Sony BDV-E670W / BDV-E970W / HBD-E970W Service Manual ▷ View online
HBD-E670W/E970W
17
2-12. OPTICAL PICK-UP BLOCK (KEM-460AAA), WIRE (FLAT TYPE)
Note: Please prepare the thin wire (clip etc.).
1
two screws
(BVTP 2.6)
7
two float screws (S)
qa
insulator
5
Insert the thin
wire (clip etc.).
qa
insulator
qa
insulator
qs
optical pick-up block
(KEM-460AAA)
qa
insulator
qd
non-halogene tape
qf
wire (flat type) (5 core)
qk
wire (flat type)
(45 core)
qj
wire (flat type)
(9 core)
loading assy (D)
qh
ffc holder (rear)
2
two claws
6
8
9
qg
0
3
two claws
4
chuck holder assy (D)
– Bottom view –
1
wire (flat type) (45 core)
Fold
Under the guide.
Under the guide.
(Fold area)
(Fold area)
boss
boss
loading assy (D)
terminal face
terminal face
2
Through the hole.
4
Through the hole.
3
wire (flat type) (9 core)
5
ffc holder (rear)
7
two claws
7
three claws
6
,QVWDOODWLRQRIZLUHIODWW\SHFRUHDQGZLUHIODWW\SHFRUH
Note: This illustration sees the loading assy (D) from bottom side.
HBD-E670W/E970W
18
SECTION 3
TEST MODE
COLD RESET
The cold reset clears data except BD/DVD data stored in the RAM
to initial conditions. Execute this mode when returning the set to
the customers.
Procedure:
1. Press the [
The cold reset clears data except BD/DVD data stored in the RAM
to initial conditions. Execute this mode when returning the set to
the customers.
Procedure:
1. Press the [
?/1
] button to turn the power on.
2. Press the [
x
] and [VOLUME –] buttons simultaneously and
hold down (around 5 seconds).
3. The message “COLD RESET” appears on fl uorescent indica-
tor tube, then becomes standby states.
DEMO MODE
This mode let you lock the disc tray. When this mode is activated,
the disc will not eject when the [
This mode let you lock the disc tray. When this mode is activated,
the disc will not eject when the [
Z
] button is pressed. The message
“LOCKED” will be displayed on the fluorescent indicator tube.
Procedure:
1. Press the [
Procedure:
1. Press the [
?/1
] button to turn the power on.
2. Press the [FUNCTION] button to select the “BD/DVD”.
3. Press the [
3. Press the [
x
] and [
Z
] buttons simultaneously and hold down
until “DEMO ON” or “DEMO OFF” displayed on the fluores-
cent indicator tube (around 5 seconds).
cent indicator tube (around 5 seconds).
S-AIR ID SETTING DISPLAY
Procedure:
1. Press the [
Procedure:
1. Press the [
?/1
] button to turn the power on.
2. Press the [FUNCTION] and [VOLUME +] buttons simultane-
ously and hold down (around 5 seconds).
3. S-AIR ID setting is displayed on the fl uorescent indicator tube.
PANEL TEST
Procedure:
1. Press the [
Procedure:
1. Press the [
?/1
] button to turn the power on.
2. Press button in order of the [RETURN]
→ [0] → [0] → [1]
→ [SUBTITLE] on the remote commander (Make the interval
when each button is pressed within two seconds).
when each button is pressed within two seconds).
3. All segments in fl uorescent indicator tube are lighted up. And
half segments in fl uorescent indicator tube are lighted up, oth-
ers half segments in fl uorescent indicator tube are lighted up,
then all segments in fl uorescent indicator tube are lighted up.
This operation is repeated.
ers half segments in fl uorescent indicator tube are lighted up,
then all segments in fl uorescent indicator tube are lighted up.
This operation is repeated.
4. When all segments in fl uorescent indicator tube are lighted up
in the state of step 3, press the [VOLUME +] button on the
remote commander and model information is displayed on the
fl uorescent indicator tube.
remote commander and model information is displayed on the
fl uorescent indicator tube.
