Sony CDP-XA30ES Service Manual ▷ View online
– 25 –
Pin No. Pin Name
I/O
Function
75
SBSO
O
Sub-code P-W serial data output terminal Not used (open)
76
EXCK
I
Sub-code P-W serial data reading clock signal input terminal Not used (fixed at “L”)
77
SUBQ
O
Sub-code Q data signal output to the system controller (IC351)
78
SQCK
I
Sub-code Q data reading clock signal input from the system controller (IC351)
79
MUTE
I
Mute signal input from the system controller (IC351)
80
SENS
O
Internal status (SENSE) signal output to the system controller (IC351)
81
XRST
I
System reset signal input from the reset signal generator (IC206) “L”: reset
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
82
DIRC
I
1-track jump mode input terminal Not used (fixed at “H”)
83
SCLK
I
Sense serial data reading clock signal input from the system controller (IC201)
84
DFSW
I
Defect on/off select signal input terminal Not used (fixed at “L”)
85
ATSK
I
Input terminal for the anti-shock Not used (fixed at “L”)
86
DATA
I
Serial data input from the system controller (IC351)
87
XLAT
I
Serial data latch pulse signal input from the system controller (IC351)
88
CLOK
I
Serial data transfer clock signal input from the system controller (IC351)
89
COUT
O
Track number count signal output terminal Not used (open)
90
DVDD
—
Power supply terminal (+5V) (digital system)
91
MIRR
O
Mirror detection signal output terminal Not used (open)
92
DFCT
O
Defect signal output terminal Not used (open)
93
FOK
O
Focus OK signal output terminal Not used (open)
94
FSW
O
Selection signal output terminal of the output filter for spindle motor Not used (open)
95
MON
O
Spindle motor on/off control signal output terminal Not used (open)
96
MDP
O
Spindle servo control signal output terminal
97
MDS
O
Spindle servo control signal output terminal Not used (open)
98
LOCK
O
GFS is sampled by 460 Hz “H” output when GFS is “H” Not used (open)
99
SSTP
I
Detection input from the sled limit-in detect switch (SW102)
The optical pick-up is inner position when “H”
The optical pick-up is inner position when “H”
100
SFDR
O
Sled servo drive PWM signal (+) output to the BA6297AFP (IC102)
– 26 –
Pin No.
Pin Name
I/O
Function
1
A3
O
2
A4
O
3
A5
O
4
A6
O
5
A7
O
6
A8
O
7
A9
O
8
A10
O
9
A11
O
10
A12
O
11
WE
O
Write enable signal output to the static RAM (IC352)
12
NC
O
Not used (open)
13
NC
O
Not used (open)
14
LED-PLAY
O
( LED (D871) drive signal output terminal “H”: LED on
15
LED-PAUSE
O
P LED (D872) drive signal output terminal “H”: LED on
16
LED-FILTER
O
FILTER LED (D873) drive signal output terminal “H”: LED on
17
SPDL-MUTE
O
Mute signal output to the spindle motor driver (IC102, 104)
18
SHIFT-ON/OFF
O
Reset signal output to the CXD2562Q-CS (IC302) “L”: reset
19
VOL UP
O
Volume up control signal output to the volume control motor driver (IC354)
20
VOL DOWN
O
Volume down control signal output to the volume control motor driver (IC354)
21
BLANK
O
Blank signal output to the fluorescent indicator tube driver (IC801 to IC803)
22
FL D0
O
Serial data output to the fluorescent indicator tube driver (IC803)
23
FL D1
O
Serial data output to the fluorescent indicator tube driver (IC802)
24
FL D2
O
Serial data output to the fluorescent indicator tube driver (IC801)
25
FL CLK
O
Serial data transfer clock signal output to the fluorescent indicator tube driver (IC801 to IC803)
26
FL WR
O
Read/write select signal output to the fluorescent indicator tube driver (IC801 to IC803)
27
SENSER SW
O
On/off control signal output to the stabilizer detect sensor (IC361) “H”: on
28
SENSER
I
Detect signal input from the stabilizer detect sensor (IC361) “H”: on
29
LIMIT OUT
I
Detection input from the sled limit-out detect switch
