Sony BDV-E380 / BDV-E580 / BDV-E880 / BDV-E980 / BDV-T58 / HBD-E380 / HBD-E580 / HBD-E880 / HBD-E980 / HBD-T58 Service Manual ▷ View online
HBD-E380/E580/E880/E980/T58
9
NOTE OF REPLACING THE IC3100, IC3200 AND
IC3300 ON THE AMP BOARD AND THE COMPLETE
AMP BOARD
When IC3100, IC3200 and IC3300 on the AMP board and the
complete AMP board are replaced, it is necessary to spread the
compound (THERMAL COMPOUND (G747)) (Part No. J-2501-
221-A ) between parts and heat sink.
Spread the compound referring to the fi gure below.
AMP BOARD
When IC3100, IC3200 and IC3300 on the AMP board and the
complete AMP board are replaced, it is necessary to spread the
compound (THERMAL COMPOUND (G747)) (Part No. J-2501-
221-A ) between parts and heat sink.
Spread the compound referring to the fi gure below.
– AMP Board (Component Side) –
IC3300
IC3200
IC3100
IC3100
IC3200
IC3300
CHECKING METHOD OF NETWORK OPERATION
It is necessary to check the network operation, when replacing the
MB-141 board. Check the operation of wireless and wired LAN,
according to the following method.
It is necessary to check the network operation, when replacing the
MB-141 board. Check the operation of wireless and wired LAN,
according to the following method.
1. Checking Method of Wireless LAN Operation (HBD-
E580/T58 only)
Check that access point is recognized surely.
Necessary Equipment:
Wireless access point with router function (AP)
Wireless access point with router function (AP)
Procedure:
1. Press the [HOME] button on the remote commander to enter
1. Press the [HOME] button on the remote commander to enter
the home menu.
2. Press
the
[
m]/[M]/[<]/[,] buttons on the remote command-
er to select “Network Settings”
“Internet Settings”, and press
the [
] button on the remote commander.
3. Press the [
m]/[M] buttons on the remote commander to select
“Wireless Setup (built-in)”, and press the [
] button on the
remote commander.
4. Press the [
m]/[M] buttons on the remote commander to select
“Scan”, and press the [
] button on the remote commander.
5. The system starts searching for access points, and displays a
list of up available network name (SSID).
6. Check that access point (SSID) is displayed on the searching
result.
Note: Refer to the instruction manual about details of the setting method.
2. Checking method of wired LAN operation
Check that access point is recognized surely.
Check that access point is recognized surely.
Procedure:
1. Connect the main unit to the router or the hub, etc. with the
1. Connect the main unit to the router or the hub, etc. with the
LAN cable.
2. Press the [HOME] button on the remote commander to enter
the home menu.
3. Press
the
[
m]/[M]/[<]/[,] buttons on the remote command-
er to select “Network Settings”
“Internet Settings”, and press
the [
] button on the remote commander.
4. Press the [
m]/[M] buttons on the remote commander to select
“Wired Setup”, and press the [
] button on the remote com-
mander.
5. Press
the
[
m]/[M]/[<]/[,] buttons on the remote command-
er to select “Auto”, and press the [
] button on the remote
commander.
6. Press the [
,] button on the remote commander.
7. Press the [
m]/[M] buttons on the remote commander to select
“Save & Connect”, and press the [
] button on the remote
commander.
8. When “Internet Settings is now complete.” appears, then press
the [
] button on the remote commander.
9. Press the [HOME] button on the remote commander to enter
the home menu.
10. Press the [
m]/[M]/[<]/[,] buttons on the remote command-
er to select “Network Settings”
“Internet Settings”, and press
the [
] button on the remote commander.
11. Press the [
m]/[M] buttons on the remote commander to select
“Network Connection Diagnostics”, and press the [
] button
on the remote commander.
12. Press the [
<]/[,] buttons on the remote commander to
select “Start”, and press the [
] button on the remote com-
mander.
13. Check that IP address can be acquired.
Note: Refer to the instruction manual about details of the setting method.
HBD-E380/E580/E880/E980/T58
10
HOW TO OPEN THE TRAY WHEN POWER SWITCH TURN OFF
Note 1: After the left panel (E1) is removed, this work is done.
Note 2: Please prepare the thin wire (clip etc. processed to the length of 8 cm or more).
Note 2: Please prepare the thin wire (clip etc. processed to the length of 8 cm or more).
SERVICE POSITION
3
tray
1
Remove the left panel (E1).
