Sony BDV-E380 / BDV-E580 / BDV-E880 / BDV-E980 / BDV-T58 / HBD-E380 / HBD-E580 / HBD-E880 / HBD-E980 / HBD-T58 Service Manual ▷ View online
HBD-E380/E580/E880/E980/T58
17
2-11. MB-141 BOARD
A
A
5
wire (flat type) (5 core) (CN6001)
qk
wire (flat type) (19 core) (CN6201)
ql
MB-141 board
8
wire (flat type)
(7 core) (CN5909)
9
wire (flat type)
(26 core) (CN5905)
3
harness (USB)
(CN602)
harness (USB)
(E580/T58)
(EXCEPT AEP, IT, UK, EA)
B
B
J
E
F
4
harness (USB)
(CN603)
7
connector
(CN5102)
0
connector (CN5302)
qa
connector (CN5301)
6
fan connector (CN6501)
(RU)
J
qs
connector
(CN5902)
C
C
D
D
E
F
G
I
I
G
H
H
qg
screw
(BV3)
qh
two screws
(BV3)
qg
six screws
(BV3)
qf
two screws (BV3)
qf
screw (BV3)
1
four screws
(BV3)
2
drive bracket
qj
qd
three screws
(B3
u 5)
front
side
side
:LUH VHWWLQJ
(E580/T58)
:LUH VHWWLQJ
(RU)
front side
:LUH VHWWLQJ
front side
power insulated
(upper-E1)
(upper-E1)
harness (USB)
front side
:LUH VHWWLQJ
power
insulated
(lower-E1)
insulated
(lower-E1)
power
insulated
(lower-E1)
insulated
(lower-E1)
power
insulated
(lower-E1)
insulated
(lower-E1)
clamp
MB-141 board
AMP board
fan cable
:LUH VHWWLQJ
rear side
Ver. 1.3
• Abbreviation
EA
EA
: Saudi Arabia model
IT
: Italian model
RU
: Russian model
HBD-E380/E580/E880/E980/T58
18
2-12. FRONT PANEL BLOCK
2-13. WIRELESS LAN CARD (WLC1) (E580/T58)
2-14. KARAOKE BOARD (Russian model)
1
two screws
(BV3)
2
eight claws
3
front panel block
1
two screws
(BV3)
3
harness (USB)
4
wireless LAN card
(WLC1)
2
Note: When replacing the wireless LAN card (WLC1), refer to
“CHECKING METHOD OF NETWORK OPERATION”
(page 9).
(page 9).
Ver. 1.3
1
two screws
(BV3)
3
connector
(CN201)
4
KARAOKE board
2
HBD-E380/E580/E880/E980/T58
19
2-15. OPTICAL PICK-UP BLOCK (KEM-470AAA), WIRE (FLAT TYPE)
1
two screws
(BVTP
2.6)
7
two float screws (S)
qa
insulator
5
Insert the thin
wire (clip etc.).
qa
insulator
qa
insulator
qs
optical device
(KEM-470AAA)
qa
insulator
qd
non-halogene
tape
qf
wire (flat type) (5 core)
qk
wire (flat type)
(45
core)
qj
wire (flat type)
(9
core)
loading assy (D)
qh
ffc holder (rear)
2
two claws
6
8
9
qg
0
3
two claws
4
chuck holder assy (D)
– Bottom view –
1
wire (flat type) (45 core)
Fold
Under the guide.
Under the guide.
(Fold area)
(Fold area)
boss
boss
loading assy (D)
terminal face
terminal face
2
Through the hole.
4
Through the hole.
3
wire (flat type) (9 core)
5
ffc holder (rear)
7
two claws
7
three claws
6
,QVWDOODWLRQRIZLUHIODWW\SHFRUHDQGZLUHIODWW\SHFRUH
Note: This illustration sees the loading assy (D) from bottom side.
HBD-E380/E580/E880/E980/T58
20
SECTION 3
TEST MODE
COLD RESET
The cold reset clears data except BD/DVD data stored in the RAM
to initial conditions. Execute this mode when returning the unit to
the customers.
Procedure:
1. Press the [
The cold reset clears data except BD/DVD data stored in the RAM
to initial conditions. Execute this mode when returning the unit to
the customers.
Procedure:
1. Press the [
?/1
] button to turn the power on.
2. Touch the [
x
] and [VOL –] sensors simultaneously and hold
down (around 5 seconds).
