CDP-XE570 — Sony Audio Service Manual (repair manual)

Model
CDP-XE570
Pages
29
Size
5.62 MB
Type
PDF
Document
Service Manual
Brand
Device
Audio
File
cdp-xe570.pdf
Date

View Sony CDP-XE570 Service Manual online

CDP-XE570
AEP Model
UK Model
SERVICE MANUAL
COMPACT DISC PLAYER
Sony Corporation
Audio Entertainment Group
General Engineering Dept.
9-873-878-11
2001C1600-1
© 2001.3
SPECIFICATIONS
Ver 1.0  2001. 03
Model Name Using Similar Mechanism
NEW
CD Mechanism Type
CDM66-5BD27
Base Unit Type
BU-5BD27
Optical Pick-up Type
PXR-104X
Compact disc player
Laser
Semiconductor laser (
λ
 =
780 nm)
Emission duration:
continuous
Frequency response
2 Hz to 20 kHz 
±
 0.5 dB
Dynamic range
More than 93 dB
Harmonic distortion
0.0045%
Outputs
ANALOG
OUT
DIGITAL
OUT
(OPTICAL)
PHONES
General
Power requirements
230 V AC, 50/60 Hz
Power consumption
11 W
Dimensions (approx.)
430 x 95 x 290 mm
(w/h/d)
incl. projecting parts
Mass (approx.)
3.3 kg
Supplied accessories
Audio cord (2 phono plugs – 2 phono plugs)  (1)
Remote commander (remote) (1) 
R6 (size AA) batteries (2) 
Design and specifications are subject to change
without notice.
Load
impedance
Over 10
kilohms
Wave length:
660 nm
32 ohms
Jack
type
Phono
jacks
Optical
output
connector
Stereo
phone
jack
Maximum
output level
2 V
(at 50
kilohms)
–18 dBm
10 mW
Photo : BLACK
2
CDP-XE570
The following caution label is located inside of the unit.
This appliance is classified
as a CLASS 1 LASER
product.
The CLASS 1 LASER
PRODUCT MARKING is
located on the rear exterior.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
 damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
 circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
 or unsoldering.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 
0
 OR DOTTED LINE WITH
MARK 
0
 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
MODEL IDENTIFICATION
— BACK PANEL —
Parts No.
1. SERVICING NOTE
·························································· 3
2. GENERAL
·········································································· 6
3. DISASSEMBLY
3-1.
Loading Panel ····································································· 7
3-2.
Base Unit (BU-5BD27) ······················································ 7
4. TEST MODE
4-1.
Check Mode ······································································· 8
4-2.
AFADJ Mode ····································································· 8
4-3.
ADJ Mode ·········································································· 9
5. ELECTRICAL BLOCK CHECKING
························ 10
6. DIAGRAMS
6-1.
Circuit Boards Location ··················································· 12
6-2.
Schematic Diagram   Loading Motor Section ·················· 13
6-3.
Printed Wiring Board  Loading Motor Section ················ 13
6-4.
Printed Wiring Board  BD Section ··································· 14
6-5.
Schematic Diagram  BD Section ······································ 15
6-6.
Printed Wiring Board  Main Section ································ 16
6-7.
Schematic Diagram  Main Section ··································· 17
6-8.
Printed Wiring Board  Display Section ···························· 18
6-9.
Schematic Diagram  Display Section ······························· 19
6-10. IC Pinfunctions ································································· 20
6-11. IC Block Diagrams ··························································· 21
7. EXPLODED VIEWS
7-1.
Front Panel and Case Section ··········································· 23
7-2.
CD Mechanism Section (CDM66-5BD27) ······················ 24
7-3.
Base Unit Section (BU-5BD27) ······································· 25
8. ELECTRICAL PARTS LIST
······································· 26
TABLE OF CONTENTS
PARTS No.
MODEL
4-232-150-0s
4-232-150-1s
AEP
UK
3
CDP-XE570
SECTION  1
SERVICING NOTE
HOW TO OPEN THE DISC TRAY WHEN POWER SWITCH
TURNS OFF
Insert a tapering driver into the aperture of the unit bottom, and turn
in the direction of arrow.
Use a flat (–) head screwdriver to open the CD tray by manual opera-
tion. (Flat head screwdriver with nominal blade length of 3mm.)
*
To close the disc table, turn the driver in the reverse direction.
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
The laser diode in the optical pick-up block may suffer
electrostatic breakdown because of the potential difference
generated by the charged electrostatic load, etc. on clothing and
the human body.
During repair, pay attention to electrostatic breakdown and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused
on the disc reflective surface by the objective lens in the optical
pick-up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
Pull out disc table.
4
CDP-XE570
Restrictions in CD-TEXT Display
In this unit, some special characters will not be displayed properly. These will be displayed as a space or a character resembling it. For details,
refer to “Table 2 : CD-TEXT DISC Recorded Contents and Display”.
Table 1 : CD-TEXT TEST DISC TEXT Data Contents (TRACKS No. 1 to 41:Normal Characters)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
TRACK
No.
Displayed Contents
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
TRACK
No.
Displayed Contents
1kHz/0dB/L&R
20Hz/0dB/L&R
40Hz/0dB/L&R
100Hz/0dB/L&R
200Hz/0dB/L&R
500Hz/0dB/L&R
1kHz/0dB/L&R
5kHz/0dB/L&R
7kHz/0dB/L&R
10kHz/0dB/L&R
16kHz/0dB/L&R
18kHz/0dB/L&R
20kHz/0dB/L&R
1kHz/0dB/L&R
1kHz/-1dB/L&R
1kHz/-3dB/L&R
1kHz/-6dB/L&R
1kHz/-10dB/L&R
1kHz/-20dB/L&R
1kHz/-60dB/L&R
1kHz/-80dB/L&R
1kHz/-90dB/L&R
Infinity Zero w/o emphasis//L&R
Infinity Zero with emphasis//L&R
400Hz+7kHz(4:1)/0dB/L&R
400Hz+7kHz(4:1)/-10dB/L&R
19kHz+20kHz(1:1)/0dB/L&R
19kHz+20kHz(1:1)/-10dB/L&R
100Hz/0dB/L*
1kHz/0dB/L*
10kHz/0dB/L*
20kHz/0dB/L*
100Hz/0dB/R*
1kHz/0dB/R*
10kHz/0dB/R*
20kHz/0dB/R*
100Hz  Squer Wave//L&R
1kHz  Squer Wave//L&R
1kHz  w/emphasis/-0.37dB/L&R
5kHz  w/emphasis/-4.53dB/L&R
16kHz  w/emphasis/-9.04dB/L&R
NOTE : The contents of Track No. 1 to 41 are the same as those of the current TEST DISC-their titles are displayed.
However, only 8 digits are displayed, and the 9th digit onwards are displayed as “– – – – –”.
CD-TEXT TEST  DISC
This unit is able to display the TEXT data (character information)
written in the CD on its fluorescent indicator tube.
The CD-TEXT TEST DISC (TGCS-313: J-2501-126-A) is used
for checking the display.
To check, perform the following procedure.
Procedure:
1.
Turn ON the power and set the test disc.
2.
Press the  H  button and play back the disc.
3.
The following will be displayed on the fluorescent indicator
tube.
Display : 1kHz/0 dB/– – – –
4.
Rotate the  l  AMS  L  knob to switch the track. The
text data of each track will be displayed.
5
CDP-XE570
! ” # $ % & ´
(21h to 27h)1kHz 0dB L&R
(   )
+ , – . /
(28h to 2Fh)
0 1 2 3 4 5 6 7
(30h to 37h)
8 9 : ; < = > ?
(38h to 3Fh)
@A B C D E F G
(40h to 47h)
H I J K L M N O
(48h to 4Fh)
P Q R S T U V W
(50h to 57h)
X Y Z [ ¥ ] ^ _
(58h to 5Fh)
a b c d e f g
(60h to 57h)
h i j k l m n o
(68h to 6Fh)
p q r s t u v w
(70h to 77h)
x y z { I }
(78h to 7Fh)
i ¢ £ ¤ ¥
§
(A0h to A7h) 8859-1
9 C
ª
¬
PR
(A8h to AFh)
±
2
3
µ
¶ •
(B0h to B7h)
1
º
¿
(B8h to BFh)
À Á Â Ã Ä Å ÆÇ
(C0h to C7h)
Ƞɠʠˠ̠͠ΠÏ
(C8h to CFh)
D Ñ Ò Ó Ô Õ Ö
(D0h to C7h)
ؠ٠ڠ۠ܠY
ß
(D8h to DFh)
à á â ã ä å æ ç
(E0h to E7h)
è é ê ë ì í î ï
(E8h to FFh)
ñ ò ó ô õ ö
÷
(F0h to F7h)
ø ù ú û ü y
ÿ
(F8h to FFh)
No.66
No.67
  to
No.99
TRACK
No.
Recorded contents
Display
···· ! ” # $ % &
 are not displayed
( )
+
/ ···· , . 
 are not displayed
0 1 2 3 4 5 6 7 ····
8 9
=
? ···· : ; < >
 are not displayed
A B C D E F G ···· @
 is not displayed
H I J K L M N O ····
P Q R S T U V W ····
X Y Z [ / ] ^ _ ····
A B C D E F G ····
H I J K L M N O ····
P Q R S T U V W ····
X Y Z
···· { I }
 
