CFD-101 — Sony Audio Service Manual (repair manual)

Model
CFD-101
Pages
38
Size
438.94 KB
Type
PDF
Document
Service Manual
Brand
Device
Audio
File
cfd-101.pdf
Date

View Sony CFD-101 Service Manual online

– 1 –
Model Name Using Similar Mechanism
CFD-121
CD Mechanism Type
KSM-213BAN
Optical Pick-up Name
KSS-213B/K
Model Name Using Similar Mechanism
CFD-121
Tape Transport Mechanism Type
MF-121
SERVICE MANUAL
US Model
Canadian Model
AEP Model
E Model
Australian Model
Tourist Model
PX Model
– Continued on next page –
AUDIO POWER SPECIFICATIONS (US Model)
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION
With 3.2-ohm loads, both channels driven from 150 -10,000 Hz; rated 2 W
per channelminimum RMS power, with no more than 10 % total harmonic
distortion in AC operation.
Other Specifications
CD player section
System
Compact disc digital audio system
Laser diode properties
Material: GaAlAs
Wave length: 780 nm
Emission duration: Continuous
Laser output: Less than 44.6 µW
(This output is the value measured at a distance of about 200 mm from the objective lens surface
on the optical pick-up block with 7 mm aperture.)
Spindle speed
200 r/min (rpm) to 500 r/min (rpm) (CLV)
Number of channels
2
Frequency response
20 - 20,000 Hz +1/–2dB
Wow and flutter
Below measurable limit
SPECIFICATIONS
CFD-101
CD
Section
TC
Section
Radio section
Frequency range
FM:
Except AEP, G, IT, EA model
87.6 - 108 MHz
AEP, G, EA model
87.6 - 107 MHz
IT model
87.5 - 108 MHz
AM:
US, CND, C&SA model
530 - 1,710 kHz
AEP, G model
531 - 1,602 kHz
E, EA, HK, PX, AUS, JE, TW model
530 - 1,605 kHz
IT model
526.5 - 1,606.5 kHz
IF
FM: 10.7 MHz
AM: 455 kHz
Aerials
FM: Telescopic aerial
AM: Built-in ferrite bar aerial
Cassette-corder section
Recording system
4-track 2 channel stereo
Fast winding time
Approx. 115 s (sec.) with Sony cassette C-60
Frequency response
TYPE I (normal): 70 - 10,000 Hz
MICROFILM
CD RADIO CASSETTE-CORDER
– 2 –
This appliance is classified as
a CLASS 1 LASER
product.
The CLASS 1 LASER
PRODUCT MARKING is
located on the rear exterior.
CAUTION
Use of controls or adjustments or performance of proce-
dures other than those specified herein may result in haz-
ardous radiation exposure.
Flexible Circuit Board Repairing
Keep the temperature of the soldering iron around 270˚C during
repairing.
Do not touch the soldering iron on the same conductor of the circuit
board (within 3 times).
Be careful not to apply force on the conductor when soldering or
unsoldering.
Notes on Chip Component Replacement
Never reuse a disconnected chip component.
Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR
BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-up
block. Therefore, when checking the laser diode emission, observe
from more than 30 cm away from the objective lens.
CHUCK PLATE JIG ON REPAIRING
On repairing CD section, playing a disc without the CD lid, use Chuck
Plate jig.
• Code number of Chuck Plate jig : X-4918-255-1
General
Speaker
Full range: 10 cm dia., 3.2 ohms, cone type (2)
Outputs
Headphones jack (stereo minijack)
For 16 - 68 ohms impedance headphones
Power output (excluding US model)
2.3 W + 2.3 W (at 3.2 ohms, 10 % harmonic distortion)
Power requirements
120 V AC, 60 Hz (US, CND, TW, C&SA model)
220 - 230 V AC, 50 Hz (AEP, G, IT model)
230 - 240 V AC, 50 Hz (AUS model)
110 - 120 V, 220 - 240 V AC selectable 50/60 Hz (E, EA, HK, PX, JE model)
9 V DC, 6 R20 (size D) batteries
Power consumption
AC 25 W (TW model)
AC 20 W (Except TW model)
Battery life
For CD radio cassette-corder:
FM recording
Sony R20P: approx. 13.5 h
Sony alkaline LR20: approx. 19 h
Tape playback
Sony R20P: approx. 7.5 h
Sony alkaline LR20: approx. 12 h
CD playback
Sony R20P: approx. 2.5 h
Sony alkaline LR20: approx. 4.5 h
Dimensions
Approx. 446
×
165
×
234 mm (w/h/d)
(17 
5/8
 
