Sony CFD-E55L Service Manual ▷ View online
– 5 –
Basic Operations
8
GB
Playing a tape
Connect the supplied AC power cord (see page 26).
1
Press xZ to open the tape
compartment and insert a
recorded tape. Use TYPE I
(normal) tape only. Close the
compartment.
compartment and insert a
recorded tape. Use TYPE I
(normal) tape only. Close the
compartment.
2
Press N.
The player turns on (direct
power-on) and starts playing.
power-on) and starts playing.
With the side you want
to play facing you
to play facing you
Display
1
2
STOP/EJECT
PLAY
Basic Operations
Basic Operations
9
GB
Use these buttons for additional operations
To
Press
adjust the volume
VOL +, –
stop playback
xZ
fast-forward or rewind the tape M or m
pause playback
X
Press the button again to
resume play after pause.
resume play after pause.
eject the cassette
xZ
turn on/off the player
OPERATE
Tip
Next time you want to
listen to a tape, just
press N. The player
turns on automatically
and starts playing the
tape.
listen to a tape, just
press N. The player
turns on automatically
and starts playing the
tape.
xZ
X
m
, M
OPERATE
VOL –, +
Basic Operations
10
GB
Recording on a tape
Connect the supplied AC power cord (see page 26).
1
Press xZ to open the tape
compartment and insert a blank
tape. Use TYPE I (normal) tape
only.
compartment and insert a blank
tape. Use TYPE I (normal) tape
only.
2
Select the program source you
want to record.
want to record.
To record from the CD player,
insert a CD (see page 4) and press
x
insert a CD (see page 4) and press
x
on the CD section.
To record from the radio, tune in
the station you want (see page 6).
the station you want (see page 6).
3
1
With the side you want to
record on facing you
record on facing you
Display
STOP/EJECT
OPERA
TE
OPR/BA
TT
BA
N
D
RA
D
IO
VO
L
Basic Operations
Basic Operations
11
GB
3
Press z to start recording
(N is depressed automatically).
(N is depressed automatically).
Use these buttons for additional operations
Tips
• Adjusting the volume or
• Adjusting the volume or
the audio emphasis (see
page 28) will not affect
the recording level.
page 28) will not affect
the recording level.
• If the MW/LW program
makes a whistling
sound after you've
pressed z in step 3,
press PLAY MODE•
MONO/ST ISS
(Interference Suppress
switch) repeatedly until
the noise is at a
minimum.
sound after you've
pressed z in step 3,
press PLAY MODE•
MONO/ST ISS
(Interference Suppress
switch) repeatedly until
the noise is at a
minimum.
• For the best results, use
the AC power as a
power source.
power source.
• To erase a recording,
proceed as follows:
1 Insert the tape whose
1 Insert the tape whose
recording you want to
erase.
erase.
2 Press X.
3 Press N.
4 Press z.
5 Press X.
3 Press N.
4 Press z.
5 Press X.
To
Press
stop recording
xZ
pause recording
X
Press the button again to
resume recording.
resume recording.
turn on/off the player
OPERATE
xZ
X
OPERATE
PLAY MODE
MONO/ST ISS
MONO/ST ISS
N
REC
– 6 –
The Timer
20
GB
Before you set the clock, connect the power source (see
page 26).
page 26).
1
Press CLOCK for 2 seconds until the hour digit
flashes.
flashes.
2
Press TUNE TIME SET + or – until you set the
current hour. Then press DSPL ENT MEM.
current hour. Then press DSPL ENT MEM.
The minute digits flash. Set the minutes by
pressing TUNE TIME SET + or – until the correct
minute is displayed.
pressing TUNE TIME SET + or – until the correct
minute is displayed.
3
Press DSPL ENT MEM.
The clock starts from 00 seconds.
Setting the clock
“– –:– –” indication appears in the
display until you set the clock.
display until you set the clock.
The Timer
Tip
The time display
system:
24-hour system
system:
24-hour system
,
CLOCK
DSPL
ENT MEM
ENT MEM
TUNE
TIME SET –, +
TIME SET –, +
– 7 –
SECTION 3
DISASSEMBLY
• This set can be disassembled in the order shown below.
Note:
Follow the disassembly procedure in the numerical order given.
LOWER CABINET SECTION
Set
Lower cabinet
section
section
MAIN board
Tape mechanism
deck section
deck section
Cassette lid assy
and cassette holder
and cassette holder
Head (HRP301), Motor assy (M301)
and belt
and belt
CD board
Optical pick-up
section
section
Front cabinet
section
section
CD lid
section
section
2
three screws
(BTP3
(BTP3
×
12)
3
lower cabinet section
4
connector
(CNP310)
(CNP310)
2
five screws
(BTP3
(BTP3
×
12)
1
battery case lid
4
two connectors
(CNP704, CNP308)
(CNP704, CNP308)
4
connector
(CNP307)
(CNP307)
– 8 –
FRONT CABINET SECTION
MAIN BOARD
2
two screws
(BTP3
(BTP3
×
12)
A
1
three connectors
(CNP302, 303, 309)
(CNP302, 303, 309)
2
two screws
(BTP3
(BTP3
×
12)
3
Remove the front
cabinet section in
the arrow
cabinet section in
the arrow
A
direction.
rear cabinet
section
section
2
two screws
(BVTP3
(BVTP3
×
10)
1
two connectors
(CNP304, 305)
(CNP304, 305)
1
three connectors
(CNP306, 311, 312)
(CNP306, 311, 312)
2
two screws
(BVTP3
(BVTP3
×
10)
3
MAIN board
1
connector
(CNP1)
(CNP1)
Click on the first or last page to see other CFD-E55L service manuals if exist.