DOWNLOAD Sony CMT-M9 / HCD-D11 / HCD-T11 Service Manual ↓ Size: 420.66 KB | Pages: 30 in PDF or view online for FREE

– 9 –

1

two screws
(BV3 

×

 8)

3

CD mechanism section

2

two hooks

1

screw (BV3 

×

 8)

2

holder (MG) ass’y

1

screw (BV3 

×

 8)

3

Pull the disc table

– 10 –

4

Remove the optical pick-up
in the direction of the arrow 

C

.

3

wire (flat type) (16 core)
(CNU101)

C

2

Remove the sled shaft in the
direction of the arrow 

B

.

B

A

1

Move the claw in the
direction of the arrow 

A

.

– 11 –

As a front-end (TB101) is difficult to repair if faulty, replace it with
new one.
Please note, however, that the following adjustments are possible:

Note: FM Tuned Level Adjustment Should be performed after this

AM Tuned Level Adjustment.

Setting:
Band: AM or MW

Procedure:
Turn the set to 98 MHz.

set

FM RF SSG

+
–

level meter

J101 (OUTPUT)

FM ANTENNA
terminal (TM101)

Carrier frequency: 98 MHz
Output level: 1 mV (60 dB)
Modulation:
   Main (1 kHz): 33.75 kHz dev. (45%)
   Sub (1 kHz): 33.75 kHz dev. (45%)
   Pilot (19 kHz): 7.5 kHz dev. (10%)

47 k

Ω

FM stereo

VTVM

VTVM

signal generator

connection

reading (dB)

output channel

L-CH

L-CH

A

B

R-CH

L-CH

Adjust  SEP (W)  for

minimum reading.

R-CH

R-CH

C

D

L-CH

R-CH

Adjust   SEP (W)   for

minimum reading.

L-CH Stereo separation: A – B
R-CH Stereo separation: C – D

The separations of both channels should be equal.

Adjustment Location: Main board (TB101)  (See page 13)

Procedure:
1. Set AM RF SSG output level to 76 dBµ  so that the input level

becomes 50 dBµ .

2. Tune the set to 999 kHz (at 9 kHz step) or 1,050 kHz (at 10 kHz

step).

3. Adjust  AM TUN (W)  so that the TUNED light up.

Adjustment Location: Main board (TB101)  (See page 13)

Setting:
Band: FM

AM RF  SSG

loop antenna

set

loop antenna of 

accessories

60 cm

AM ANTENNA

terminal (TM101)

Carrier frequency: 999 kHz (at 9 kHz step)

Modulation: 400 Hz  30%
Output level: 6.3 mV (76 dB

µ

)

1,050 kHz (at 10 kHz step)

Procedure:
1. Supply a 17.8 µV (25 dBµ ) 98 MHz signal to the ANTENNA

terminal.

2. Tune the set to 98 MHz.
3. Adjust   FM TUN (W)   so that the TUNED light up.

Adjustment Location: Main board (TB101) (See page 13)

set

FM ANTENNA terminal (TM101)

FM RF SSG

Carrier frequency: 98 MHz
Modulation: 1 kHz, 75 kHz deviation
Output level: 17.8 

µ

V (25 dB

µ

)

– 12 –

Note:
1. CD Block basically constructed to operate without adjustment.

Therefore, check each item in order given.

2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated.
3. Use the oscilloscope with more than 10M

Ω

 impedance.

4. Clean an object lens by an applicator with neutral detergent when

the signal level is low than specified value with the following
checks.

This adjustment is to be done when the optical block is replaced.

+
–

BD board

TP (RF)

TP (VC)

oscilloscope

(DC range)

1. Connect oscilloscope to test point TP (VC) and TP (RF) on BD

board.

2. Ground display board IC701 pin @¢ with the lead wire.
3. Turned power switch ON. (Stop mode)
4. Put disc (YEDS-18) in and press the 

^ button.

5. Press the 

^ button again. (Tracking servo ON)

6. Adjust RV101 so that the oscilloscope waveform is as shown in

the figure below (eye pattern).
A good eye pattern means that the diamond shape (≈) in the
center of the waveform can be clearly distinguished.

7. Remove the lead wire connected in step2.

•

 RF signal reference waveform (eye pattern)

VOLT/DIV: 200 mV
TIME/DIV: 500 ns

level:
1.3 

±

 0.3Vp-p

When observing the eye pattern, set the oscilloscope for AC
range and raise vertical sensitivity.

+
–

BD board

TP (FEO)

TP (VC)

oscilloscope

Procedure:
1. Connect oscilloscope to test point TP (VC) and TP (FEO) on

BD board.

2. Connect between test point TP (FOK) and Ground by lead wire.
3. Turned Power switch on.
4. Put disc (YEDS-18) in and turned Power switch on again and

actuate the focus search. (actuate the focus search when disc
table is moving in and out.)

5. Check the oscilloscope waveform (S-curve) is symmetrical be-

tween A and B. And confirm peak to peak level within 2.4 ± 0.7
Vp-p.

A

B

symmetry

within 2.4 

±

 0.7 Vp-p

6. After check, remove the lead wire connected in step 2.
Note:

•

Try to measure several times to make sure that the ratio of
A:B or B:A is more than 10:7.

•

Take sweep time as long as possible and light up the bright-
ness to obtain best waveform.

S-curve waveform

+
–

BD board

TP (RF)

TP (VC)

oscilloscope

Procedure:
1. Connect oscilloscope to test point TP (VC) and TP (RF) on BD

board.

2. Turned Power switch on.
3. Put disc (YEDS-18) in and press the 

^ button.

4. Confirm that oscilloscope waveform is clear and check RF sig-

nal level is correct or not.

Note: Clear RF signal waveform means that the shape “≈” can be

clearly distinguished at the center of the waveform.

RF signal waveform

+
–

BD board

TP (TEO)

TP (VC)

oscilloscope

(DC range)

Procedure:
1. Ground display board IC701 pin @¢ with the lead wire.
2. Connect oscilloscope to test point TP (TEO) on BD board.
3. Turned Power switch on.
4. Put disc (YEDS-18) in and press the 

^ button.

5. Confirm that the oscilloscope waveform is symmetrical on the

top and bottom in relation to 0V, and check this level.

VOLT/DIV: 200 mV
TIME/DIV: 500 ns

level:
1.3 

±

 0.3Vp-p