Sony CMT-BT60 / CMT-BT60B / CMT-BT80W / CMT-BT80WB Service Manual ▷ View online
CMT-BT60/BT60B/BT80W/BT80WB
25
2-20. LOUDSPEAKER (65 mm) (SP1, SP2)
– Front bottom view –
3 Remove the solder.
[red]
3 Remove the solder.
[red]
3 Remove the solder.
[white]
3 Remove the solder.
[white]
:ire VettinJ
wire
OK
NG
terminal
wire
terminal
[red] (+)
Hole is visible.
Hole is hidden.
OK
NG
1 four screws
(BVTP3
u 10)
1 four screws
(BVTP3
u 10)
2 Remove the loudspeaker
(65 mm) block in the
direction of an arrow.
2 Remove the loudspeaker
(65 mm) block in the
direction of an arrow.
4 loudspeaker (65 mm)
(L-CH)
(SP1)
4 loudspeaker (65 mm)
(R-CH)
(SP2)
:ire VettinJ
wire
OK
NG
terminal
wire
terminal
[white] (-)
Hole is visible.
Hole is hidden.
OK
NG
CMT-BT60/BT60B/BT80W/BT80WB
26
2-21. SPEAKER WIRE
1 cushion (K)
2 speaker wire (L-CH)
2 speaker wire (R-CH)
1 cushion (K)
– Front top view –
:ire VettinJ
cushion (K)
speaker wire (L-CH)
speaker wire (R-CH)
cushion (K)
bottom side
top side
OK
NG
Hole is visible.
Hole is hidden.
– Panel rear inner view –
CMT-BT60/BT60B/BT80W/BT80WB
27
2-22. PANEL REAR
1 cushion (PS)
1 cushion (PS)
2 cushion (L)
2 cushion (L)
7 cushion (PET)
7 cushion (PET)
6 box SP (R) block
6 box SP (L) block
box SP (R)
box SP (L)
FXVKLRQVHDO63VHWWLQJ
FXVKLRQVHDO63VHWWLQJ
cushion (seal SP)
cushion (seal sp)
3 two screws
(BVTP3
u 10)
3 three screws
(BVTP3
u 10)
3 screw
(BVTP3
u 10)
3 screw
(BVTP3
u 10)
3 screw
(BVTP3
u 10)
4 Remove the box SP (L) block
in the direction of an arrow.
4 Remove the box SP (R) block
in the direction of an arrow.
–)URQWWRSYLHZ–
–5HDUYLHZ–
–5HDUYLHZ–
5 cushion (seal SP)
Note 1: When replacing the panel rear,
make sure to replace the cushion
(seal SP) together.
8 panel rear
Note
1: When replacing the panel rear, make sure
to replace the cushion (seal SP) together.
5 cushion (seal SP)
Note
1: When replacing the panel rear,
make sure to replace the cushion
(seal SP) together.
Note 2: Get started paste from
this
this
part.
Note 2: Get started paste from
this
this
part.
CMT-BT60/BT60B/BT80W/BT80WB
28
SECTION 3
TEST MODE
COLD RESET
It can clears all data including preset data stored in the memory to
initial conditions. Execute this mode when returning the this unit
to the customer.
It can clears all data including preset data stored in the memory to
initial conditions. Execute this mode when returning the this unit
to the customer.
Procedure:
1. Press the [
1. Press the [
?
/
1
] button to turn the power on.
2. Press two buttons of the [
x
] and [
?
/
1
] simultaneously.
3. The message “RESET” (CMT-BT60/BT60B) or “ALLRESET”
(CMT-BT80W/BT80WB) is displayed on the liquid crystal
display, then becomes the standby state.
display, then becomes the standby state.
AUTO STANDBY TEST
It can confi rm the auto standby function operates normally.
The auto standby function operates in 60 seconds in this mode.
(Usually, it takes 30 minutes)
It can confi rm the auto standby function operates normally.
The auto standby function operates in 60 seconds in this mode.
(Usually, it takes 30 minutes)
Procedure:
1. Press the [
1. Press the [
?
/
1
] button to turn the power on.
2. Press the [FUNCTION] button to turn except “FM”, “AM”
and “DAB”.
3. Press two buttons of the [BASS BOOST] and [FUNCTION]
simultaneously for three seconds.
4. It enters the auto standby test mode, and the following screen
is displayed on the liquid crystal display.
