Sony DAR-X1R / HCD-X1R Service Manual ▷ View online
HCD-X1R
13
3-3. TOP PANEL SECTION
Note:
Follow the disassembly procedure in the numerical order given.
3-2. SIDE PANEL (L/R)
4
side panel L
2
Slide the
side panel L.
side panel L.
6
Slide the
side panel R.
side panel R.
3
four claws
8
side panel R
7
four claws
5
two screws
(BVTP3
(BVTP3
×
8)
1
two screws
(BVTP3
(BVTP3
×
8)
1
three screws
(BV/ring)
(BV/ring)
4
connector
(CN5101)
(CN5101)
5
top panel section
2
screw
(BVTP3
(BVTP3
×
6)
2
screw
(BVTP3
(BVTP3
×
6)
3
Note: Refer to SERVICING NOTES
“ NOTE WHEN INSTALLING
THE TOP PANEL
(DISCHARGING METHOD)”
(page 9).
THE TOP PANEL
(DISCHARGING METHOD)”
(page 9).
Note: Refer to SERVICING NOTES
“ NOTE WHEN INSTALLING
THE TOP PANEL
(DISCHARGING METHOD)”
(page 9).
THE TOP PANEL
(DISCHARGING METHOD)”
(page 9).
Note: Refer to SERVICING NOTES
“ NOTE WHEN INSTALLING
THE TOP PANEL
(DISCHARGING METHOD)”
(page 9).
THE TOP PANEL
(DISCHARGING METHOD)”
(page 9).
HCD-X1R
14
3-5. FRONT PANEL SECTION
3-4. LOADING ASSY PANEL
25 mm
20 mm
DVD drive
2
Insert the clip into a hole in the DVD drive
to unlock the tray as shown in the figure.
to unlock the tray as shown in the figure.
3
Pull the tray.
4
two claws
5
loading assy panel
1
Prepare a clip and bend it as shown in the figure.
160
°
3
front panel section
2
two claws
1
three screws
(BVTT3
(BVTT3
×
6)
HCD-X1R
15
3-6. PANEL L BOARD, PANEL R BOARD
3
PANEL L board
9
PANEL R board
1
flexible flat cable (PL-PR01)
(PANEL L board: CN5300,
PANEL R board: CN5000)
(PANEL L board: CN5300,
PANEL R board: CN5000)
4
flexible flat cable (AV-PR01)
(CN5004)
(CN5004)
5
connector
(CN5003)
(CN5003)
6
canoe clip
(small)
(small)
2
three screws
(BVTT3
(BVTT3
×
6)
7
three screws
(BVTT3
(BVTT3
×
6)
8
two screws
(BVTT3
(BVTT3
×
6)
3-7. RD-60AU BOARD
5
flexible flat cable (AV-PR01)
(CN602)
(CN602)
6
flexible flat cable (AV-PR02)
(CN603)
(CN603)
7
flexible flat cable (RD-RW01)
(CN101)
(CN101)
1
connector
(CN601)
(CN601)
qf
clamp (L35)
qa
Lift up the bracket (RD).
4
CHUKEI board
2
connector
(CN3501)
(CN3501)
8
connector
(CN203)
(CN203)
qg
bracket (RD)
qh
RD-60AU board
3
screw
(BVTT3
(BVTT3
×
6)
qd
screw
(BVTT3
(BVTT3
×
6)
9
two screws
(BVTT3
(BVTT3
×
6)
q;
two screws
(BVTT3
(BVTT3
×
6)
qs
three screws
(BVTT3
(BVTT3
×
6)
HCD-X1R
16
3-8. HARD DISK (250G)
HARNESS (SATA POWER001/
SATA SIGNAL001) SETTING
SATA SIGNAL001) SETTING
Note1:When harness (SATA POWER001),
set it as shown in the figure.
harness (SATA POWER001)
harness (SATA SIGNAL001)
Note2:When harness (SATA SIGNAL001),
set it as shown in the figure.
1
connector
(CN1)
(CN1)
9
two tapes
(clamp)
(clamp)
4
two connectors
5
two screws
(NO.6-32UNC)
(NO.6-32UNC)
5
two screws
(NO.6-32UNC)
(NO.6-32UNC)
2
two HDD
damper screws
damper screws
2
two HDD
damper screws
damper screws
3
Lift up the bracket (HDD).
bracket (HDD)
bracket (HDD)
two tapes (clamp)
three tapes (clamp)
Note: Refer to SERVICING NOTES
“ NOTE ON POWER BLOCK”
(page 7).
(page 7).
6
hard disk (250G)
8
harness
(SATA SIGNAL001)
(SATA SIGNAL001)
7
three tapes (clamp)
q;
harness
(SATA POWER001)
(SATA POWER001)
qa
bracket (HDD)
20
±
5 mm
20
±
5 mm
Click on the first or last page to see other DAR-X1R / HCD-X1R service manuals if exist.