The optical pick-up is outer position when “L” Not used (fixed at “L”)
The optical pick-up is outer position when “L” Not used (fixed at “L”)
30
RESET
I
System reset signal input from the reset signal generator (IC206) “L”: reset
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
31
XTALI
I
Main system clock input terminal (4 MHz)
32
XTALO
O
Main system clock output terminal (4 MHz)
33
VSS
—
Ground terminal
34
TX
O
Sub system clock output terminal Not used (open)
35
TEX
I
Sub system clock input terminal Not used (fixed at “L”)
36
AVSS
—
Ground terminal (for A/D converter)
37
AVREF
I
Reference voltage input terminal (+5V)
38
ADJ/AFADJ
I
Setting terminal for the test mode “L” active
39
K0
I
Key input terminal (A/D input) (fixed at “H”)
40
K1
I
Key input terminal (A/D input)
P MODE, TIME keys (S819S820) input
P MODE, TIME keys (S819S820) input
41
K2
I
Key input terminal (A/D input)
ERASE, CHECK, CLEAR, FILTER,
ERASE, CHECK, CLEAR, FILTER,
0, ) , keys (S801 to S806) input
Address signal output to the static RAM (IC352)
•
BD BOARD IC351 CXP84124-068Q (SYSTEM CONTROL)
– 27 –
Pin No.
Pin Name
I/O
Function
42
K3
I
Key input terminal (A/D input) EDIT/TIME FADE, REPEAT, FILE,
§ OPEN/CLOSE, (, P, p keys (S811 to S817) input
§ OPEN/CLOSE, (, P, p keys (S811 to S817) input
43
K4
I
Rotary encoder input terminal (A/D input) AMS
± key (RV801) input
44
K5
I
Rotary encoder input terminal (A/D input) AMS
≠ key (RV801) input
45
IN/OUT SW
I
Detection input from the loading in/out detect switch (S281, S282) (A/D input)
46
SCLK
O
Sense serial data reading clock signal output to the CXD2545Q (IC101)
47
PRGL
O
Serial data latch pulse signal output to the CXD8595Q (IC301)
48
CLK
O
Serial data transfer clock signal output to the CXD2545Q (IC101) and CXD8595Q (IC301)
49
SENSE
I
Internal status (SENSE) signal input from the CXD2545Q (IC101)
50
DATA
O
Serial data output to the CXD2545Q (IC101) and CXD8595Q (IC301)
51
SQCK
O
Sub-code Q data reading clock signal output to the CXD2545Q (IC101)
52
SUBQ
I
Sub-code Q data signal input from the CXD2545Q (IC101)
53
TEST
O
Output terminal for the test Not used (open)
54
SEL1
I
Destination setting terminal (fixed at “L”)
55
SEL0
I
Destination setting terminal (fixed at “L”)
56
RMIN
I
Remote control signal input from the remote control receiver (IC804)
57
TIMER
I
Timer control input terminal Not used (fixed at “H”)
58
TEST
O
Output terminal for the test Not used (open)
59
TEST
O
Output terminal for the test Not used (open)
60
SCOR
I
Sub-code sync (S0+S1) detection signal input from the CXD2545Q (IC101)
61
AMUTE
O
Muting control signal output to the analog mute driver and mute relay driver
62
LDON
O
Laser diode on/off selection signal output to the RF amplifier in optical pick-up
63
XLT
O
Serial data latch pulse signal output to the CXD2545Q (IC101)
64
LOAD OUT
O
Loading motor (M2) drive signal output to the NJM4558 (IC182) *1
65
LOAD IN
O
Loading motor (M2) drive signal output to the NJM4558 (IC182) *1
66
DOUT
O
Digital out on/off control signal output to the CXD2545Q (IC101) Not used (Open)
67
DMUTE
O
Muting control signal output to the CXD2545Q (IC101) and CXD8595Q (IC301)
68
D0
I/O
69
D1
I/O
70
D2
I/O
71
D3
I/O
72
VDD
—
Power supply terminal (+5V)
73
NC
I
Not used (fixed at “H”)
74
D4
I/O
75
D5
I/O
76
D6
I/O
77
D7
I/O
78
A0
O
79
A1
O
Address signal output to the static RAM (IC352)
80
A2
O
Two-way data bus with the static RAM (IC352)
Two-way data bus with the static RAM (IC352)
*1 Loading motor (M2) control
LOAD OUT (pin ^¢)
“L”
“H”
“L”
“H”
LOAD IN (pin ^∞)
“L”
“L”
“H”
“H”
OFF
OUT
I N
BRAKE
Operation
Terminal
– 28 –
Main Ports
SPDL-MUTE (pin !¶)
From the viewpoint of performance of the set, the disc must
not move nor sway when the disc table opens.