×
1/2
 
×
1/4
 inches) (incl. projecting parts)
Mass
Approx. 3.8 kg (8 lb. 6 oz) (incl. batteries)
Supplied accessory
AC power cord (1)
Design and specifications are subject to change without notice.
• Abbreviation
G
: German model
IT
: Italian model
EA
: Saudi Arabia model
CND
: Canadian model
C&SA : Central and South American model
HK
: Hong Kong model
AUS
: Australian model
JE
: Tourist model
TW
: Taiwan model
HOW TO CHANGE THE CERAMIC FILTERS
This model is used two ceramic filters of CF1 and 3.
You must use same type of color marked ceramic filters in order to
meet same specifications.
Therefore, the ceramic filter must change two pieces together since
it's supply two pieces in one package as a spare parts.
red
10.70 MHz
blue
10.67 MHz
orange
10.73 MHz
black
10.64 MHz
white
10.76 MHz
mark
CF1
CF3
Center
Frequency
mark
mark
– 3 –
SAFETY-RELATED  COMPONENT  WARNING!!
COMPONENTS  IDENTIFIED  BY  MARK  
!
  OR  DOTTED  LINE
WITH  MARK  
!
  ON  THE  SCHEMATIC  DIAGRAMS  AND  IN  THE
PARTS  LIST  ARE  CRITICAL  TO  SAFE  OPERATION.  REPLACE
THESE  COMPONENTS  WITH  SONY  PARTS  WHOSE  PART
NUMBERS  APPEAR  AS  SHOWN  IN  THIS  MANUAL  OR  IN
SUPPLEMENTS  PUBLISHED  BY  SONY.
To Exposed Metal
Parts on Set
0.15µF
1.5k
AC
voltmeter
(0.75V)
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
SAFETY  CHECK-OUT
After correcting the original service problem, perform the following
safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs, screws,
and all other exposed metal parts for AC leakage. Check leakage as
described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a re-
turn to chassis, must not exceed 0.5 mA (500 microampers).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245 digi-
tal multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a VOM
or battery-operated AC voltmeter. The “limit” indication is 0.75
V, so analog meters must have an accurate low-voltage scale. The
Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM
that is suitable. Nearly all battery operated digital multimeters that
have a 2V AC range are suitable. (See Fig. A)
LASER DIODE AND FOCUS SEARCH OPERATION CHECK
1. Open the lid for CD.
2. Push on PUSH SWITCH (S704) as following figure.
3. Confirm the laser diode emission while observing the objecting
lens. When there is no emission, Auto Power Control circuit or
Optical Pick-up is broken.
Objective lens moves up and down once for the focus search.
ATTENTION AU COMPOSANT AYANT RAPPORT
 À LA SÉCURITÉ!!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 
!
 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE  DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
S704
– 4 –
TABLE OF CONTENTS
1. GENERAL
Playing a CD ............................................................................. 5
Listening to the radio ................................................................. 6
Playing a tape ............................................................................ 7
Recording on a tape ................................................................... 8
2. DISASSEMBLY
2-1. Front Cabinet ........................................................................... 9
2-2. MD Block ................................................................................ 9
2-3. AUDIO Board ........................................................................ 10
2-4. Tuner Block ........................................................................... 10
2-5. CD Block ............................................................................... 11
2-6. Power Board .......................................................................... 11
2-7. Knob (TU) Setting ................................................................. 12
3. MECHANICAL ADJUSTMENTS
..............................
13
4. ELECTRICAL ADJUSTMENTS
4-1. Tape Recorder Section .......................................................... 13
4-2. Tuner Section ........................................................................ 15
4-3. CD Section ............................................................................ 17
5. DIAGRAMS
5-1. Circuit Boards Location ........................................................ 21
5-2. Printed Wiring Boards ........................................................... 22
5-3. Schematic Diagram ............................................................... 25
5-4. IC Pin Description ................................................................. 34
6. EXPLODED VIEWS
6-1. Front Cabinet Section ............................................................ 35
6-2. Rear Cabinet Section ............................................................. 36
6-3. CD Section ............................................................................ 38
6-4. Mechanism Deck Section-1 .................................................. 39
6-5. Mechanism Deck Section-2 .................................................. 40
6-6. Optical Pick-up Block ........................................................... 42
7. ELECTRICAL PARTS LIST
......................................
43
Page of 38

Download Sony CFD-101 Service Manual (Repair Manual)

Here you can view online or download Sony CFD-101 Service Manual in pdf. This Service Manual can help you recover, restore, fix, disassemble and repair Sony CFD-101 Audio. Information contained in Sony CFD-101 service manual (repair manual) typically includes:

  • Disassembly, troubleshooting, programming, maintenance, remote, adjustment, installation and setup instructions.
  • Schematics, wiring and block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Parts list (bill of materials).