Sony BDV-NF620 / BDV-NF720 / HBD-NF620 / HBD-NF720 Service Manual ▷ View online
HBD-NF620/NF720
9
CHECKING METHOD OF NETWORK OPERATION
(NF720 only)
It is necessary to check the network operation, when replacing the
MB-149 board or wireless LAN card (WLC1). Check the operation
of wireless and wired LAN, according to the following method.
(NF720 only)
It is necessary to check the network operation, when replacing the
MB-149 board or wireless LAN card (WLC1). Check the operation
of wireless and wired LAN, according to the following method.
1. Checking Method of Wireless LAN Operation
Check that access point is recognized surely.
Check that access point is recognized surely.
Necessary Equipment:
Wireless access point with router function (AP)
Wireless access point with router function (AP)
Procedure:
1. Press the [HOME] button on the remote commander to enter
1. Press the [HOME] button on the remote commander to enter
the home menu.
2. Press the [
m]/[M]/[<]/[,] buttons on the remote command-
er to select “Setup”
“Network Settings”, and press the [ ]
button on the remote commander.
3. Select “Internet Settings”, and press the [
] button on the re-
mote commander.
4. Press the [
m]/[M] buttons on the remote commander to select
“Wireless Setup (built-in)”, and press the [
] button on the
remote commander.
5. The system starts searching for access points, and displays a
list of up available network name (SSID).
6. Check that access point (SSID) is displayed on the searching
result.
7. Press the [
?/1
] button to turn the power off.
Note: Refer to the instruction manual about details of the setting method.
2. Checking method of wired LAN operation
Check that access point is recognized surely.
Check that access point is recognized surely.
Procedure:
1. Connect the main unit to the router or the hub, etc. with the
1. Connect the main unit to the router or the hub, etc. with the
LAN cable.
2. Press the [HOME] button on the remote commander to enter
the home menu.
3. Press
the
[
m]/[M]/[<]/[,] buttons on the remote command-
er to select “Setup”
“Network Settings”, and press the [ ]
button on the remote commander.
4. Select “Internet Settings”, and press the [
] button on the re-
mote commander.
5. Press the [
m]/[M] buttons on the remote commander to select
“Wired Setup”, and press the [
] button on the remote com-
mander.
6. Press the [
m]/[M] buttons on the remote commander to select
“Auto”, and press the [
] button on the remote commander.
7. Press the [
,] button on the remote commander.
8. Press the [
m]/[M] buttons on the remote commander to select
“Save & Connect”, and press the [
] button on the remote
commander.
9. When “Internet Settings is now complete.” appears, then press
the [
] button on the remote commander.
10. Press the [HOME] button on the remote commander to enter
the home menu.
11. Press the [
m]/[M]/[<]/[,] buttons on the remote command-
er to select “Setup”
“Network Settings”, and press the [ ]
button on the remote commander.
12. Press the [
m]/[M] buttons on the remote commander to select
“Network Connection Diagnostics”, and press the [
] button
on the remote commander.
13. Press the [
<]/[,] buttons on the remote commander to
select “Start”, and press the [
] button on the remote com-
mander.
14. Confi rm that “Network connections are correct” is displayed.
15. Press the [
15. Press the [
?/1
] button to turn the power off.
Note: Refer to the instruction manual about details of the setting method.
HBD-NF620/NF720
10
HOW TO EJECT THE DISC WHEN POWER SWITCH TURN OFF
NX_AMP BOARD SERVICE POSITION
The BD drive is taken out, and please rotate
the pulley in the direction of the arrow by
screwdriver etc. after detaching and take
out the disc.
the pulley in the direction of the arrow by
screwdriver etc. after detaching and take
out the disc.
disc
– BD drive bottom view –
insulating sheet
NX_AMP board
switching regulator (SWR1)
power cord
HBD-NF620/NF720
11
SECTION 2
DISASSEMBLY
•
This set can be disassembled in the order shown below.
2-1. DISASSEMBLY FLOW
2-2. COVER (TOP) BLOCK
(Page
(Page
12)
SET
2-3. TOUCH
BOARD
(Page
13)
2-4. COVER (BOTTOM) BLOCK
(Page
(Page
14)
2-5. SHIELD (DRIVE) (HBD-NF620)
(Page
(Page
15)
2-6. BD DRIVE (BSX-3)
(Page
(Page
15)
2-7. LED
BOARD
(Page
16)
2-14. SHIELD (PS) BLOCK
(Page
(Page
20)
2-13. OPTICAL PICK-UP
(KEM-480AAA)
(Page
(KEM-480AAA)
(Page
20)
2-12. BOTTOM COVER
(Page
(Page
19)
2-16. BRACKET (PS)
(Page
(Page
22)
2-17. POWER CORD (AC1)
(Page
(Page
22)
2-18. HEAT SINK (AMP)
(Page
(Page
23)
2-19. NX_AMP BOARD
(Page
(Page
23)
2-8. WIRELESS LAN CARD (WLC1) (HBD-NF720)
(Page
(Page
16)
2-9. CHASSIS (MIDDLE) BLOCK
(Page
(Page
17)
2-10. BRACKET (DRIVE)
(Page
(Page
17)
2-11. MB-149 BOARD
(Page
(Page
18)
2-20. HOW TO BEND WIRE (FLAT TYPE)
(Page
(Page
24)
2-15. SWITCHING REGULATOR
(SWR1)
(Page
(SWR1)
(Page
21)
HBD-NF620/NF720
12
Note: Follow the disassembly procedure in the numerical order given.
2-2. COVER (TOP) BLOCK
1 two screws
(BV DIA. 2.6
u 8)
1 five screws
(BV DIA. 2.6
u 8)
1 five screws
(BV DIA. 2.6
u 8)
4 eight claws
5 wire (flat type) (11 core)
(CN700)
wire (flat type)
2 three claws
3 Remove the cover (top) block
in the direction of an arrow.
6 cover (top) block
2 four claws
Note 3: Align this portion into the groove
and align screw boss beneath the
screw
hole.
Note 2: Since the wire (flat type) (11core) is
connected, remove slowly.
screw hole
screw boss
groove
– Rear bottom view –
– Rear top view –
– Rear view –
Note 3: Align this portion into the groove
and align screw boss beneath the
screw
hole.
screw hole
screw boss
groove
– Rear view –
Note 4: When installing the wire (flat type),
ensure the coloured line.
No slanting after insertion.
coloured line
connector
Note 1: Please spread a sheet under a unit
not to injure cover (top).
Click on the first or last page to see other BDV-NF620 / BDV-NF720 / HBD-NF620 / HBD-NF720 service manuals if exist.