Sony CMT-CP33MD / HCD-CP33 / HCD-CP33K Service Manual ▷ View online
9
Reading the Display:
Convert the hexadecimal display into binary display. If more than two causes, they will be added.
Convert the hexadecimal display into binary display. If more than two causes, they will be added.
Example
When 42 is displayed:
Higher bit : 4 = 0100
n b6
Lower bit : 2 = 0010
n b1
In this case, the retry cause is combined of “CLV unlock” and “ader5”.
When A2 is displayed:
Higher bit : A = 1010
n b7+b5
Lower bit : 2 = 0010
n b2
The retry cause in this case is combined of “access fault”, “IVR rec error”, and “ader5”.
Retry Cause Display Mode
• In this test mode, the causes for retry of the unit during recording can be displayed on the fluorescent indicator tube. During playback,
the “track mode” for obtaining track information will be set.
This is useful for locating the faulty part of the unit.
This is useful for locating the faulty part of the unit.
• The following will be displayed :
During recording and stop
: Retry cause, number of retries, and number of retry errors.
During playback
: Information such as type of disc played, part played, copyright.
These are displayed in hexadecimal.
Precedure:
1. Load a recordable disc whose contents can be erased into the unit.
2. Press the FUNCTION button and set the function to “MD”.
3. Press the MENU/NO button. When “Edit/Menu” is displayed on the fluorescent indicator tube, rotate the AMS dial to display “All
1. Load a recordable disc whose contents can be erased into the unit.
2. Press the FUNCTION button and set the function to “MD”.
3. Press the MENU/NO button. When “Edit/Menu” is displayed on the fluorescent indicator tube, rotate the AMS dial to display “All
Erase?”.
4. Press the ENTER/YES button.
5. “All Erase??” is displayed on the fluorescent indicator tube.
6. Press the ENTER/YES button to display “Complete!!”, and press the x button immediately. Wait for about 10 seconds while pressing
5. “All Erase??” is displayed on the fluorescent indicator tube.
6. Press the ENTER/YES button to display “Complete!!”, and press the x button immediately. Wait for about 10 seconds while pressing
the button.
7. When the “TOC” displayed on the fluorescent display tube goes off, release the x button.
8. Press the MD REC z button to start recording. Then press the MD u button and start recording.
9. To check the “track mode”, press the MD u button to start play.
10. To exit the test mode, press the ?
8. Press the MD REC z button to start recording. Then press the MD u button and start recording.
9. To check the “track mode”, press the MD u button to start play.
10. To exit the test mode, press the ?
/1 button, and turn OFF the power. When “TOC” disappears, disconnect the power plug from the
outlet. If the test mode cannot be exited, refer to “Forced Reset” on page 8.
} Address (Physical address on disc)
Fig. 1 Reading the Test Mode Display
(During recording and stop)
(During recording and stop)
RTs@@c##c**
Fluorescent display tube display
@@ : Cause of retry
##
##
: Number of retries
**
: Number of retry errors
Fig. 2 Reading the Test Mode Display
(During playback)
(During playback)
@@####**$$
Fluorescent display tube display
@@ : Parts No. (name of area named on TOC)
##
##
: Cluster
**
: Sector
$$
: Track mode (Track information such as copyright
information of each part)
Reading the Retry Cause Display
Hexadecimal
Bit
Binary
8
4
2
1
8
4
2
1
b7 b6 b5 b4 b3 b2 b1 b0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
1
0
0
0
0
0
0
1
0
0
0
0
0
0
1
0
0
0
0
0
0
1
0
0
0
0
0
0
1
0
0
0
0
0
0
1
0
0
0
0
0
0
1
0
0
0
0
0
0
0
Higher Bits
Lower Bits
Hexa-
decimal
Cause of Retry
Occurring conditions
shock
ader5
Discontinuous adress
DIN unlock
FCS incorrect
IVR rec error
CLV unlock
Access fault
When track jump (shock) is detected
When ADER was counted more than five times
continuously
When ADIP address is not continuous
When DIN unlock is detected
When not in focus
When ABCD signal level exceeds the specified range
When CLV is unlocked
When access operation is not performed normally
01
02
04
08
10
20
40
80
10
Hexadecimal
Bit
Binary
Higher Bits
Lower Bits
8
4
2
1
8
4
2
1
b7 b6 b5 b4 b3 b2 b1 b0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
1
0
0
0
0
0
0
1
0
0
0
0
0
0
1
0
0
0
0
0
0
1
0
0
0
0
0
0
1
0
0
0
0
0
0
1
0
0
0
0
0
0
1
0
0
0
0
0
0
0
Hexa-
decimal
Details
01
02
04
08
10
20
40
80
Emphasis OFF
Monaural
This is 2-bit display. Normally 01.
01:Normal audio. Others:Invalid
Audio (Normal)
Original
Copyright
Write prohibited
When 0
When 1
Emphasis ON
Stereo
Invalid
Digital copy
No copyright
Write allowed
Reading the Display:
Convert the hexadecimal display into binary display. If more than two causes, they will be added.