(Illustration of disassembly is omitted.)
2
Insert the clip etc.
tray
BD drive
Insert the clip etc.
processed to the
length of 8 cm or
more in the hole
on the side of the
chassis and push.
processed to the
length of 8 cm or
more in the hole
on the side of the
chassis and push.
8 cm or more
hole
–
Side view
–
–
Top view
–
Note: Push after it inserts it in this hole well.
FL board
POWER-SIRCS board
MB-141 board
AMP board
switching regulator
(SWR1)
(SWR1)
BD drive
(BPX-6)
(BPX-6)
HBD-E380/E580/E880/E980/T58
11
SECTION 2
DISASSEMBLY
•
This set can be disassembled in the order shown below.
2-1. DISASSEMBLY FLOW
2-3. LEFT PANEL (E1), RIGHT PANEL (E1)
(Page
(Page
12)
SET
2-5. TOP PANEL BLOCK
(Page
(Page
13)
2-2. HOW TO BEND FFC
(Page
(Page
11)
2-15. OPTICAL PICK-UP BLOCK (KEM-470AAA),
WIRE (FLAT TYPE)
(Page
19)
2-6. FL
BOARD
(Page
13)
2-13. WIRELESS LAN
CARD
CARD
(WLC1)
(E580/T58)
(Page
(Page
18)
2-14. KARAOKE BOARD
(Russian
(Russian
model)
(Page
18)
2-10. SWITCHING
REGULATOR
REGULATOR
(SWR1)
(Page
16)
2-9. AMP
BOARD
(Page
15)
2-8. BD DRIVE (BPX-6)
(Page
(Page
14)
2-7. TOP LID BLOCK
(Page
(Page
14)
2-12. FRONT PANEL BLOCK
(Page
(Page
18)
2-4. LOADING PANEL
ASSY
ASSY
(E1)
(Page
12)
2-11. MB-141 BOARD
(Page
(Page
17)
2-2. HOW TO BEND FFC
wire (flat type) (19 core), length 250 mm (Ref. No. 55)
: Mountain fold
: Valley fold
: Valley fold
wire (flat type) (26 core), length 100 mm (Ref. No. 155)
wire (flat type) (9 core), length 225 mm (Ref. No. 207)
wire (flat type) (45 core), length 238 mm (Ref. No. 208)
wire (flat type) (5 core), length 250 mm (Ref. No. 209)
MB-141 board
(CN6201)
FL board
(CN02)
15 mm
11 mm
11 mm
45º
45º
45 mm
67 mm
76 mm
45º
17 mm
65 mm
140 mm
25 mm
137 mm
75 mm
165 mm
45º
45º
45º
45º
45º
45º
45º
45º
45 mm
120 mm
35 mm
70 mm
MB-141 board
(CN5905)
AMP board
(CN3002)
The upper side
is contact side.
is contact side.
The upper side
is contact side.
is contact side.
MB-141 board
(CN2460)
The upper side
is contact side.
is contact side.
MB-141 board
(CN1301)
MB-141 board
(CN2470)
The upper side
is contact side.
is contact side.
The upper side
is contact side.
is contact side.
The upper side
is contact side.
is contact side.
The upper side
is contact side.
is contact side.
BD drive
(BPX-6)
BD drive
(BPX-6)
BD drive
(BPX-6)
The lower side
is contact side.
is contact side.
The lower side
is contact side.
is contact side.
The lower side
is contact side.
is contact side.
Ver. 1.3
HBD-E380/E580/E880/E980/T58
12
2-4. LOADING PANEL ASSY (E1)
Note: Follow the disassembly procedure in the numerical order given.
2-3. LEFT PANEL (E1), RIGHT PANEL (E1)
1
screw (BV3)
2
eight claws
4
left panel (E1)
2
eight claws
1
screw (BV3)
3
3
4
right panel (E1)
3
four claws
4
loading panel
assy
(E1)
1
Insert the clip etc.
2
tray
BD drive
Insert the clip etc.
processed to the
length of 8 cm or
more in the hole
on the side of the
chassis and push.
processed to the
length of 8 cm or
more in the hole
on the side of the
chassis and push.
8 cm or more
hole
–
Side view
–
–
Top view
–
Note: Push after it inserts it in this hole well.
Click on the first or last page to see other BDV-E380 / BDV-E580 / BDV-E880 / BDV-E980 / BDV-T58 / HBD-E380 / HBD-E580 / HBD-E880 / HBD-E980 / HBD-T58 service manuals if exist.