Sony CMT-CP33MD / HCD-CP33 / HCD-CP33K Service Manual ▷ View online
17
3-9. CAM
3-10. SLIDER (CAM)
1
Two screws (BTP2.6x6)
2
Bracket (Guide L)
3
Leaf spring
5
Bracket (Guide R)
6
Slider (Cam)
4
Two screws (BTP2.6x6)
Set the shaft of Lever (O/C) to
be at the position in the figure.
be at the position in the figure.
Set the shaft of Cam gear to
be at the position in the figure.
be at the position in the figure.
1
Torsion spring
2
SW lever
3
Pulley
5
Gear
6
Gear
7
Roller
8
Cam
4
Spacer (55)
18
3-11. BASE UNIT (MBU-5A) AND BD (MD) BOARD
3-12. SW BOARD AND LOADING MOTOR (M103)
5
Two screws (BTP2.6x6)
6
SW board
4
Loading motor (M103)
3
Two screws
(PWH1.7x3)
1
Screw (PTPWH M2.6x6)
2
Gear B
1
Three screws
(BTP2.6x6)
2
Base unit (MBU-5A)
3
Remove the solder (Five portion)
4
Screw (M1.7x4)
6
Flexible board
(CN101)
7
BD (MD) board
5
Flexible board
(CN104)
19
SECTION 4
SERVICE MODE
Start
REC pause for 3 seconds
FWD REC
Fast forward
REV Play
REC pause for 3 seconds
REV REC
Rewind
FWD Play
Shut off
Shut off
Shut off
Shut off
1 minute
3 minutes
1 minute
3 minutes
Start
Open the disc tray
Close the disc tray
Play the last track
[Panel Test Mode]
Procedure:
1. Set to standby state.
2. Press three buttons of PLAY MODE DIRECTION , CD x ,
1. Set to standby state.
2. Press three buttons of PLAY MODE DIRECTION , CD x ,
and DSG simultaneously.
3. Liquid crystal display and LED are all turned on.
4. Pless MD Z to enter the version display mode. (destination,
4. Pless MD Z to enter the version display mode. (destination,
MC, CD, ST, TC, TA, TM)
5. Press MD u to enter the KEY, VOL, check mode. ( m
. and M > must be pressed for several seconds.)
6. To exit from this mode, press the buttons in the same way as
step 2.
[Tape Deck Aging Mode]
This mode can be used for operation check of tape deck section.
This mode can be used for operation check of tape deck section.
Procedure:
1. Set a tape in the tape deck.
2. Set to standby state.
3. Press three buttons of TAPE x , CD x , (CD), and TAPE
1. Set a tape in the tape deck.
2. Set to standby state.
3. Press three buttons of TAPE x , CD x , (CD), and TAPE
simultaneously.
4. The aging is executed in bellow sequence.
5. To exit from the aging mode, press the ?/1 button to turn the
5. To exit from the aging mode, press the ?/1 button to turn the
power OFF.
Aging mode sequence:
[CD Aging Mode]
This mode can be used for operation check of CD section.
This mode can be used for operation check of CD section.
Procedure:
1. Load a CD disc.
2. Set to standby state.
3. Press three buttons of TAPE x , CD x , and TUNER
1. Load a CD disc.
2. Set to standby state.
3. Press three buttons of TAPE x , CD x , and TUNER
simultaneously.
4. The aging is executed in bellow sequence.
5. To exit from the aging mode, press the ?/1 button to turn the
5. To exit from the aging mode, press the ?/1 button to turn the
power OFF.
Aging mode sequence:
[Cold Reset]
Clears all the memories and starts up the machine again.
Clears all the memories and starts up the machine again.
Procedure:
1. POWEWR ON state is in progress.
2. Press three buttons of CD x , PLAY MODE DIRECTION ,
1. POWEWR ON state is in progress.
2. Press three buttons of CD x , PLAY MODE DIRECTION ,
and MD Z simultaneously.
[Hot Reset]
Starts up the machine again holding the memory data.
Starts up the machine again holding the memory data.