Convert the hexadecimal display into binary display. If more than two causes, they will be added.
Example When 84 is displayed:
Higher bit : 8 = 1000
n b7
Lower bit : 4 = 0100
n b2
In this case, as b2 and b7 are 1 and others are 0, it can be determined that the retry cause is combined of “emphasis OFF”, “monaural”,
“original”, “copyright exists”, and “write allowed”.
“original”, “copyright exists”, and “write allowed”.
Example When 07 is displayed:
Higher bit : 0 = 1000
n All 0
Lower bit : 7 = 0111
n b0+b1+b2
In this case, as b0, b1, and b2 are 1 and others are 0, it can be determined that the retry cause is combined of “emphasis ON”, “stereo”,
“original”, “copyright exists”, and “write prohibited”.
“original”, “copyright exists”, and “write prohibited”.
Hexadecimal n Binary Conversion Table
Hexadecimal
Binary
Hexadecimal
Binary
0
1
2
3
4
5
6
7
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
Reading the Track Mode Display
8
9
A
B
C
D
E
F
11
SECTION 2
GENERAL
LOCATION OF CONTROLS
• Front View
• Rear View
1
2
4
3
5
6
9
q;
qf
qj
qa
qg
qk
ql
wg
wk
wl
wh
wj
wd
wf
7
8
qh
qd
qs
w;
wa
ws
2
1
5
3
4
Photo: US model
1 TAPE deck
2 Liquid crystal display
3 TAPE Y button
4 TAPE Z button
5 TAPE x button
6 TAPE X button
7 TAPE REC z button
8 DSG button and indicator
9 VOLUME knob
0 MD 6 button
!¡ MD x button
!™ MD u button
!£ MD REC z button
!¢ CD 6 button
!∞ CD x button
!§ CD u button
!¶ CD > button
!• CD . button
!ª TUNER/BAND button
@º REPEAT DOLBY NR button and indicator
@¡ PLAY MODE DIRECTION button and indicator
@™ FUNCTION button and indicator
@£ ENTER/START button and indicator
@¢ SYNCHRO REC button and indicator
@∞ PHONES jack
@§ ?/1 button and indicator
@¶ Remote sensor
@• BASS knob
@ª TREBLE knob
2 Liquid crystal display
3 TAPE Y button
4 TAPE Z button
5 TAPE x button
6 TAPE X button
7 TAPE REC z button
8 DSG button and indicator
9 VOLUME knob
0 MD 6 button
!¡ MD x button
!™ MD u button
!£ MD REC z button
!¢ CD 6 button
!∞ CD x button
!§ CD u button
!¶ CD > button
!• CD . button
!ª TUNER/BAND button
@º REPEAT DOLBY NR button and indicator
@¡ PLAY MODE DIRECTION button and indicator
@™ FUNCTION button and indicator
@£ ENTER/START button and indicator
@¢ SYNCHRO REC button and indicator
@∞ PHONES jack
@§ ?/1 button and indicator
@¶ Remote sensor
@• BASS knob
@ª TREBLE knob
1 FM ANTENNA terminals
2 AM LOOP ANTENNA terminals
3 LINE OUT jacks
4 VIDEO IN jacks
5 SPEAKER terminals
2 AM LOOP ANTENNA terminals
3 LINE OUT jacks
4 VIDEO IN jacks
5 SPEAKER terminals
12
This section is extracted from
instruction manual.
instruction manual.
Step 2: Setting the time
You must set the time beforehand to use the timer
functions.
The clock is on a 24-hour system for the European
model, and a 12-hour system for other models.
The 24-hour system is used for illustration
purposes.
functions.
The clock is on a 24-hour system for the European
model, and a 12-hour system for other models.
The 24-hour system is used for illustration
purposes.
x
.
>
N
`/1
X
M
m
4,6
3,5
3,5
2
1
4
DISPLAY
CURSORT
1
Turn on the system.
2
Press CLOCK/TIMER SET.
The clock appears and the hour indication
flashes.
flashes.
3
Press . or > to set the hour.
4
Press ENTER/YES or CURSORt.
The minute indication flashes.
5
Press . or > to set the minute.
6
Press ENTER/YES.
The clock starts.
If you made a mistake
Press CURSORT or t repeatedly until the
incorrect item flashes, then set it again.
incorrect item flashes, then set it again.
To change the preset time
You can change the preset time while the system
is off.
is off.
1 Press DISPLAY to display the clock.
2 Press CLOCK/TIMER SET.
3 Repeat steps 3 to 6 of “Setting the time.”
2 Press CLOCK/TIMER SET.
3 Repeat steps 3 to 6 of “Setting the time.”
Tip
The upper dot of the colon flashes for the first
30 seconds, and the lower dot flashes for the last
30 seconds of each minute.
30 seconds, and the lower dot flashes for the last
30 seconds of each minute.
Click on the first or last page to see other CMT-CP33MD / HCD-CP33 / HCD-CP33K service manuals if exist.