Sony CMT-F3MD / HCD-F3MD Service Manual ▷ View online
5
SECTION 1
SERVICING NOTES
The laser diode in the optical pick-up block may suffer electro-
static break-down because of the potential difference generated
by the charged electrostatic load, etc. on clothing and the human
body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
static break-down because of the potential difference generated
by the charged electrostatic load, etc. on clothing and the human
body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
For CD
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused
on the disc reflective surface by the objective lens in the optical
pick-up block. Therefore, when checking the laser diode emis-
sion, observe from more than 30 cm away from the objective lens.
on the disc reflective surface by the objective lens in the optical
pick-up block. Therefore, when checking the laser diode emis-
sion, observe from more than 30 cm away from the objective lens.
LASER DIODE AND FOCUS SEARCH OPERATION
CHECK
CHECK
Carry out the “S curve check” in “CD section adjustment” and
check that the S curve waveforms is output three times.
check that the S curve waveforms is output three times.
For MD
NOTES ON LASER DIODE EMISSION CHECK
Never look into the laser diode emission from right above when
checking it for adjustment. It is feared that you will lose your sight.
checking it for adjustment. It is feared that you will lose your sight.
CLEANING OBJECTIVE LENS OF OPTICAL PICK-UP
• In cleaning the objective lens of optical pick-up, be sure the
following below.
1. In cleaning the lens, do not apply an excessive force.
As the optical pick-up is vulnerable, application of excessive
force could damage the lens holder.
force could damage the lens holder.
2. In cleaning, do not use a cleaner other than exclusive cleaning
liquid (KK-91 or isopropyl alcohol).
3. Wipe the objective lens spirally from center toward outside.
(See Figure A)
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
BLOCK OR BASE UNIT
MODEL IDENTIFICATION
— Back panel —
(Figure A)
4. Eject the disk, if loaded.
5. Disconnect the power cord from the socket to shut off the power
5. Disconnect the power cord from the socket to shut off the power
supply.
6. When cleaning the objective lens of optical pick-up in CD,
refer to “HOLDER (BU) ASS’Y” on page 24 for removing
HOLDER (BU) ASS’Y.
HOLDER (BU) ASS’Y.
PART No.
Model
Part No.
Hong Kong model
4-229-548-1[]
Korean model
4-232-128-0[]
Taiwan model
4-232-129-0[]
6
DRAWING OUT THE TRAY WHEN THE POWER IS OFF
CLEANING THE OPTICAL PICK-UP (CD PLAYER)
tray (CDM)
Move the cam block in the direction
of arrow
of arrow
A
with a finger.
A
CD mechanism deck
floating screw
(PTPWH M2.6)
(PTPWH M2.6)
optical pick-up block
Clean the lens block
with a cotton bud.
with a cotton bud.
7
SERVICE POSITION OF THE MD MECHANISM
DECK
DECK
SERVICE POSITION OF THE CD MECHANISM
DECK
DECK
MD mechanism deck
CD mechanism deck
SERVICE POSITION OF THE POWER BOARD
MAIN board
POWER board
CN993
CN802
Extension cable (4P)
(J-2501-042-A)
(J-2501-042-A)
Extension cable (3P)
(J-2501-045-A)
(J-2501-045-A)
AMP board
8
MC COLD RESET
• The cold reset clears all data including preset data stored in the RAM to initial conditions. Execute this mode when returning the set to
the customer.
Procedure:
1. Press the
1. Press the
I/1
button to turn the power on.
2. While pressing the
[PLAY MODE/TUNING MODE]
and
s
(CD) buttons, press the
I/1
button.
3. The set is reset, and displays “COLD RESET”, then becomes standby status.
MC HOT RESET
•
This mode resets the set with the preset data kept stored in the memory. The hot reset mode function is same as if the power cord is plugged
in and out.
in and out.
Procedure:
1. Press the
1. Press the
I/1
button to turn the power on.
2. While pressing the
[PLAY MODE/TUNING MODE]
and
HS
(CD) buttons, press the
I/1
button.
3. The set is reset, and becomes standby state.
LED/FLUORESCENT INDICATOR TUBE AND KEY TEST
Procedure:
1. Press the
1. Press the
I/1
button to turn the power on.
2. While pressing the
[PLAY MODE/TUNING MODE]
and
A
(CD) buttons, press the
I/1
button.
3. LEDs and fluorescent indicator tube are all turned on.
4. Press the
4. Press the
HS
(MD) button to enter the key test mode, and display “Key0 Vol0”.
5. Each time a button is pressed, “Key” value increases. However, once a button is pressed, it is no longer taken into account.
“Vol” value increases like 0, 1, 2 ... if turn the
[VOLUME]
knob clockwise, or it decreases like 9, 8, 7 ... if turn the
[VOLUME]
knob
counterclockwise.
6. To release from this mode, press three buttons in the same manner as step 2, or disconnect the power cord.
Note:
l m
and
M L
buttons are no longer taken into account, if it pressed within for a second.
CHANGE-OVER THE AM TUNING INTERVAL
• The AM tuning interval can be changed over 9 kHz or 10 kHz.
Procedure:
1. Press the
Procedure:
1. Press the
I/1
button to turn the power on.
2. Press the
[FUNCTION]
button to set the TUNER function, and press the
[TUNER/BAND]
button to select the band “AM”.
3. Press the
I/1
button to turn the power off.
4. When the power off, press the
I/1
button while pressing the
[PLAY MODE/TUNING MODE]
button, and the display of fluorescent
indicator tube changes to “AM 9k STEP” or “AM 10k STEP”, and thus the tuning interval is changed over.
Click on the first or last page to see other CMT-F3MD / HCD-F3MD service manuals if exist.