DOWNLOAD Sony CFD-V27 Service Manual ↓ Size: 6.1 MB | Pages: 57 in PDF or view online for FREE

— 9 —

Follow the installation procedure in the numerical order given.

1 Align the pointer with the groove of front cabinet and insert it as shown in the illustration.
2 Align Tuning knob with front cabinet and fasten the screw.

3 Turn the Tuning knob in the direction of the arrow as shown in the illustration until pointer agrees with scale “ 0 ” (at leftmost end of

scale).

4 Turn the tuning capacitor gear fully in the direction of the arrow as shown in the illustration.
5 Fasten the front cabinet and rear cabinet with the screws.

1

 Pointer

Tuning knob B

Front Cabinet

2

 Screw (2.6 

×

 8)

3

 Tuning knob

4

 Tuning capacitor gear

5

Rear cabinet

— 10 —

Torque Meter

CQ-403A

Meter Reading

more than 60 g

(more than 2.12 oz)

Procedure :
Mode : Playback

Adjustment Value : normal tape speed
Adjust the tape speed adjustment control inside motor, so that the
frequency counter reading becomes 3,000 Hz.

Frequency difference between the beginning and the end of the
tape should be within 1.5% (45 Hz).

HP OUT

32 

Ω

0.25 V (–10 dB)

Output

Load impedance

Output signal level

Test Tape

WS-48A

P-4-A063

Used for

Tape speed adjustment

Head azimuth  adjustment.

Signal

3 kHz, 0 dB

6.3 kHz, –10 dB

1.

Clean the following parts with a denatured-alchool-moistened
swab:

record/playback head

pinch roller

erase head

rubber belts

capstans

2.

Demagnetize the record/playback head with a head
demagnetizer. (Do not bring the head demagnetizer close to
the erase head.)

3.

Do not use a magnetized screwdriver for the adjustments.

4.

After the adjustments, apply suitable locking compound to the
parts adjusted.

Meter Reading

18 – 60 g

•

cm

(0.25 – 0.83 oz

•

inch)

1.0 – 5.0 g

•

cm

(0.014 – 0.069 oz

•

inch)

45 – 95 g

•

cm

(0.62 – 1.32 oz

•

inch)

45 – 95 g

•

cm

(0.62 – 1.32 oz

•

inch)

Mode

FWD

FWD

back tension

Fast Forward

Rewind

Torque Meter

CQ-102C

CQ-201B

0dB = 0.775V

Tape speed adjustment 
control inside motor

32 

Ω

test tape
WS-48A
(3kHz, 0dB)

set

digital frequency
counter

J301 (phones)

+

–

Digital frequency counter

2,910 – 3,090Hz

— 11 —

•

 Switch Location

VOLUME

: MAX

MEGA BASS

: OFF

PRESET SOUND MODE : OFF

BAND : AM
Signal generator

BAND : FM
Signal generator

0 dB = 1 µV

• Repeat the procedures in each adjustment several times for the

maximum level meter indication.

• The frequency coverage and tracking adjustments should be

finally done by the trimmer capacitors.

AM IF ADJUSTMENT

Adjust for a maximum reading on level meter.

T2

455 kHz

AM TRACKING ADJUSTMENT

Adjust for a maximum reading on level meter.

L3

620 kHz

CT3

1,400 kHz

FM TRACKING ADJUSTMENT

Adjust for a maximum reading on level meter.

L1

86.5 MHz

CT1

109.5 MHz

AM FREQUENCY COVERAGE ADJUSTMENT

Adjust for a maximum reading on level meter.

L4

520 kHz

CT4

1,780 kHz

FM IF ADJUSTMENT

Adjust for a maximum reading on level meter.

T1

10.7 MHz

FM FREQUENCY COVERAGE ADJUSTMENT

Adjust for a maximum reading on level meter.

L2

86.5 MHz

CT2

109.5 MHz

Adjustment Location : Main board (See page 13)

Put the lead-wire
antenna close to
the set.

30% amplitude modulation by 400Hz
signal.
Output level : as low as possible

AM RF signal
generator

0.01

µ

F

FM RF signal
generator

FM ANT IN
terminal

75kHz (100%) amplitude modulation
by 1kHz signal.
Output level : as low as possible

32

Ω

set

+

–

level meter

J301 (phones)

— 12 —

1. Connect frequency counter to the positions shown below.
2. Tune the set to 98MHz.
3. Adjust RV1 so that the frequency counter reading becomes

76,000 Hz.

Adjustment Location : MAIN board (See page 13)

BLACK

10.64MHz

BLUE

10.67MHz

RED

10.70MHz

ORANGE

10.73MHz

WHITE

10.76MHz

0.01

µ

F

FM RF Signal generator

FM ANT IN terminal

Carrier frequency : 98MHz
IF frequency : According to
the color of CF1.
Modulation : no modulation
Output level : 0.1V (100dB)

color
mark

CF1

Frequency counter

75,800 – 76,200 Hz

Frequency counter

0.01

µ

F

+
–

33k 

Ω

IC1 Pin 

4

IC1 Pin 

7