
6)
5
screw (BVTP3
×
8)
6
four screws
(BVTP3
(BVTP3
×
10)
7
screw
(BVTP3
(BVTP3
×
8)
3
two screws
(BVTT3
(BVTT3
×
6)
4
two screws
(BVTT3
(BVTT3
×
6)
2
four washers
(LW3)
(LW3)
HCD-X1R
18
3-11. DVD DRIVE (DRW-V35A)
2
connector
(CN2)
(CN2)
harness
(POWER-DVDRW)
(POWER-DVDRW)
hard disk
clamp (L35)
clamp (L35)
harness
(SATA POWER001)
(SATA POWER001)
Note: Refer to SERVICING NOTES
“ NOTE ON POWER BLOCK”
(page 7).
(page 7).
Note: Refer to SERVICING NOTES
“ NOTE WHEN INSTALLING THE TOP PANEL
(DISCHAGING METHOD)”
(page 9).
(DISCHAGING METHOD)”
(page 9).
Note: When harness (POWER-DVDRW) and
flexible flat cable (RD-RW01), set it as shown
in the figure.
in the figure.
harness (POWER-DVDRW)
flexible flat cable
(RD-RW01)
(RD-RW01)
1 to 5 mm
Note: Bend press the clamp (L35) to down side
(chassis assy) to arrange the
harness (POWER-DVDRW)
from DVD drive (DRW-V35A) and
harness (SATA POWER001)
from hard dick as shown as figure.
harness (POWER-DVDRW)
from DVD drive (DRW-V35A) and
harness (SATA POWER001)
from hard dick as shown as figure.
1
flexible flat cable
(RD-RW01) (CN101)
(RD-RW01) (CN101)
9
two tapes (clamp)
qd
two tapes (clamp)
qa
Peel off the cushion (yokan).
qf
flexible flat cable
(RD-RW01)
(RD-RW01)
qs
tape (side)
8
clamp (L35)
qg
DVD drive
(DRW-V35A)
(DRW-V35A)
DVD drive
DRW-V35A
DRW-V35A
DVD drive
(DRW-V35A)
(DRW-V35A)
q;
harness (POWER-DVDRW)
6
Remove the DVD drive (DRW-V35A)
section in the derection of the arrow.
section in the derection of the arrow.
4
clamp (L35)
HARNESS (POWER-DVDRW/
SATA POWER001) SETTING
SATA POWER001) SETTING
HARNESS (POWER-DVDRW) AND
FLEXIBLE FLAT CABLE (RD-RW01)
SETTING
FLEXIBLE FLAT CABLE (RD-RW01)
SETTING
two tapes (clamp)
two tapes (clamp)
3
screw
(BVTP3
(BVTP3
×
10)
7
screw
(B3
(B3
×
5)
5
three screws
(BVTP3
(BVTP3
×
10)
HCD-X1R
19
3-12. POWER BLOCK
2
connector
(CN1)
(CN1)
1
connector
(CN3)
(CN3)
5
POWER block
Note: Refer to SERVICING NOTES
“ NOTE ON POWER BLOCK”
(page 7).
(page 7).
Note: Refer to SERVICING NOTES
“ NOTE ON POWER BLOCK”
(page 7).
(page 7).
4
four screws
(BVTT3
(BVTT3
×
6)
3
screw
(BVTP3
(BVTP3
×
8)
20
HCD-X1R
SECTION 4
SERVICE MODE
General
•
This is the diagnostics to locate cause of fault.
•
The diagnostics can be executed using the remote commander
(RM-ADP012) and monitor.
•
To execute the service mode connect the i LINE 1 – TV
connector (CN2852) on the ER board to the monitor.
1. Entering The Service Mode
Procedure:
1. While pressing two buttons of
Z
and
N
simultaneously,
connect the AC power cord to the power outlet.
2. The message “S” appears on the fluorescent indicator tube in
around 20 seconds and “Service Mode<<MAIN>>” menu
screen appears on the monitor screen as follows.
screen appears on the monitor screen as follows.
Service Mode<< MAIN >>
1) Version No
2) Display Color
3) Total Time
4) Error History
5) Command History
6) History Clear
7) Factory Setup
8) Device Check
9) HDD MODE
0) G-code Setting
2) Display Color
3) Total Time
4) Error History
5) Command History
6) History Clear
7) Factory Setup
8) Device Check
9) HDD MODE
0) G-code Setting
MODEL
HCX1662EC
SYSCON Version
[X.XX]
HDD Serial ID
[ XXXXXXXXXXXXXX]
SONY ID
XXXXXXXX
•
While the diagnostics is in progress, either “OK” or “NG”
appears on the monitor screen to enable the judgement whether
the respective devices or the peripheral are normal or have
any abnormality.
the respective devices or the peripheral are normal or have
any abnormality.
•
When an abnormality is detected, the diagnostics is stopped
at that moment and you can select to keep running the
diagnostics or to stop it.
diagnostics or to stop it.
2. Releasing The Service Mode
To release this mode, turn the AC power off.
3. Checking Item
Checking item
IC name
Ref. No.
EEPROM
M24C32-WMN6T (B)
IC102
VIDEO DECODER
TVP5146M2PFP
IC301
SD-RAM
HYB25DC512160CE-6
IC105
SD-RAM
HYB25DC512160CE-6
IC106
All parts are mounted on the RD-060AU board.
When NG is displayed as the result of the Device Check (Diagnostic
Test), the IC or its peripheral is defective.
Test), the IC or its peripheral is defective.
4. Screen Transition in the Service Mode
In the Service Mode, monitor screen is transition as follows.
MAIN
Version No
[1]
key
[RETURN]
key
Display Color
[2]
key
[RETURN]
key
Total Time
[3]
key
[RETURN]
key
Error History
[4]
key
[RETURN]
key
Command History
[5]
key
[RETURN]
key
History Clear
[6]
key
[RETURN]
key
Factory Setup
[7]
key
[RETURN]
key
Device Check
[8]
key
[RETURN]
key
HDD MODE
[9]
key
[RETURN]
key
G-code Setting
[0]
key
[RETURN]
key
Click on the first or last page to see other DAR-X1R / HCD-X1R service manuals if exist.