DOWNLOAD Sony CMT-F3MD / HCD-F3MD Service Manual ↓ Size: 10.5 MB | Pages: 96 in PDF or view online for FREE

17

You  can use the supplied remote to control the
system.

You cannot perform the following operations with the
remote;
— TUNING MODE setting for the tuner
— STEREO/MONO setting for the tuner
— Removing discs
— Recording on the MD
— One Touch Play

1

2

3

4

1 ?

1

2

Press to switch the sound source.

Each time you press this button, the sound source

changes as follows;

t 

CD

t 

TUNER 

 

TAPE 

T

MD 

T

Press to select the tuner for the sound source, or

to select the FM or AM band.

3 N

X

x

T

t

m

M

Press to label a CD, MD and preset station, or to

set the clock. (pages 5, 18, 35, 45)

.

>

4

Press to adjust the volume.

Press to set Programme Play, or to label a CD,

MD and preset station.

Press to set the clock, Programme Play and to

label a CD, MD and preset station, or to enter the

settings in “Edit Menu” or “Setup Menu”.

Press to show the various information. (pages 17

and 23)

You  must set the time beforehand to use the timer
functions.

CURSOR

T

DISP

4,6

3,5

2

1

4

3,5

Turn on the system.

Press CLOCK/TIMER SET.

The clock appears and the hour indication
flashes.

Press . or > to set the hour.

Press ENTER/YES or CURSORt .

The minute indication flashes.

9

Press to reinforce the bass sound. (page 44)

0

Press to display the disc title or track title

scrolling. (pages 19, 23, 36)

qa

Press to cancel the selection. (pages 16, 18, 21,

35, 45)

8

9

0

5

6

qa

7

5

Press to set Sleep Timer. (page 46)

6

Press to select normal play, Shuffle Play or

Programme Play. (pages 15, 16, 21, 25)

Press to play a track or all the tracks repeatedly

(pages 15 and 20).

Press to select the type of the preset equalizer.

(page 44)

7

Press to display the text input screen and to select

the type of characters to be input. (pages 19, 35,

45)

Press to enter a space directly when labelling a

CD, MD and preset stion. (pages 19, 36, 46)

8

Press to check timer settings, or to set the timer

on/off. (pages 48 and 49)

Press to set the clock and timer functions. (pages

5, 47, 48)

Press . or > to set the minute.

Press ENTER/YES.

The clock starts.

Press CURSORT or t repeatedly until the
incorrect item flashes, then set it again.

You  can change the preset time while the system
is off.

Press DISP to display the clock.

Press CLOCK/TIMER SET.

Repeat steps 3 to 6 of “Setting the time”.

The upper dot of the colon flashes for the first 30
seconds, and the lower dot flashes for the last 30
seconds of each minute.

18

 Follow the disassembly procedure in the numerical order given.

2

case

1

two screws 
(case3 TP2)

1

two screws
(case3 TP2)

3

Remove the cord.

8

screw
(BVTP2.6 

×

 8)

8

screw (BVTP2.6 

×

 8)

5

screw (BVTT3 

×

 6)

4

three screws
(BVTT3 

×

 6)

q;

front panel section

6

claw

6

claw

6

claw

1

wire (flat type)
(29 core) (CN11)

1

wire (flat type) (25 core)
(CN107)

2

ground wire

7

9

MD mechanism deck section

BACK PANEL ASS’Y
(Page 22)

19

2

four step screws
(BVTPWH M3)

1

connector (CN601)

4

wire (flat type) (23 core)
(CN103)

4

wire (flat type) (21 core)
(CN102)

6

MD mechanism deck
(MDM-5GA)

3

5

bracket (MDM)

7

slider (cam)

3

bracket (guide L)

1

two screws
(DIA2.6)

4

leaf spring
(electrostatic)

2

ground 
wire

When attaching the slider (cam), 
this part of the over write head 
should be inside arrow 

A

.

6

bracket (guide R)

5

two screws
(DIA.2.6)

Set the shaft of lever 
(O/C) to be at the position 
in the figure.

• 

NOTE FOR INSTALLATION 
OF SLIDER (CAM)

A

Set the shaft of cam gear to be
at the position in the figure.

20

7

base unit (MBU-5A)

1

Remove two solders 
of spindle motor leads 
(M901).

2

Remove two solders 
of sled motor leads (M902).

CN103

CN102

3

three screws
(DIA.2.6)

4

screw (M1.7)

6

BD (MD) 
board

5

two flexible boards
(CN101, 104)

2

screw (P1.7 

× 

6)

1

flexible board
(CN104)

3

over write head
(HR901)