Sony CMT-VP11 / HCD-VP11 Service Manual ▷ View online
25
6-14. IC PIN FUNCTION DESCRIPTION
• MAIN BOARD IC801 CXP83120A-041Q
(SYSTEM CONTROLLER, LCD DRIVER)
Pin No.
Pin Name
I/O
Description
1
TAPE-END
I
Tape end detect sensor input terminal “H” input when the tape end detected
2
RDS-CLK
I
Serial data reading clock signal input from the RDS decoder (IC804)
(Used for the AEP and UK models only)
(Used for the AEP and UK models only)
3
REMOCON
I
Sircs remote control signal input from the remote control receiver (IC802)
4
MOT-CON
O
Capstan/reel motor on/off control signal output terminal “H”: motor on
5
SOL-CON
O
Trigger plunger on/off control signal output terminal “H”: plunger on
6
T-MODE
I
Head position detect switch input terminal “L”: forward direction, “H”: reverse direction
7
REG-CON
O
Main system power supply on/off control signal output terminal “H”: power on
8
CD-CLK
O
Serial data transfer clock signal output to DSP/SSP on the CD block (at CD function)
9
TUNED
I
Tuning detection signal input from the tuner pack “L”: tuned
10
CD-DATA/
TU-DATA/
SDA
O
Serial data output to DSP/SSP on the CD block (at CD function)
PLL serial data output to PLL IC on the tuner pack (at tuner function)
PLL serial data output to PLL IC on the tuner pack (at tuner function)
I
2
C data output to the TDA7439 (IC301) (all functions)
11
CD-SQCK
O
Subcode Q data reading clock signal output to DSP on the CD block (at CD function)
12
CD-SQSO/
RDS-DATA
I
Subcode Q data input from DSP on the CD block (at CD function)
RDS serial data input from the RDS decoder (IC804) (at tuner function)
(RDS decoder: used for the AEP and UK models only)
RDS serial data input from the RDS decoder (IC804) (at tuner function)
(RDS decoder: used for the AEP and UK models only)
13
TRAY-OPEN
O
Motor drive signal output to the disc tray open/close motor driver (IC309) “H” active *1
14
CD-MUTE
O
Muting on/off control signal output to the CD block “H”: muting on
15
TRAY-CLOSE
O
Motor drive signal output to the disc tray open/close motor driver (IC309) “H” active *1
16
CD-SENSE1
I
Internal status detection monitor input from CD block
(for FZC, DFCT1, TZC, etc.) (at CD function)
(for FZC, DFCT1, TZC, etc.) (at CD function)
17
CD-XRST
O
Reset signal output to the CD block “L”: reset
18
CD-SENSE2/
TU-COUNT
I
Internal status detection monitor input from the CD block
(for MIRR, DFCT2, etc.) (at CD function)
PLL count data input from PLL IC on the tuner pack (at tuner function)
(for MIRR, DFCT2, etc.) (at CD function)
PLL count data input from PLL IC on the tuner pack (at tuner function)
19
CD-LATCH/
TU-CE
O
Serial data latch pulse output to DSP on the CD block (at CD function)
PLL serial chip enable signal output to PLL IC on the tuner pack (at tuner function)
PLL serial chip enable signal output to PLL IC on the tuner pack (at tuner function)
20
JOG-B
I
Jog dial pulse input from the rotary encoder (RV801 VOLUME) (B phase input)
21
JOG-A
I
Jog dial pulse input from the rotary encoder (RV801 VOLUME) (A phase input)
22
AMP-MUTE
O
Muting on/off control signal output to the power amplifier (IC101, 201)
“H”: muting on
“H”: muting on
23
AMP-STBY
O
Standby on/off control signal output to the power amplifier (IC101, 201)
“L”: standby mode
“L”: standby mode
24
VIDEO-ON
O
VIDEO/MD function control signal output terminal
“H”: VIDEO/MD (“L” output when other functions)
“H”: VIDEO/MD (“L” output when other functions)
25
TU-ON
O
Power supply on/off control signal output of the tuner pack (+10V)
LED drive signal output of the TUNER indicator (D855) “H”: tuner power on (LED on)
LED drive signal output of the TUNER indicator (D855) “H”: tuner power on (LED on)
26
D.S.G.