From the viewpoint of performance of the set, the disc must
not move nor sway when the disc table opens.
These
problems however occur in the actual case due to the offset
voltage generated and the voltage generated because of the
positional relation between the BSL coil and Hall element.
The spindle motor driver (IC102, IC104) is therefore muted
while the tray is open. Pin !¶ provides the timing for this.
voltage generated and the voltage generated because of the
positional relation between the BSL coil and Hall element.
The spindle motor driver (IC102, IC104) is therefore muted
while the tray is open. Pin !¶ provides the timing for this.
H
L
OPEN
Reverses after a
certain period of time.
certain period of time.
SP MUTE
(MUTE ON)
CLOSE
SPINDLE
KICK
Reverses after a
certain period of time.
certain period of time.
PLAY
Time while the
disc can be seen
(Estimate).
disc can be seen
(Estimate).
The spindle
motor driver is
muted during
this time.
motor driver is
muted during
this time.
BLANK (pin @¡)
This port is required because the display tube in this set static
lights
This port is required because the display tube in this set static
lights
up and a dedicated screwdriver is required. It is
basically a RESET pin.
But as problems will occur if used
also as RESET, timings are specially provided using the
micro-processor.
micro-processor.
SENSER (pin @•)
The results of the detection of IC361 IS471F is output to this
pin. It becomes “ L” when there is no stabilizer (when light
reaches). The next process of imposing the next focus is not
performed. (Effective only when pin @¶ is “H”.)
Therefore, it must be noted that if PLAY is performed when th
servo board at the top of the CDM is not assembled properly,
the detection circuit operates and this pin does not operate.
It is does not operate, refer to 1. SERVICING NOTES ” Prep-
arations for Adjustment and Measurement” on page 3.
The results of the detection of IC361 IS471F is output to this
pin. It becomes “ L” when there is no stabilizer (when light
reaches). The next process of imposing the next focus is not
performed. (Effective only when pin @¶ is “H”.)
Therefore, it must be noted that if PLAY is performed when th
servo board at the top of the CDM is not assembled properly,
the detection circuit operates and this pin does not operate.
It is does not operate, refer to 1. SERVICING NOTES ” Prep-
arations for Adjustment and Measurement” on page 3.
GLout pin
output waveform
output waveform
SENSER SW (pin
@¶)
As IC361 IS471F operate in pulse as shown in the figure, the
sound quality may be affected if operated constantly.
sound quality may be affected if operated constantly.
As the
purpose of IC361 is to detect if the presence of the stabilizer,
it should be operated only when the tray is drawn in. IC361
operates as it is “H” only at this time. Normally it is “L”.
it should be operated only when the tray is drawn in. IC361
operates as it is “H” only at this time. Normally it is “L”.
Ee
0
Eep
Eed
Time
Eep is the luminance of the signal light tuned with the low
level timing of the GLout pin output.
Eed is the luminance of the D.C. light.
level timing of the GLout pin output.
Eed is the luminance of the D.C. light.
The light source is
the infrated-emitting diode (
λ
p=940 nm).
*
Click on the first or last page to see other CDP-XA30ES service manuals if exist.