3. The message “RESET” appears on fl uorescent indicator tube,
then becomes standby states.
DEMO MODE
This mode let you lock the disc tray. When this mode is activated,
the disc will not eject when the [
This mode let you lock the disc tray. When this mode is activated,
the disc will not eject when the [
Z
] sensor is touched. The mes-
sage “DEMO LOCK” will be displayed on the fluorescent indica-
tor tube.
Procedure:
1. Press the [
tor tube.
Procedure:
1. Press the [
?/1
] button to turn the power on.
2. Touch the [FUNCTION] sensor to select the “BD/DVD”.
3. Touch the [
3. Touch the [
x
] and [
Z
] sensors simultaneously and hold down
until “DEMO LOCK” or “DEMO OFF” displayed on the fluo-
rescent indicator tube (around 5 seconds).
rescent indicator tube (around 5 seconds).
Releasing method:
Touch the [
Touch the [
x
] and [
Z
] sensors simultaneously and hold down until
“DEMO OFF” displayed on the fl uorescent indicator tube (around
5 seconds).
5 seconds).
PANEL TEST
Procedure:
1. Press the [
Procedure:
1. Press the [
?/1
] button to turn the power on.
2. Press button in order of the [DISPLAY]
[0] [0] [1]
[SUBTITLE] on the remote commander (Make the interval
when each button is pressed within two seconds).
when each button is pressed within two seconds).
3. All segments in fl uorescent indicator tube are lighted up. And
half segments in fl uorescent indicator tube are lighted up, oth-
ers half segments in fl uorescent indicator tube are lighted up,
then all segments in fl uorescent indicator tube are lighted up.
This operation is repeated.
ers half segments in fl uorescent indicator tube are lighted up,
then all segments in fl uorescent indicator tube are lighted up.
This operation is repeated.
4. When all segments in fl uorescent indicator tube are lighted up
in the state of step 3, press the [VOL +] button on the remote
commander and model information is displayed on the fl uores-
cent indicator tube.
commander and model information is displayed on the fl uores-
cent indicator tube.
Each time the [VOL +] button on the remote commander is
pressed, the display changes from destination information,
STR version in this order, and returns to the model informa-
tion display.
pressed, the display changes from destination information,
STR version in this order, and returns to the model informa-
tion display.
Each time the [VOL –] button on the remote commander is
pressed, the version and date are switched.
pressed, the version and date are switched.
5. In the state of step 3, press the [FUNCTION] button on the
remote commander and “K 0” is displayed on the fluorescent
indicator tube.
indicator tube.
“K 0” value increases whenever a button or sensor on the unit
is pressed. However, once a button or sensor has been pressed,
it is no longed taken into account.
is pressed. However, once a button or sensor has been pressed,
it is no longed taken into account.
All button and sensors on the unit are pressed, “OK” and “K 7”
are alternately displayed on the fluorescent indicator tube.
are alternately displayed on the fluorescent indicator tube.
Releasing method:
To release from this mode, press the [
To release from this mode, press the [
?/1
] button.
FACTORY INITIALIZE
Return all of the unit setting to their factory defaults.
Return all of the unit setting to their factory defaults.
Note 1: Disconnect the following connections when you use this mode.
Front USB
Rear USB
LAN
HDMI IN 1
HDMI IN 2
Note 2: The operation in this mode must use a remote commander and TV
monitor.
Procedure:
1. Press the [
1. Press the [
?/1
] button to turn the power on.
2. Press the [HOME] button on the remote commander, and the
home menu is displayed.
3. Select
“Setup”
“Resetting”, and press the [ ] button on the
remote commander.
Resetting
Easy Setup
4. Select “Initialize Personal Information”, and press the [
]
button on the remote commander.
Initialize Personal Information
Erase personal data when disposing
Erase personal data when disposing
Reset to Factory Default Settings
5. Select “OK”, and press the [
] button on the remote com-
mander.
Initialize Personal Information
OK
Cancel
The information below will be deleted.
Do you want to proceed?
Playback history
Internet video utilization information
Internet content registered as Favorites
Do you want to proceed?
Playback history
Internet video utilization information
Internet content registered as Favorites
Click on the first or last page to see other BDV-E380 / BDV-E580 / BDV-E880 / BDV-E980 / BDV-T58 / HBD-E380 / HBD-E580 / HBD-E880 / HBD-E980 / HBD-T58 service manuals if exist.