O
LED drive signal output of the DSG (Dynamic Sound Generator) indicator (D856)
“H”: LED on
“H”: LED on
27
CD-SYNC
O
LED drive signal output of the CD SYNC indicator (D857) “H”: LED on
28
SCK
O
Serial data transfer clock signal output to the TDA7439 (IC301)
29
TU-CLK
O
PLL serial data transfer clock signal output to PLL IC on the tuner pack (at tuner function)
*1 Disc tray open/close motor control
Stop
Table In
Table Out
Brake
TRAY-OPEN (pin
)
“L”
“L”
“H”
“H”
TRAY-CLOSE (pin
)
“L”
“H”
“L”
“H”
Terminal
Mode
qd
qg
26
Pin No.
Pin Name
I/O
Description
30
RDS-ON
O
Power supply on/off control signal output of the tuner pack (+7.5V) and RDS decoder (IC804)
(RDS decoder: used for the AEP and UK models only)
LED drive signal output of the TUNER indicator (D855) “H”: tuner power on (LED on)
(RDS decoder: used for the AEP and UK models only)
LED drive signal output of the TUNER indicator (D855) “H”: tuner power on (LED on)
31
HP-CHK
I
Headphone check detection signal input terminal
32
TC-SW
I
Half detect (side A and B) switch and cassette in detect switch input terminal (A/D input)
33
TRAY-SW
I
Disc tray position detect switch (S901, 902) input terminal (A/D input)
“L”: close position, “M”: open position, “H”: moving
“L”: close position, “M”: open position, “H”: moving
34
KEY3
I
Key input terminal (A/D input) S817 to S822, S824 and S825 (STANDBY I/
u, CD, TUNER,
TAPE, MD/VIDEO, DSG, TUNER BAND, CD SYNC keys input)
35
KEY2
I
Key input terminal (A/D input) S801 to S808 (TUNING MODE, CD
^/p/+/=, PLAY
MODE, REPEAT, CD EJECT
6 keys input)
36
KEY1
I
Key input terminal (A/D input)
S809 to S816 (TAPE
S809 to S816 (TAPE
9 (/p/)/0/P, REC r, TUNING +/– keys input)
37
SIMUKE
I
Destination setting terminal (A/D input)
38
RESET
I
System reset signal input from the reset signal generator (IC803) “L”: reset
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
39
EXTAL1
I
Main system clock input terminal (4.19 MHz)
40
XTAL1
O
Main system clock output terminal (4.19 MHz)
41
VSS
—
Ground terminal
42
XTAL2
O
Sub system clock output terminal (500 kHz) Not used (open)
43
EXTAL2
I
Sub system clock input terminal (500 kHz) Not used (fixed at “L”)
44
AVREF
I
Reference voltage (+5V) input terminal (for A/D conversion)
45
AVSS
—
Ground terminal (for A/D conversion)
46
VL
O
Liquid crystal display bias on/off control signal output terminal
47 to 49
VLC3 to VLC1
—
Power supply terminal for the liquid crystal display bias
50 to 53
COM0 to COM3
O
Common drive signal output to the liquid crystal display (LCD801)
54 to 85
SEG0 to SEG31
O
Segment drive signal output to the liquid crystal display (LCD801)
86
REC-BIAS
O
Recording bias on/off selection signal output to the HA12203NT (IC352)
“L”: bias on, “H”: bias off
“L”: bias on, “H”: bias off
87
REC-MUTE
O
Recording muting on/off selection signal output to the HA12203NT (IC352)
“L”: muting on, “H”: muting off
“L”: muting on, “H”: muting off
88
DOLBY
O
Dolby NR on/off selection signal output to the HA12203NT (IC352)
“L”: dolby on, “H”: dolby off
“L”: dolby on, “H”: dolby off
89
VDD
—
Power supply terminal (+5V)
90
NC
—
Connected to power supply (+5V)
91
VSS
—
Ground terminal
92
TX
O
Sub system clock output terminal (32.768 kHz)
93
TEX
I
Sub system clock input terminal (32.768 kHz)
94
CD-ON
O
