Sony CDP-M400CS Service Manual ▷ View online
21
CDP-M400CS
1.
Disc change
2.
Load in
3.
TOC read
4.
Access of last track
5.
3 second playback
6.
Access of first track
7.
3 second playback
8.
Load out
1.
No. 80
2.
No. 320
3.
No. 240
4.
No. 400
5.
No. 160
Sequence of Aging Mode
$
$
$
$
$
$
$
$
$
Order of Disc Change
(1 cycle takes 3 minutes)
$
$
$
$
$
$
SOFT WARE VERSION DISPLAY
• Software version can be displayed on the fluorescent indicator
tube.
Procedure:
With the power ON, while pressing the TIME and MEGA
CONTROL buttons, press the
With the power ON, while pressing the TIME and MEGA
CONTROL buttons, press the
1/u button.
Rotate the DISC/ALBUM/CHARACTER dial, select “Version”
and press the dial.
Software version is displayed on the fluorescent indicator tube.
and press the dial.
Software version is displayed on the fluorescent indicator tube.
To end this mode, press the
1/u button.
BU TEST MODE
•
This mode is used for electrical adjustments.
Refer to the section on Electrical Adjustment.
Refer to the section on Electrical Adjustment.
CDM TEST MODE
•
This mode is used for mechanical adjustments and electrical
adjustments.
Refer to the section on Mechanical adjustment and Electrical
Adjustment.
adjustments.
Refer to the section on Mechanical adjustment and Electrical
Adjustment.
AGING MODE
•
Mode which repeatedly changes and plays back discs
automatically in the unit.
automatically in the unit.
•
It will repeat aging as long as no errors occur.
•
If an error occurs during aging, it will stop all servos, motors,
etc. instantaneously, display the error number, and stop
operations.
The function serves to maintain the state of the unit when errors
occur.
etc. instantaneously, display the error number, and stop
operations.
The function serves to maintain the state of the unit when errors
occur.
Special Aging Mode Functions
The aging mode is provided with the following convenient functions
1. Disc setting mode:
5 discs are set before setting the aging mode. This mode makes
the setting of these discs more easy.
the setting of these discs more easy.
2. Aging disc count function:
Functions which displays the number of aging discs carried
out on the Fluorescent indicator tube in numbers.
out on the Fluorescent indicator tube in numbers.
Aging Procedure
1. Turn on the power and press the TIME , MEGA CONTROL
and
1/u buttons.
2. Rotate DISC/ALBUM/CHARACTER dial, select “Aging
Mode” and press the dial to start the aging mode.
3. When the disc set mode is set, the
· and P LEDs blink.
4. Rotate the DISC/ALBUM/CHARACTER dial. The slits (No.
80, 160, 240, 320, 400) for setting the discs will come forward.
Insert the discs into these slits. Do not set the discs in other
slits.
Insert the discs into these slits. Do not set the discs in other
slits.
5. Press the
· button.
6. The
· LED blinks, the aging mode is set, and aging is
started.
7. The aging cycle lasts 3 minutes. If errors occur during aging,
the error number will be displayed on the Fluorescent indicator
tube. (Refer to the following table for the details of the errors.)
tube. (Refer to the following table for the details of the errors.)
8. Aging will be repeated as long as no errors occur.
9. After disc load out, the number displayed on the Fluorescent
9. After disc load out, the number displayed on the Fluorescent
indicator tube will increase.
10. To end aging, press the
1/u button.
If an error occurs and the
1/u button is useless, disconnect
the power cord from the outlet.
Display in aging cycle
AGED 10
DISC 180
22
CDP-M400CS
Error Display
1. Disc sensor error
Error code
2. Mechanism error
Error code 1
X : negligible number
Error code 2
X : negligible number
Error code 3
X : negligible number
Error code 4
X : negligible number
3. BD error
1 2 0
1 2 3 4
Disc number
with error
alternating
Aging counter
Y
1 2
3 4
5 6
7 8
1 2 3 4
Error code1
Error code2
Error code3
Error code4
alternating
Aging counter
Y
1 2
3 4
5 6
1 2 3 4
The state
during aging
Error code
alternating
Aging counter
Y
Contents
Error during table operation
With no problem
Code number
1X
2X
Contents
With no problem
Error during table operation
Code number
0X
1X
Contents
From chucking to TOC read
From chucking to TOC read
From TOC read to end of last track
playback
From TOC read to end of last track
playback
From end of last track playback to end of
first track playback
From end of last track playback to end of
first track playback
Code number
01
02
03
04
05
06
Contents
With no problem
With no problem
Error during door initialization
Error during loading initialization
Error during door initialization
With no problem
Code number
0X
1X
2X
3X
4X
FX
Contents
No disc in the speified slit, or Disc in the
other slits
Code number
Contents
Error during loading in
Error during loading out
With no problem
With no problem
Code number
1X
2X
3X
4X
23
CDP-M400CS
SHIPMENT MODE
•
This mode is used for setting the unit to the shipment state.
Do not execute it without a proper reason as it erases the
memory of the title memo recorded by the customer.
Do not execute it without a proper reason as it erases the
memory of the title memo recorded by the customer.
Procedure1:
With the power ON, while pressing the TIME button and MEGA
CONTROL button, press the
With the power ON, while pressing the TIME button and MEGA
CONTROL button, press the
1/u button.
Rotate the DISC/ALBUM/CHARACTER dial, select “Ship Mode”
and press the dial. “-OFF-” is displayed and the standby mode is
automaticaly entered.
and press the dial. “-OFF-” is displayed and the standby mode is
automaticaly entered.
