Sharp VC-MH732HM (serv.man28) User Manual / Operation Manual ▷ View online
GB-33
ADVANCED OPERATION
RECORDING FROM OTHER EQUIPMENT
You can record video and audio signals from various sources, for example a camcorder, onto
a video tape using your VCR.
a video tape using your VCR.
For example, recording from a camcorder connected to LINE 2 IN/DECODER on your VCR:
1.
Load tape into the VCR.
2.
Press
INPUT SELECT
on the remote control
until the VCR display shows
L2
.
3.
If you wish to record from a source connected to
LINE 1 IN/OUT, select
LINE 1 IN/OUT, select
L1
.
4.
If you wish to record from a source connected
with audio phono leads to the sockets on the
front of the VCR (if fitted), select
with audio phono leads to the sockets on the
front of the VCR (if fitted), select
L3
.
5.
Press
REC
to start the recording.
NOTE:
•
There are many different ways of connecting external equipment to your VCR. Please
refer to your equipment operation manuals for further information.
refer to your equipment operation manuals for further information.
Optional Scart connection (not supplied)
Mono/Stereo Camcorder
RF OUT
SORTIE ANTENNE
ANTENNA IN
ENTREE ANTENNE
LINE2(II) IN
/DECODER
CANAL PLUS
/L2(II)
LINE1(I)IN
/OUT
SON/VIDEO
(L1/I)
LINE2(II) IN
/DECODER
CANAL PLUS
/L2(II)
LINE IN 3
VIDEO
L - AUDIO - R
If problems persist contact the SHARP Customer Helpline on tel: 0990-274277
GB-34
ADVANCED OPERATION
DECODER SWITCHING OPERATION
If you connect a separate decoder to the VCR connected to L2 as previously shown,
you will need to set the decoder function to
you will need to set the decoder function to
ON
in order to record the descrambled
signal and/or watch it on your TV. Now, when the VCR receives a scrambled signal
it is output via LINE 2 terminal to the decoder. The decoder then outputs the
descrambled signal back to LINE 2 terminal and the signal can be recorded. The
VCR outputs the descrambled signal to your TV through the LINE1 terminal and you
can watch the descrambled picture.
it is output via LINE 2 terminal to the decoder. The decoder then outputs the
descrambled signal back to LINE 2 terminal and the signal can be recorded. The
VCR outputs the descrambled signal to your TV through the LINE1 terminal and you
can watch the descrambled picture.
When making recordings using a separate decoder connected as shown remember
to leave the decoder function ON.
to leave the decoder function ON.
If you connect a decoder unit to the VCR, the decoder unit provides a switching
signal which will automatically allow your TV to display the descrambled signal
routed through the VCR. To use this feature make sure that the VCR is connected to
both TV and decoder unit by SCART leads. Then:
signal which will automatically allow your TV to display the descrambled signal
routed through the VCR. To use this feature make sure that the VCR is connected to
both TV and decoder unit by SCART leads. Then:
•
Press
STANDBY
to place the VCR in Stand-by mode, OR
•
Press
[TV/VCR]
on the remote control to place the VCR in ‘VCR mode’. ‘VCR’
will appear on the display.
If you switch the decoder function ON when connected to a decoder unit as shown
you will NOT be able to watch the descrambled picture in TV mode or in VCR mode.
you will NOT be able to watch the descrambled picture in TV mode or in VCR mode.
If problems persist contact the SHARP Customer Helpline on tel: 0990-274277
GB-35
ADVANCED OPERATION
REMOTE CONTROL OPERATION OF TV
In addition to operating the VCR the remote control will also operate basic functions on TVs,
including brands other than SHARP.
including brands other than SHARP.
SETTING UP THE VCR REMOTE
CONTROL TO OPERATE THE TV
CONTROL TO OPERATE THE TV
1.
Switch on the TV. Open the door on the
remote control and point the unit at the TV.
remote control and point the unit at the TV.
2.
Hold down
TV BRAND SET
on the VCR
remote control then the appropriate
button for the TV from the list shown, for 2
seconds. For example for a SHARP TV, press
button for the TV from the list shown, for 2
seconds. For example for a SHARP TV, press
TV BRAND SET
and
1
.
3.
The TV will enter standby mode to confirm
the correct code has been entered.
the correct code has been entered.
4.
To turn the TV on from standby mode hold
TV BRAND SET
and
1
for about 2
seconds.
CONTROLLING THE TV WITH THE VCR REMOTE CONTROL
•
TV OPERATE
Switches the TV to and from Standby Mode.
•
TV INPUT SELECT
Determines which input to the TV is to be displayed on the
screen.
screen.
•
TV CH
/
Changes the TV channels.
•
TV VOL
/
Increases or decreases the volume.
•
Certain models of TV do not use standard codes for their brand. In this case hold down
TV BRAND SET
, then press each of the buttons in the list until the TV enters stand-by
mode (You will need to reset when remote control batteries are replaced).
•
SHARP cannot guarantee the VCR remote control will operate your TV.
TV BRAND
BUTTON
TV BRAND
BUTTON
SHARP
1
TOSHIBA
9
PHILIPS
2
PANASONIC
0 or
THOMSON
3 or 4
HITACHI
INPUT SELECT
GRUNDIG
5
SANYO
MODE OSD
FERGUSON
6
JVC
DISPLAY
ITT NOKIA
7
MITSUBISHI
AUDIO OUT
SONY
8
+
If problems persist contact the SHARP Customer Helpline on tel: 0990-274277
GB-36
SPECIAL FEATURES ON YOUR VCR
POST CODE SECURITY
This feature should allow the Police to identify you as the owner of the VCR if it is stolen. Each
time the VCR is turned on your postcode will be displayed for 5 seconds. Your postcode
cannot be changed or removed without first entering the correct PIN - number.
time the VCR is turned on your postcode will be displayed for 5 seconds. Your postcode
cannot be changed or removed without first entering the correct PIN - number.
If you wish to use this function, follow the procedure below.
1.
Press
MENU
.
2.
Press [
/
] to select SET UP. Press
SET
to
confirm.
3.
Press [
/
] to select POST CODE. Press
SET
to confirm.
4.
Enter your desired PIN number using the
NUMBER BUTTONS
or the [
/
] key.
This must be a 4 digit number in the range
0000 - 9999.
0000 - 9999.
5.
Using the [
/
/
/
] key, enter your
Postcode. Press
SET
to confirm.
6.
Record your PIN number in the box provided
for future reference.
for future reference.
NOTE:
If you wish to change your PIN number at any time:
1.
Follow steps 1 to 3 above.
2.
Enter your current PIN number. Press
SET
to confirm
3.
Press to re-select PIN number.
4.
Enter your new PIN number. Press
SET
to confirm.
IMPORTANT:- Please keep your Operation Manual separate from your
VCR.
VCR.
•
Your Postcode can be changed at any time, but you must first enter your correct PIN
number. If the wrong PIN number is entered, an ERROR message will appear. Re-enter
the correct number.
number. If the wrong PIN number is entered, an ERROR message will appear. Re-enter
the correct number.
POS T COD E
P I N NUMB E R
POS T COD E
- - - - - - - - - - -
S E L E C T :
O P
CHANGE
M N
E N T E R : S E T E X I T : ME NU
If problems persist contact the SHARP Customer Helpline on tel: 0990-274277
Click on the first or last page to see other VC-MH732HM (serv.man28) service manuals if exist.