Each time the [VOLUME +] button on the remote commander
is pressed, the display changes from destination information,
STR version, SYS version, UI version, BDLIB version, ST
version, TA version, DSP version, TM version, CEC version,
SAIR version, PF version in this order, and returns to the mod-
el information display.
is pressed, the display changes from destination information,
STR version, SYS version, UI version, BDLIB version, ST
version, TA version, DSP version, TM version, CEC version,
SAIR version, PF version in this order, and returns to the mod-
el information display.
Each time the [VOLUME –] button on the remote commander
is pressed, the version and date are switched.
is pressed, the version and date are switched.
5. In the state of step 3, press the [FUNCTION] button on the
remote commander and “K 0” is displayed on the fluorescent
indicator tube.
indicator tube.
“K 0” value increases whenever a button on the set is pressed.
However, once a button has been pressed, it is no longed taken
into account.
However, once a button has been pressed, it is no longed taken
into account.
All buttons on the set are pressed, “OK” and “K 7” are alter-
nately displayed on the fluorescent indicator tube.
nately displayed on the fluorescent indicator tube.
6. To release from this mode, press the [
?/1
] button.
AMP TEST
Procedure:
1. Press the [
Procedure:
1. Press the [
?/1
] button to turn the power on.
2. Press button in order of the [RETURN]
→ [0] → [1] → [1]
→ [SUBTITLE] on the remote commander (Make the interval
when each button is pressed within two seconds).
when each button is pressed within two seconds).
3. The message “MEASURE” appears on the fluorescent indica-
tor tube and enter the AMP test mode.
4. Press the [BLUE] button on the remote commander, the state
of D.C.A.C. microphone is displayed on the fl uorescent indica-
tor tube.
tor tube.
*** @@ $$$
***
: Either of “IN”/“NON” is displayed by the state of
detection of the microphone.
@@ : Either of “OK”/“NG” is displayed by the state of
digital audio data input.
$$$
: Microphone input audio data A/D value (0 – 255).
5. Press the [MUTING] button on the remote commander, “VOL
N” (The change in the volume is usual)/“VOL MSM” (The
change in the volume is a switch of MIN/1/20/MAX) can be
switched.
change in the volume is a switch of MIN/1/20/MAX) can be
switched.
6. Press the [SUBTITLE] button on the remote commander, the
message “VACS ON” or “VACS OFF” appears on the fl uores-
cent indicator tube and thus the VACS on/off are changed.
cent indicator tube and thus the VACS on/off are changed.
7. To release from this mode, press the [
?/1
] button.
BD SERVICE MODE
Note: The operation in this mode must use a remote commander.
Setting method of the BD service mode:
1. Press the [
1. Press the [
?/1
] button to turn the power on.
2. Press button in order of the [RETURN]
→ [0] → [2] → [1] →
[SUBTITLE] on the remote commander. (Make the interval
when each button is pressed within two seconds)
when each button is pressed within two seconds)
3. Enter the BD service mode.
1. Main Functions
•
•
ErrorLog display
Display the error log. Displayed contents can also be saved in
an USB memory device.
an USB memory device.
• Diag
Performs unit test of devices installed on the board.
•
Factory Initialize
Restores the set to its factory settings.
• Network
Checks the wired network connection.
•
Version Up (version update)
Not used.
•
System Information
Displays the system information of the set.
Displays information such as the software version, drive infor-
mation, etc.
mation, etc.
•
EMC Test Mode
Not used.
• Drive
Write drive OP data and check drive.
