Sony CMT-BT60 / CMT-BT60B / CMT-BT80W / CMT-BT80WB Service Manual ▷ View online
CMT-BT60/BT60B/BT80W/BT80WB
9
SECTION 2
DISASSEMBLY
•
This set can be disassembled in the order shown below.
2-1. DISASSEMBLY FLOW
SET
2-2. PANEL FRONT (GRILL) BLOCK
(Page
(Page
10)
2-3. ANT
BOARD
(CMT-BT80W/BT80WB)
(Page
(Page
11)
2-17. BLUETOOTH MODULE (BT1)
(Page
(Page
22)
2-19. SPEAKER (80 mm) (SP3, SP4)
(Page
(Page
24)
2-5. CD MECHANISM DECK BLOCK
(Page
(Page
12)
2-20. LOUDSPEAKER (65 mm)
(SP1,
(SP1,
SP2)
(Page
25)
2-18. PANEL TOP BLOCK
(Page
(Page
23)
2-4. FRONT ARM ASSY
(Page
(Page
11)
2-10. POWER UNIT BLOCK
(Page
(Page
17)
2-11. JACK BOARD BLOCK-1
(Page
(Page
18)
2-12. JACK BOARD BLOCK-2
(Page
(Page
19)
2-16. MAIN BOARD
(Page
(Page
22)
2-15. MAIN BOARD BLOCK
(Page
(Page
21)
2-6. HOLDER CDM BLOCK
(Page
(Page
13)
2-13. HEATSINK BCO BLOCK
(Page
(Page
20)
2-21. SPEAKER WIRE
(Page
(Page
26)
2-14. WiFi MODULE (WIFI1)
(CMT-BT80W/BT80WB)
(Page
(CMT-BT80W/BT80WB)
(Page
20)
2-7. FFC
GUIDE
(Page
14)
2-8. BOTTOM COVER (I)
(Page
(Page
15)
2-9. OPTICAL
PICK-UP
(CMS-S76RFS7G)
(OP1)
(Page
16)
2-22. PANEL REAR
(Page
(Page
27)
CMT-BT60/BT60B/BT80W/BT80WB
10
Note: Follow the disassembly procedure in the numerical order given.
2-2. PANEL FRONT (GRILL) BLOCK
Note 1: Please spread a sheet under
a unit not to injure grill side.
Note 2: Take care not to scratch.
4 six screws
(BTTP
M2.6)
5 Remove the panel front (grill) block
in the direction of an arrow.
qa panel front (grill) block
6 three claws
6 three claws
6 six claws
6 three claws
8 flexible flat cable (7P)
(CN3501)
0 flexible flat cable (8P)
– Rear bottom view –
– Front bottom view –
Note 4: When installing the flexible
flat cable, ensure the colored
line.
No slanting after insertion.
Note 5: When installing the panel
front (grill) block, align the
boss of panel front (grill)
with the ditch of the panel
rear.
Note 3: It is not necessary to remove
these two screws.
colored line
colored line
Insert is straight to the interior.
Insert is incline
flexible flat
cable
cable
flexible flat
cable
cable
connector
connector
panel front (grill)
panel rear
OK
NG
3 screw
(BVTP3
u 10)
3 screw
(BVTP3
u 10)
1 Insert a thin pin etc. below the
cap rear and remove to pull
and raise the cap rear.
cap rear
Distorted.
Wrong
location.
location.
2 cap rear
2 cap rear
OK
NG
NG
guide line
tape
(sub material)
(sub material)
FOe[ibOe IOat FabOe VettinJ
&aS rear VettinJ
9 tape
(sub
material)
7 cushion
(K)
CMT-BT60/BT60B/BT80W/BT80WB
11
2-4. FRONT ARM ASSY
2-3. ANT BOARD (CMT-BT80W/BT80WB)
3 tapping screw
(B2.6)
6 ANT board
:LUHVHWWLQJ
cushion (C)
ANT board
1 cushion (C)
2 lead wire
with
connector
lead wire with connector
5 tape (LCD)
4 Remove the ANT board
block in the direction
of an arrow.
–)URQWWRSYLHZ–
Note: Arrange downward and diagonally.
2 Put your finger into the notch portion of
the front arm assy and add the power
to the front side.
4 front arm assy
front arm assy
1 two screws
(PTP2
u 5)
3
Lift up the front arm assy
by pulling forward.
– Front top view –
CMT-BT60/BT60B/BT80W/BT80WB
12
2-5. CD MECHANISM DECK BLOCK
1 Solder the short-land.
Solder is removed cleanly.
Solder is not removed.
Note 2: When assembling the CD
mechanism deck block,
remove the solder of
short-land after connecting
all flexible flat cable
and
connector.
Note 1: Before disconnecting all flexible flat cable and connector of CD mechanism deck block, solder the short-land.
5 flexible flat cable (24P)
(CN501)
4 flexible flat cable (7P)
(CN831)
7 CD mechanism deck block
3 Remove the CD mechanism
deck block in the direction
of an arrow.
6 connector
(CN502)
OK
NG
– Front top view –
2 two screws
(BVTP3
u 10)
2 two screws
(BVTP3
u 10)
Note 3: When installing the flexible flat cable, ensure the colored line.
No slanting after insertion.
colored line
colored line
Insert is straight to the interior.
Insert is incline
flexible flat
cable
cable
flexible flat
cable
cable
connector
connector
OK
NG
Note 4: When you install the connector, please install them correctly.
There is a possibility that this machine damages when not
correctly installing it.
Insert is shallow
Insert is straight
to the interior.
to the interior.
connector
Insert is incline
connector
connector
connector
connector
connector
NG
OK
NG
Click on the first or last page to see other CMT-BT60 / CMT-BT60B / CMT-BT80W / CMT-BT80WB service manuals if exist.