are not displayed
···· 
 
i ¢ £ ¤ ¥   §
 are not displayed
¬
– ···· 
9 C 
ª
   P R are not displayed
±
···· 
2
 
3
 
 
µ 
¶ •
 are not displayed
¿ ···· †
 1 
º 
 
are not displayed
À Á Â Ã Ä Å
···· Æ Ç 
are not displayed
Ƞɠʠˠ̠͠ΠϠ····
Ñ Ò Ó Ô Õ Ö
····D
 are not displayed
Ù Ú Û Ü Y
····Ø   ß 
are not displayed
À Á Â Ã Ä Å
····æ ç 
are not displayed
Ƞɠʠˠ̠͠ΠϠ····
Ñ Ò Ó Ô Õ Ö
····
∂ ÷
 are not displayed
Ù Ú Û Ü Y
···ø ÿ
 are not displayed
T All the same
T All the same
to
T All the same
*
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
to
99
~
1
4
1
2
3
4
˙
1
4
1
2
3
4
Table 2:
CD-TEXT TEST DISC Recorded Contents and Display
(In this unit, some special characters cannot be displayed. This is not a fault.)
´
*
~
´
´
.
...

Download Sony CDP-XE570 Service Manual (Repair Manual)

Here you can view online or download Sony CDP-XE570 Service Manual in pdf. This Service Manual can help you recover, restore, fix, disassemble and repair Sony CDP-XE570 Audio. Information contained in Sony CDP-XE570 service manual (repair manual) typically includes:

  • Disassembly, troubleshooting, programming, maintenance, remote, adjustment, installation and setup instructions.
  • Schematics, wiring and block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Parts list (bill of materials).