Sharp VC-MH721HM (serv.man11) User Manual / Operation Manual ▷ View online
17
CONNECTING TO AUDIO EQUIPMENT
The diagram below shows how to connect your VCR to audio equipment. When connected
in this way stereo sound is possible from the speakers.
The diagram below shows how to connect your VCR to audio equipment. When connected
in this way stereo sound is possible from the speakers.
RF OUT
SORTIE ANTENNE
ANTENNA IN
ENTREE ANTENNE
+
BACK OF
TELEVISION
TELEVISION
AMPLIFIER
RF OUT
AUDIO
PHONO
LEADS
AUDIO OUT
L and R
AERIAL IN
RF CONNECTION CABLE
EXISTING AERIAL
CABLE
ADVANCED OPERATION
AUDIO AND YOUR VCR
(HiFi VCR’S Only)
vc-m321/mh721hm 24/8/99 4:55 pm Page 17
18
BLUE MUTE
AUTO
OFF
➝
REPEAT
ON
OFF
▲ ▼
:SELECT
:CHANGE
SET :ENTER MENU :EXIT
ADVANCED OPERATION
PLAYBACK OF A VIDEO TAPE
Pr
CHECKING THE AMOUNT OF TAPE REMAINING
When you load a video tape into the VCR it can calculate approximately the amount of video tape
remaining in hours and minutes. This is useful in determining whether or not there is sufficient tape
left to make a recording.
When a video tape is playing, the amount of tape remaining is calculated for you automatically.
To display the amount of video tape remaining:
1.Load the video tape into the VCR.
2.Press DISPLAY on the remote control as many times as necessary until “R” appears on
When you load a video tape into the VCR it can calculate approximately the amount of video tape
remaining in hours and minutes. This is useful in determining whether or not there is sufficient tape
left to make a recording.
When a video tape is playing, the amount of tape remaining is calculated for you automatically.
To display the amount of video tape remaining:
1.Load the video tape into the VCR.
2.Press DISPLAY on the remote control as many times as necessary until “R” appears on
the VCR display. The tape will wind forward and then return to its original position. The
tape remaining will be shown on the VCR display in hours and minutes.
tape remaining will be shown on the VCR display in hours and minutes.
For example, if 1 hour 23 minutes is left on
the tape:
the tape:
1.Press MENU to display the main menu
on the screen.
2.Press [
] to select MODE.
3.Press SET.
4.Press [
4.Press [
] to select REPEAT.
5.Press [
] to select ON.
6.Press SET.
7.Press MENU to return to normal screen.
7.Press MENU to return to normal screen.
/
/
/
NOTES
●
Do not interrupt the tape remaining calculation.
●
If less than 5 minutes of tape remains the display will flash.
PLAYING BACK A VIDEO TAPE REPEATEDLY
You can set your VCR to automatically rewind at the end of playing a video tape and replay
the entire tape again. REPEAT will appear on the on-screen display when selected.
To use this feature:
You can set your VCR to automatically rewind at the end of playing a video tape and replay
the entire tape again. REPEAT will appear on the on-screen display when selected.
To use this feature:
MODE MENU SCREEN
▼
▼
vc-m321/mh721hm 24/8/99 4:55 pm Page 18
19
PLAYING BACK AN NTSC TAPE
NTSC (National Television Standards Committee) is a different TV standard to PAL and is
used in some Non-European Countries. Your VCR can playback pre-recorded NTSC tapes
onto a PAL system TV, but cannot record an NTSC signal onto a video tape.
NTSC (National Television Standards Committee) is a different TV standard to PAL and is
used in some Non-European Countries. Your VCR can playback pre-recorded NTSC tapes
onto a PAL system TV, but cannot record an NTSC signal onto a video tape.
Note that..
●
You cannot record NTSC signals or dub NTSC tapes onto other VCRs from this VCR.
●
You cannot use Slow speed, Still frame, Double Speed, Frame Advance or Tape
Remaining with a pre-recorded NTSC tape.
Remaining with a pre-recorded NTSC tape.
●
On some televisions, the picture may appear in black and white or there may be no
picture. This does not indicate a fault with your VCR.
picture. This does not indicate a fault with your VCR.
●
On some televisions, the picture may shrink vertically causing black bands to appear at
the top and bottom of your screen.
the top and bottom of your screen.
●
On some televisions, the played-back picture may roll vertically, this does not indicate a
fault with your VCR.
fault with your VCR.
ADVANCED OPERATION
PLAYBACK OF A VIDEO TAPE
vc-m321/mh721hm 24/8/99 4:55 pm Page 19
20
ADVANCED OPERATION
DIGITAL DISPLAY
NOTE:
●
The tape counter will only operate on recorded sections of tape.
TAPE COUNTER AND ZERO BACK
Tape counter measures the current position of the video tape in real time. ZERO BACK uses
the tape counter to determine a specific point on a tape you may wish to return to.
the tape counter to determine a specific point on a tape you may wish to return to.
1.Press DISPLAY until tape counter
appears, for example:
2.To identify the current position on a
video tape press CLEAR and the tape
counter will appear:
counter will appear:
When you wish to return to this position on the video tape, press ZERO BACK. The tape
will rewind/advance to this point.
will rewind/advance to this point.
Pr
Pr
Pr
Pr
TIME OF DAY
Shows current time of day, if the clock is set.
Press DISPLAY until the time of day
appears. For example, 21:20 appears:
Shows current time of day, if the clock is set.
Press DISPLAY until the time of day
appears. For example, 21:20 appears:
OPERATION MODE
Shows status of tape. Press DISPLAY until
the display appears, for example:
Shows status of tape. Press DISPLAY until
the display appears, for example:
vc-m321/mh721hm 24/8/99 4:55 pm Page 20
Click on the first or last page to see other VC-MH721HM (serv.man11) service manuals if exist.