DOWNLOAD Sony CFD-RG880CP Service Manual ↓ Size: 5.02 MB | Pages: 75 in PDF or view online for FREE

× 6)

 Remove soldering from the four points.

[MC  COLD  RESET]
The cold reset clears all data including preset data stored in the 
memory to initial conditions. Execute this mode when returning 
the set to the customer.
Procedure:
1.  In the standby status, press the [POWER] button to turn the 

power on.

2.  Press three buttons of [

x

], [MODE] and at last [POWER] si-

multaneously.

3.  When “RESET” appears, the machine enters standby status.

[PANEL  TEST  MODE]
Enter The Panel Test Mode
Procedure:
1.  In the standby status, press the [POWER] button to turn the 

power on.

2.  Press three buttons of [REPEAT], [

x

], and [DSPL/ENT] si-

multaneously.

3.  When the panel test mode is activated, LEDs and segments of 

LCD are all turned on.

Version Check
Procedure:
1.  In the panel test mode (all LEDs and segments of LCD are 

turned on), press the [ROCK] button.

2.  On the LCD, date and version are displayed “xxxxxxxx”. For 

example, “0305V001”.

3.  From this status, press the [DANCE] button, and the destina-

tion is displayed. For example, “1024 MX2”.

4.  To release from this mode, press three buttons of [REPEAT], 

[

x

], and [DSPL/ENT] simultaneously.

[CHANGE-OVER  THE  AM  TUNING  INTERVAL]
The AM tuning interval can be changed over 9 kHz or 10 kHz.
Procedure:
1.  Press the [POWER] button to turn the power on.
2.  Press the [RADIO/BAND] button to select TUNER (AM) 

function.

3.   Select the AM BAND mode and press the [DSPL/ENT] button 

for an extended time in the AM BAND state.

4.   Then, press the [AUTO PRESET/RADIO/BAND] for an ex-

tended time.

5.  Next, press the [PRESET +] [PRESET –] button select either 

9k/10k.

6.  Finally, press the [DSPL/ENT] button to set the selected step.

[CD  SERVICE  MODE]
This mode can move the SLED of the optical pick-up, and also can 
turn the optical pick-up laser power on and off.
Procedure:
1.  Press the [POWER] button to turn the power on.
2.  Press the [CD] button to select the CD mode.
3.  Press three buttons of [

x

], [VOL +], and [SALSA] simultane-

ously.

4.  It enters the CD service mode and displays “SE MODE”.
5.  To exit from this mode, press three buttons of [

x

], [VOL +], 

and [SALSA] simultaneously.

Key Operation:
[PRESET+ 

>

], [PRESET– 

.

]: 

 

Use these keys to move the SLED.

 When 

[PRESET+ 

>

] is pressed in this mode, the 

SLED moves to outer circumference and the message 
“SL OUT” is displayed. 

 When 

[PRESET– 

.

] is pressed in this mode, the 

SLED moves to inner circumference and the message 
“SL IN” is displayed. 

[MODE] :  Use this key to turn the optical pick-up laser power on 

and off. When the laser power is turned on, the mes-
sage “LD ON” is displayed. When the laser power is 
turned off, the message “LD OFF” is displayed. 

Precaution
1.  Clean the following parts with a denatured alcohol-moistened 

swab: 

     

record/playback heads  pinch rollers

     

erase head 

rubber belts

     capstan 

idlers

2.  Demagnetize the record/playback head with a head demag-

netizer. (Do not bring the head magnetizer close to the erase 
head.)

3.  Do not use a magnetized screwdriver for the adjustments.
4.  After the adjustments, appiy suitable locking compound to the 

parts adjusted.

5.  The adjustments should be performed with the rated power 

supply voltage unless otherwise noted.

FWD

CQ-102AS

2.95 – 6.86 mN • m

(30 – 70 g • cm)

(0.42 – 0.97 oz • inch)

FWD
back tension

CQ-102C

0.15 – 0.53 mN • m

(1.5 – 5.5 g • cm)

(0.021 – 0.076 oz • inch)

FF

CQ-201AS

more than 5.88 mN • m

(more than 60 g • cm)

(more than 0.83 oz • inch)

REW

CQ-201B

more than 5.88 mN • m

(more than 60 g • cm)

(more than 0.83 oz • inch)

FWD

CQ-403A

more than 100 g

(more than 3.53 oz)