(In this mode, “ST” continues blinking on the liquid crystal
display)
display)
Signal level
(0 or 1)
Countdown
timer
(60 to 0)
ST
Screen display
5. In the case of the following states, the countdown timer de-
creases. This unit will become standby states if the countdown
timer decreases to “0”.
timer decreases to “0”.
• Operation is not performed.
• The signal level is lower than threshold.
Releasing method:
Press two buttons of the [BASS BOOST] and [FUNCTION] si-
multaneously for three seconds.
Press two buttons of the [BASS BOOST] and [FUNCTION] si-
multaneously for three seconds.
COMMON TEST
It can confi rm the MAX/MIN of volume.
It can confi rm the MAX/MIN of volume.
Procedure:
1. Press the [
1. Press the [
?
/
1
] button to turn the power on.
2. Press two buttons of the [BASS BOOST] and [
u
] simultane-
ously for three seconds.
3. It enters the common test mode.
(In this mode, “cPLAY” and “SLEEP” continues blinking on
the liquid crystal display)
the liquid crystal display)
4. When pressing the [VOL +]/[VOL
−] button, the message is
changed with VOL MIN
↔ VOL 17 ↔ VOL MAX on the
liquid crystal display.
Releasing method:
Press the [
Press the [
?
/
1
] button to turn the power off.
PANEL TEST
It can confi rm the liquid crystal display, LEDs, model name, desti-
nation, software version and buttons.
It can confi rm the liquid crystal display, LEDs, model name, desti-
nation, software version and buttons.
Procedure:
1. Press the [
1. Press the [
?
/
1
] button to turn the power on.
2. Press two buttons of the [FUNCTION] and [VOL –] simulta-
neously for three seconds.
3. It enters the panel test mode, and all segments on the liquid
crystal display and all LEDs light up.
Screen display
c
PLAY
c
REC UPDATE
FLDR SHUFPGM
1
SLEEP ST NX
REC
4. When pressing the [
>
TUNE +] button, the model name and
destination are displayed on the liquid crystal display alter-
nately.
nately.
(In this mode, “ST” continues blinking on the liquid crystal
display)
display)
Screen display
Screen display
ST
ST
Model Name
Display
CMT-BT60
HFX-185
CMT-BT60B
HFX-186
CMT-BT80W
HFX-182
CMT-BT80WB
HFX-183
Destination
Display
Destination
Display
US and Canadian
NA
Mexican
MX
AEP and UK
CE2
Brazilian
BR
110 – 240V AC area
in E
in E
LATIN
Singapore, Thai,
Korean
Korean
ASIA2
Australian
AU
Taiwan
TW
Chinese
CN
Indian
E12
Russian
RU
5. When pressing the [
>
TUNE +] button again, the MC ver-
sion is displayed on the liquid crystal display.
6. Each
time
[
>
TUNE +] button is pressed, the display chang-
es MCS version, MTK version, NWM version (CMT-BT80W/
BT80WB only), BTM version, GC version, USBL version,
NWA version (CMT-BT80W/BT80WB only), NWD version
(CMT-BT80W/BT80WB only), BTA version, BTL version,
CD version, CDMA version, CDMB version, ST version, TA
version and TM version this order, and returns to the MC ver-
sion display.
BT80WB only), BTM version, GC version, USBL version,
NWA version (CMT-BT80W/BT80WB only), NWD version
(CMT-BT80W/BT80WB only), BTA version, BTL version,
CD version, CDMA version, CDMB version, ST version, TA
version and TM version this order, and returns to the MC ver-
sion display.
7. When pressing the [
x
] button while the each version is dis-
played, year, month and day of the software creation is dis-
played. When pressing the [
played. When pressing the [
x
] button again, the display re-
turns to the each version display.
8. When pressing the [
.
TUNE
−] button, “K 0” is displayed
on the liquid crystal display.
9. Each time a button is pressed, “K 0” value increases. However,
once a button is pressed, it is no longer taken into account.
When pressing the all buttons, display becomes “K12”.
Releasing method:
Press two buttons of the [FUNCTION] and [VOL –] simultane-
ously for three seconds.
Press two buttons of the [FUNCTION] and [VOL –] simultane-
ously for three seconds.
Ver. 1.3
Click on the first or last page to see other CMT-BT60 / CMT-BT60B / CMT-BT80W / CMT-BT80WB service manuals if exist.