Sony CMT-SE1 / HCD-SE1 Service Manual ▷ View online
5
HCD-SE1
Remote control
BASS +/– w;
CD 7
CLEAR 6
CLOCK/TIMER SELECT 2
CLEAR 6
CLOCK/TIMER SELECT 2
CLOCK/TIMER SET 3
DBFB ql
DISPLAY wf
DBFB ql
DISPLAY wf
ENTER 5
FM MODE 9
MD (TAPE) wd
FM MODE 9
MD (TAPE) wd
PLAY MODE qk
PRESET +/– qj
PRESET +/– qj
REPEAT qh
SLEEP 1
SLEEP 1
TREBLE +/– qd
TUNER/BAND 8
TUNER MEMORY q;
TUNER/BAND 8
TUNER MEMORY q;
TUNING MODE ws
TUNING +/– qf
VOL +/– qg
TUNING +/– qf
VOL +/– qg
?/1 (power) 4
N (play) wa
x (stop) qs
./> (go back/go forward)
N (play) wa
x (stop) qs
./> (go back/go forward)
qj
m/M (rewind/fast forward)
qf
X (pause)
qa
ALPHABETICAL ORDER
A – Q
R – Z
BUTTON DESCRIPTIONS
1
Press
?/1
to turn on the system.
2
Press CLOCK/TIMER SET.
3
Press
.
or
>
repeatedly to set the
hour.
4
Press ENTER.
5
Press
.
or
>
repeatedly to set the
minute.
6
Press ENTER.
The clock starts working.
To adjust the clock
1
Press CLOCK/TIMER SET.
2
Press
.
or
>
until “CLOCK SET?”
appears, then press ENTER.
3
Do the same procedures as step 3 to 6
above.
above.
Note
The clock is not displayed in Power Saving Mode.
Tip
When you adjust the clock while the system is off, do
the same procedures as step 2 to 6 above.
the same procedures as step 2 to 6 above.
Setting the clock
HCD-SE1
6
• This set can be disassembled in the order shown below.
SECTION 2
DISASSEMBLY
BASE UNIT
CHASSIS (TOP)
CASE
CD MECHANISM DECK
(CDM80B-K6BD44S)
(CDM80B-K6BD44S)
FRONT PANEL
LID (CD) ASSY
FRONT PANEL ASSY SECTION
CD MECHANISM BLOCK SECTION
SWITCHING REGULATOR
AMP BOARD,
SUB TRANS BOARD
SUB TRANS BOARD
DISC STOP LEVER,
DISC SENSOR LEVER
DISC SENSOR LEVER
JACK BOARD
DRIVER
BOARD
BD BOARD
BU SECTION
LEVER (BU BLOCK)
CLOSE LEVER
DIR LEVER,
GEAR (IDL-B)
GEAR (IDL-B)
GEAR (IDL-C)
SET
LEVER (LOADING R / L)
Ver 1.1 2003.11
HCD-SE1
7
4
case
1
case screw
2
case screw
3
two screws (BVTP 3
×
6)
4
two claws
3
two claws
7
front panel assy sectiom
6
connector
(CN201)
5
wire (flat type) (19core)
(CN503)
1
two screws
(BVTP 3
×
8)
2
screw
(BVTP 3
×
8)
Note:
Follow the disassembly procedure in the numerical order given.
2-1. CASE
2-2. FRONT PANEL ASSY SECTION
HCD-SE1
8
3
two screws
(BVTP 3
×
8)
9
two screws
(BVTP 3
×
8)
5
two screws
(BTP 2.6
×
6)
qa
two screws
(BVTT 4
×
8)
8
screw
(P 3
×
5)
4
connector
(CN510)
7
connector
(CN931)
2
connector
(CN993)
0
JACK board
qs
DC fan
qd
back panel
6
tuner unit
1
wire (flat type) (11core)
qs
two claws
qd
front panel (ALMI-CD) assy
1
knob (VOL)
7
knob (LEVER)
8
PANEL board
0
H/P board
qf
front panel assy
qa
bracket (HP)
2
wire (flat type) (19core)
(CN801)
6
screw
(BVTP 3
×
6)
9
screw
(BVTP 3
×
8)
5
screw
(BVTP 3
×
6)
4
three screws
(BVTP 3
×
8)
3
eight screws
(BVTP 3
×
8)
2-3. FRONT PANEL
2-4. JACK BOARD
Click on the first or last page to see other CMT-SE1 / HCD-SE1 service manuals if exist.