Procedure:
1. POWEWR ON state is in progress.
2. Press three buttons of CD x , PLAY MODE DIRECTION ,
1. POWEWR ON state is in progress.
2. Press three buttons of CD x , PLAY MODE DIRECTION ,
and MD u simultaneously.
20
SECTION 5
TEST MODE (MD)
5-1. PRECAUTIONS FOR USE OF TEST MODE
• Use the RM-SJ373 supplied remote control (R).
• As loading related operations will be performed regardless of the test mode operations being performed, be sure to check that the disc
• As loading related operations will be performed regardless of the test mode operations being performed, be sure to check that the disc
is stopped before setting and removing it.
Even if the MD Z button is pressed while the disc is rotating during continuous playback, continuous recording, etc., the disc will not
stop rotating.
Therefore, it will be ejected while rotating.
Be sure to press the MD Z button after pressing the MENU/NO (R) button and the rotation of disc is stopped.
Even if the MD Z button is pressed while the disc is rotating during continuous playback, continuous recording, etc., the disc will not
stop rotating.
Therefore, it will be ejected while rotating.
Be sure to press the MD Z button after pressing the MENU/NO (R) button and the rotation of disc is stopped.
5-1-1. Recording laser emission mode and operating buttons
• Continuous recording mode (CREC MODE)
• Laser power check mode (LDPWR CHECK)
• Laser power adjustment mode (LDPWR ADJUST)
• Traverse (MO) check (EF MO CHECK)
• Traverse (MO) adjustment (EF MO ADJUST)
• When pressing the MD REC z button.
• Laser power check mode (LDPWR CHECK)
• Laser power adjustment mode (LDPWR ADJUST)
• Traverse (MO) check (EF MO CHECK)
• Traverse (MO) adjustment (EF MO ADJUST)
• When pressing the MD REC z button.
5-2. SETTING THE TEST MODE
The following are two methods of entering the test mode.
Procedure 1: With the power ON, press the CD x button while pressing the MD x and MD REC z buttons together.
Procedure 1: With the power ON, press the CD x button while pressing the MD x and MD REC z buttons together.
When the test mode is set, “Check” will be displayed. .(R) , > (R) switches between the following four groups;
···
···
Nn Check Nn Adjust Nn Service Nn Develop Nn ···.
Procedure 2: With the power ON, press the CD x button while pressing the MD x and SYNCHRO REC buttons together.
When the test mode is set, “TEMP CHECK” will be displayed. By setting the test mode using this procedure, only the “Check”
group of procedure 1 can be executed.
group of procedure 1 can be executed.
5-3. EXITING THE TEST MODE
Press the button, ?/1
5-4. BASIC OPERATIONS OF THE TEST MODE
All operations are performed using the .(R) , > (R) , ENTER/YES (R) button, and MENU/NO (R) button.
The functions of these buttons are as follows.
The functions of these buttons are as follows.
Function name
.(R) > (R)
ENTER/YES (R) button
MENU/NO (R) button
Function
Changes parameters and modes
Proceeds onto the next step. Finalizes input.
Returns to previous step. Stops operations.
[MC Cold Reset]
Clears the MD memory.
Clears the MD memory.
Procedure:
1. POWEWR ON. FUNCTION MD.
2. Press CD x , MD x and REPEAT simultaneously.
1. POWEWR ON. FUNCTION MD.
2. Press CD x , MD x and REPEAT simultaneously.
[MD SERVICE END]
Ends the service mode and clears the nonvolatile moemory.
Ends the service mode and clears the nonvolatile moemory.
Procedure:
1. The service mode is in progress.
2. Press CD x , MD x and ENTER/START simultaneously.
1. The service mode is in progress.
2. Press CD x , MD x and ENTER/START simultaneously.
[MD FLASH UP-DATE]
Writes data in the FLASH ROM from the disk.
Procedure:
1. POWER ON.
2. Press CD x , MD x and ?/1 simultaneously.
Writes data in the FLASH ROM from the disk.
Procedure:
1. POWER ON.
2. Press CD x , MD x and ?/1 simultaneously.
Click on the first or last page to see other CMT-CP33MD / HCD-CP33 / HCD-CP33K service manuals if exist.