Sony CFD-6 Service Manual ▷ View online
– 5 –
SECTION 3
DISASSEMBLY
Note
: Follow the disassembly procedure in the numerical order given.
3-1. CABINET (FRONT) REMOVAL
3-2. TUNER DIAL, TUNER BOARD REMOVAL
2
Two screws (3x14)
5
STOP/EJECT button
4
Two screws (3x14)
3
Telescopic anttena
1
Two screws (3x14)
7
Cabinet (Front)
6
6
Screw (B 2.6x6)
7
Tuner dial
Cabinet (Rear)
5
Tuner board
3
Two screws (BVTP 3x10)
4
Two screws (BVTP 3x10)
2
Tuner plate
1
Screw (BVTP 3x10)
– 6 –
3-3. MECHANISM DECK, MAIN BOARD REMOVAL
6
Three screws (BVTP 3x10)
1
Four screws (BVTP 3x10)
2
Mechanism deck
5
Two screws (BVTP 3x10)
7
Main board
Cabinet (Rear)
4
Knob (Tone)
3
Knob (Volume)
3-4. CD CABINET, CABINET (REAR) REMOVAL
2
CD Cabinet
1
Cabinet (Rear)
– 7 –
3-5. MAGNET, CHUCKING PLATE REMOVAL
1
Screw (BVTP 3x8)
2
Chucking plate
Magnet
Holder (Chuck)
Chucking plate
1
3
2
3
Screw (+B 2.6x6)
2
Tuning dial (Knob)
Tuning shaft
Tuner board
1
(Fig. 1)
SECTION 4
DIAL POINTER INSTALLATION
Note :
Follow the installation procedure in the numerical order given.
1. Turn tuning shaft fully to arrow direction.
2. Fit tuning shaft to hole of tuning dial (knob) and then install it. (Fig. 1)
3. Fasten the tuning dial (knob) to the tuner board with the screw.
2. Fit tuning shaft to hole of tuning dial (knob) and then install it. (Fig. 1)
3. Fasten the tuning dial (knob) to the tuner board with the screw.
– 8 –
SECTION 5
ADJUSTMENTS
5-1. MECHANICAL ADJUSTMENTS
PRECAUTION
1. Clean the following parts with a denatured-alcohol-moistened
swab :
record/playback head
pinch roller
erase head
rubber belts
capstan
2. Demagnetize the record/playback head with a head demagnetizer.
(Do not bring the head demagnetizer close to the erase head.)
3. Do not use a magnetized screwdriver for the adjustments.
4. After the adjustments, apply suitable locking compound to the
4. After the adjustments, apply suitable locking compound to the
parts adjusted.
Torque Measurement
Torque
Torque Meter
Meter Reading
Forward
CQ-102C
30 – 70 g • cm
(0.42 - 0.97 oz• inch)
Forward
CQ-102C
1.5 – 5.5 g • cm
back tension
(0.020- 0.076 oz• inch)
Fast Forward
CQ-201B
more than 60g • cm
(more than 0.84 oz• inch)
Rewind
CQ-201B
more than 60g • cm
(more than 0.84 oz• inch)
Tape Tension Measurement
Tension Meter
Meter Reading
CQ-403A
more than 100g
(more than 3.53 oz)
5-2. ELECTRICAL ADJUSTMENTS
TAPE RECORDER SECTION
Standard Output Level
Output terminal
HP OUT
load impedance
33
Ω
output signal level
0.25V ( – 10 dB)
Test Tape
Type
Signal
Used for
WS-48A
3kHz, 0dB
Tape Speed Adjustment
P-4-A063
6.3kHz, –10dB
Head Azimuth Adjustment
0dB=0.775V
Tape Speed Adjustment
Procedure :
Mode : Playback
set
test tape
WS-48A
(3kHz, 0dB)
WS-48A
(3kHz, 0dB)
33
Ω
speed checker
LFM-30 or
digital frequency
counter
LFM-30 or
digital frequency
counter
J302 (phones)
– +
Adjustment Value :
Speed checker
Digital frequency counter
–1 to
±
1%
2,970 – 3,030Hz
Frequency difference between the beginning and the end of the tape
should be within 1.5% (45Hz).
should be within 1.5% (45Hz).
Adjustment Location :
tape speed adjustment
control inside moter
control inside moter
Click on the first or last page to see other CFD-6 service manuals if exist.