Sony CDP-M400CS Service Manual ▷ View online
9
CDP-M400CS
3-4. TRANS BOARD
3-5. IR-IN BOARD
5
screw (BVTP 3
×
8)
6
bracket (PT)
4
connector
(CN601)
(CN601)
1
connector
(CN991)
(CN991)
3
connector (CN603)
2
connector
(CN602)
(CN602)
7
two screws
(PTTWH 3
(PTTWH 3
×
6)
8
TRANS board
a
a
1
two screws
(BVTP 3
(BVTP 3
×
8)
2
IR-IN board
10
CDP-M400CS
3-6. FRONT PANEL ASSEMBLY
3-7. JOG BOARD, DISP BOARD, KEYBOARD BOARD
2
3
connector (CNP503)
5
two screws
(BVTP 3
(BVTP 3
×
8)
4
screw
(BVTP 3
(BVTP 3
×
8)
6
three screws
(BVTP 3
(BVTP 3
×
8)
7
remove the claw
8
remove the claw
9
front panel assembly
1
qs
Remove two solderings.
1
knob (AMS)
2
knob (disc)
3
four screws
(BVTP 2.6
(BVTP 2.6
×
8)
4
bracket (case)
assembly
assembly
5
eleven screws
(BVTP 2.6
(BVTP 2.6
×
8)
7
eight screws
(BVTP 2.6
(BVTP 2.6
×
8)
qa
two screws
(BVTP 2.6
(BVTP 2.6
×
8)
8
DISP board
9
flat type wire
(17 core)
(17 core)
0
knob
(timer)
(timer)
6
JOG board
qf
KEYBOARD
board
board
qd
bracket (keyboard)
11
CDP-M400CS
3-8. COVER (PT), TABLE (400) ASSEMBLY
3-9. LED BOARD, GUIDE (DOOR)
3
screw (BVTP 3
×
16)
4
guide (door)
5
table (400) assembly
6
washer
Note during re-assembling
When re-assembling, align
the positions as shown.
the positions as shown.
1
two screws
(BVTP 3
(BVTP 3
×
8)
2
cover (PT)
1
screw (BVTP 3
×
8)
6
window (internal illumination)
2
LED board
3
5
4
7
guide (door)
12
CDP-M400CS
3-10. DOOR SW BOARD
5
two screws
(BVTP 2.6
(BVTP 2.6
×
8)
3
screw (PTPWH 2.6
×
8)
1
screw (PTPWH 2.6
×
8)
1
Move the slider (pop-up) and the lever (pu joint) fully
in the direction of the arrow
in the direction of the arrow
A
.
2
Install the gear (cam) in the direction shown
in the illustration and rotate it fully
in the direction of the arrow
in the illustration and rotate it fully
in the direction of the arrow
B
.
3
When the gear (cam) happens to go too deep,
return it to the original position
in the direction of the arrow
return it to the original position
in the direction of the arrow
C
.
4
gear (B)
2
gear (cam)
6
DOOR SW board
C
B
A
lever (pu joint)
two rotary switches
slider (pop-up)
gear (cam)
DOOR SW board
The levers of the two rotary switches on the D. SW board
are shown in the illustration below.
are shown in the illustration below.
Precaution during the gear (cam) installation
Click on the first or last page to see other CDP-M400CS service manuals if exist.