Power supply on/off control signal output of the CD block (+5V)
LED drive signal output of the CD indicator (D852) “H”: CD power on (LED on)
LED drive signal output of the CD indicator (D852) “H”: CD power on (LED on)
95
REC/PB
O
Recording/playback selection signal output to the BA3126N (IC350) and HA12203NT (IC352)
“L”: playback mode, “H”: recording mode
“L”: playback mode, “H”: recording mode
96
L-MUTE
O
Line muting on/off selection signal output to the HA12203NT (IC352)
“L”: muting on, “H”: muting off
“L”: muting on, “H”: muting off
97
LINE OUT-MUTE
O
Muting on/off control signal output terminal “H”: muting on
98
TC-ON
O
Power supply on/off control signal output of the cassette holder back light
LED drive signal output of the TAPE indicator (D854) “H”: back light on (LED on)
LED drive signal output of the TAPE indicator (D854) “H”: back light on (LED on)
99
WP
I
Wakeup control signal input terminal
100
CD-SCOR
I
Subcode sync (S0+S1) detection signal input from DSP on the CD block (at CD function)
SECTION 7
EXPLODED VIEWS
27
NOTE:
•
-XX, -X mean standardized parts, so they may
have some differences from the original one.
have some differences from the original one.
•
Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering these
items.
are seldom required for routine service. Some
delay should be anticipated when ordering these
items.
•
The mechanical parts with no reference number
in the exploded views are not supplied.
in the exploded views are not supplied.
•
Hardware (# mark) list and accessories and
packing materials are given in the last of this
parts list.
packing materials are given in the last of this
parts list.
•
Abbreviation
SP
SP
: Singapore model.
MY
: Malaysia model.
HK
: Hong Kong model.
TH
: Thai model.
EA
: Saudi Arabia model.
The components identified by mark
0
or
dotted line with mark
0
are critical for safety.
Replace only with part number specified.
Ref. No.
Part No.
Description
Remarks
#1
#1
Front panel
secrtion
secrtion
#2
#2
not
supplied
supplied
1
#1
#1
3
2
#1
Chassis section
3
7-1. COVER, TAPE MECHANISM DECK SECTION
1
1-772-623-11 DECK,MECHANICAL (TAPE DECK BLOCK)
2
4-217-341-31 COVER(UPPER)
3
4-221-580-01 SCREW, CASE
28
Ref. No.
Part No.
Description
Remarks
Ref. No.
Part No.
Description
Remarks
supplied
with RV801
with RV801
#1
#1
#1
68
51
71
52
69
53
55
56
58
59
61
#3
57
67
63
64
60
64
not
supplied
supplied
64
64
65
66
62
not
supplied
supplied
not
supplied
supplied
7-2. FRONT PANEL SECTION
51
X-4952-336-1 KNOB ASSY
52
X-4952-749-1 PANEL SUB ASSY, FRONT
53
4-227-956-01 WINDOW (CASSETTE)
55
4-217-316-11 LID,CASSETTE
56
1-678-282-11 LCD BOARD
57
4-217-319-01 PLATE, LCD LIGHT
58
4-217-317-02 HOLDER (CASSETTE) (TH)
58
4-229-876-01 HOLDER (CASSETTE)(SP,MY,EA,HK)
59
4-229-069-01 SPRING, CASSETTE
60
1-792-413-11 CABLE, FLEXIBLE FLAT (18 CORE)
61
1-792-412-11 CABLE, FLEXIBLE FLAT (20 CORE)
62
4-217-320-01 PLATE, BACK LIGHT
63
X-4951-937-1 LOCK(EJECT) ASSY
64
4-931-757-31 SCREW(DIA.2.6X8)(IT3B),TAPPING
65
A-4428-925-A CONTROL BOARD, COMPLETE
66
3-351-377-11 GEAR, DAMPER
67
4-218-204-01 FOOT(FRONT)
68
1-677-147-21 HEADPHONE BOARD
69
4-227-282-11 KNOB(BASS)
71
4-221-075-01 KNOB(MIC VOL)
Click on the first or last page to see other CMT-VP11 / HCD-VP11 service manuals if exist.