HBD-E670W/E970W
19
2. Menu Tree
Service Mode Menu
[1] Diag
[2] Log
[3] Factory Initialize
[4] Network
[5] Version Up
[6] System Information
[1] Diag
[2] Log
[3] Factory Initialize
[4] Network
[5] Version Up
[6] System Information
Service Mode Menu
[1] Diag
[2] Log
[3] Factory Initialize
[4] Network
[5] Version Up
[6] System Information
[7] EMC Test Mode
[8] Drive
[1] Diag
[2] Log
[3] Factory Initialize
[4] Network
[5] Version Up
[6] System Information
[7] EMC Test Mode
[8] Drive
Version Up
Not used
Not used
System Information
Displays system information
Displays system information
Factory Initialize
5estores set to factory settings
5estores set to factory settings
Log
Displays Error Log
Displays Error Log
Error Log
Displays error log
Diag
Network
Network diagnosis for wired
Network diagnosis for wired
Ping
Confirm network connection
Ifconfig
View network status
Device Test
US%D$CIFcon test
US%D$CIFcon test
Video Test
Video output test
Video output test
$udio Test
$udio output test
$udio output test
$udio Input Test
$udio Input Test
$udio Input Test
:ireless L$N Test
Not used
Not used
EMC Test Mode
Not used
Not used
Drive
Write drive OP data and check drive
Write drive OP data and check drive
Start Initialize for TV
Not used
Start Initialize
Initialize default setting for %Dplayer
Diag Test
HBD-E670W/E970W
20
3. Service Mode Menu (Top Menu)
This is the top menu of service mode.
Each function is accessed from this screen.
Operation:
[1]
This is the top menu of service mode.
Each function is accessed from this screen.
Operation:
[1]
Moves to Diag screen
[2]
Moves to Log screen
[3]
Moves to Factory Initialize screen
[4]
Moves to Network screen
[5]
Moves to Version Up (DISC version update) screen (Not
used)
used)
[6]
Moves to System Information screen
[7]
Moves to EMC test mode screen (Not used)
[8]
Moves to Drive screen
[
M
]/[
m
] Moves the cursor
[
3
]
Moves to the screen of the item selected with the cursor
* Cursor is not displayed when the menu is fi rst displayed.
Service Mode Menu
[1] Diag
[2] Log
[3] Factory Initialize
[4] Network
[5] Version Up
[6] System Information
[7] EMC Test Mode
[8] Drive
[3] Factory Initialize
[4] Network
[5] Version Up
[6] System Information
[7] EMC Test Mode
[8] Drive
HELP : [DOWN] [ENT] [(NUM)]
HELP (currently available keys, etc.) is displayed
[1] Diag
4. Diag (Device Test)
This screen is used to test devices mounted on the board.
This screen is used to test devices mounted on the board.
Screen 1: Selects the test category
Operation:
[
Operation:
[
<
]/[
,
] Selects the category
[
m
]/[
3
]
Moves to the selected category
Screen 2: Device test
Selects the device to test after selecting Device Test in screen 1.
Operation:
[
Selects the device to test after selecting Device Test in screen 1.
Operation:
[
<
]/[
,
] Selects the device to test
[
3
]
Executes the test
[
M
]
Returns to selection of test category
•
List of test categories
Device Test
Video Test
Audio Test
Audio Input Test
Wireless LAN Test (not used)
Video Test
Audio Test
Audio Input Test
Wireless LAN Test (not used)
•
Device Test: List of devices
USB Host (*1)
*1) USB media check (front and rear). Only one time.
* For details concerning device test, see the Diag reference.
* For details concerning device test, see the Diag reference.
Diag
Category:
Diag
Category: Device Test
Device:
Rear USB Media check ... OK
Front USB Media check ... OK
Front USB Media check ... OK
Checking...
HELP: [RIGHT] [UP] [ENT] [RET]
USB Host
Device Test
(Screen 1)
(Screen 2)
5. Diag (Video/Audio Test)
This screen performs video and audio tests.
This screen performs video and audio tests.
Screen 1: When video test category is selected
Operation:
[
Operation:
[
3
]
Shows/hides the color bar
[
M
]/[RETURN] Returns to the selection of test category
Screen 2: When audio test category is selected
Operation:
[
Operation:
[
3
]
Plays back/stops the tone sound
[
M
]/[RETURN] Returns to the selection of test category
•
Video test:
Outputs a color bar (composite & component & HDMI).
•
Audio test:
TONE sound output (speaker (8 ch) & HDMI (2 ch)).
Diag
Category: Video Test
HELP: [UP][ENT][RET]
Diag
Category: Audio Test
HELP: [UP] [ENT] [RET]
[ENT] Show Color Bar
[ENT] Generate TONE Sound
(Screen 1)
(Screen 2)
Click on the first or last page to see other BDV-E670W / BDV-E970W / HBD-E970W service manuals if exist.