Procedure2:
With the power ON, while pressing the ARTIST MODE button
and H button, press the +100 button. “-OFF-” is displayed and
the standby mode is automatically entered.
With the power ON, while pressing the ARTIST MODE button
and H button, press the +100 button. “-OFF-” is displayed and
the standby mode is automatically entered.
DOOR POP UP AGING MODE
•
This mode is used for performing aging of the CD pop up part
and door open/close.
It is used for checking if operations are performed normally.
and door open/close.
It is used for checking if operations are performed normally.
Procedure1:
1. With the power ON, while pressing the TIME button and
MEGA CONTROL button, press the
1/u button.
2. Rotate the DISC/ALBUM/CHARACTER dial, select “CDM
Test”and press the dial.
3. Rotate the DISC/ALBUM/CHARACTER dial, select
“DoorPopup Aging” and press the dial.
4. Aging starts, and door open/close and up/down operations of
the pop up part are performed continuously.
5. To end this mode, press the
1/u button.
Procedure2:
1. With the power ON, while pressing the TOP ARTIST 3 button
and
· button, press the +100 button.
2. Aging starts, and door open/close and up/down operations of
the pop up part are performed continuously.
3. To end the mode, press the
1/u button.
ALL LIT MODE
•
This mode is used for lighting the whole fluorescent indicator
tubes and LEDs.
tubes and LEDs.
Procedure:
With the power ON, while pressing the TOP ARTIST4 and
With the power ON, while pressing the TOP ARTIST4 and
·
buttons, press the +100 button.
Both the fluorescent indicator tubes and LEDs will light up
completely.
To end this mode, press the
Both the fluorescent indicator tubes and LEDs will light up
completely.
To end this mode, press the
1/u button.
MODEL NAME DISPLAY
•
Model names can be displayed on the fluorescent indicator
tube for checking the microprocessor model setting, etc.
tube for checking the microprocessor model setting, etc.
Procedure:
With the power ON, while pressing the TOP ARTIST6 and
With the power ON, while pressing the TOP ARTIST6 and
·
buttons, press the +100 button.
The model name is displayed on the fluorescent indicator tube.
To end this mode, press the
The model name is displayed on the fluorescent indicator tube.
To end this mode, press the
1/u button.
SPRAY MODE
•
This mode is used for the electrical adjustments.
Refer to the sedtion on Electrical Adjustment.
Refer to the sedtion on Electrical Adjustment.
24
CDP-M400CS
A B C D E F G
ADJ Mode
1. Turn ON the power of the unit, set disc to disc table, and
perform chucking.
2. Disconnect the power supply plug from the outlet.
3. To set ADJ mode, connect the test point (ADJ) of the MAIN
3. To set ADJ mode, connect the test point (ADJ) of the MAIN
board to Ground, and connect the power supply plug to the
outlet.
outlet.
In this mode, table rotation and loading operations are not performed
because it is taken that the disc has already been chucked.
because it is taken that the disc has already been chucked.
Note: The same operations are also performed in the following
when the test point (ADJ) is connected to Ground after turning
on the power.
when the test point (ADJ) is connected to Ground after turning
on the power.
•
Direct search (movement of sledding motor) is not performed
during accessing
during accessing
•
Ignored even when GFS becomes L
•
Ignored even when the Q data cannot be read
•
Focus gain does not decrease
Key and Display Check Mode
To set this mode, connect the test point (AFADJ) on the MAIN
board to Ground, and connect the power supply plug to the outlet.
board to Ground, and connect the power supply plug to the outlet.
Note: When this mode is executed, all title memos recorded will
be erased.
be erased.
•
When this button is pressed, “line # No. #” will be displayed.
However, these will not be displayed for the following special
buttons. However, these will not be displayed for the following
special buttons.
However, these will not be displayed for the following special
buttons. However, these will not be displayed for the following
special buttons.
x (stop) button: FL segment check
(Refer to FL Tube Check Patterns)
P (pause) button: FL grid check
(Refer to FL Tube Check Patterns)
The
The
P LED also lights up simultaneously.
· (play) button: All FL segment and grid will light up.
· LED also lights up simultaneously.
TIMER switch: When the switch position is PLAY , the
STANDBY LED lights up. It goes OFF when
set to OFF .
set to OFF .
Each time this button is pressed, the value of the “Got ## keys”
increases. Buttons pressed once will not be counted when pressed
again.
increases. Buttons pressed once will not be counted when pressed
again.
FL Tube Check Patterns
Segment check
Grid check
•
When the jog dial and AMS is rotated to the right, the TOP
ARTIST LEDs light up in the order of 8
ARTIST LEDs light up in the order of 8
n 7..1 n HISTORY
ALBUM SELECT
n MEGA CONTROL n X n H n
ARTIST MODE
n 8.
•
When the jog dial and AMS is rotated to the left, the TOP
ARTIST LEDs light up in the order of 1
ARTIST LEDs light up in the order of 1
n 2..8 n ARTIST
MODE
n H n X n MEGA CONTROL ALBUM
SELECT
n HISTORY n 1.
•
Abbreviation
FL: Fluorescent Indicator Tube
FL: Fluorescent Indicator Tube
To end the ADJ mode
1. Disconnect the plug.
2. Remove the wire between AFADJ and GND.
2. Remove the wire between AFADJ and GND.
Adjustment Location: MAIN board (See page 28)
To end the ADJ mode
1. Press the
1/u button and disconnect the plug.
2. Remove the wire between ADJ and GND.
Magnified
Click on the first or last page to see other CDP-M400CS service manuals if exist.