Sharp VC-MH711HM (serv.man11) User Manual / Operation Manual ▷ View online
GB-25
ADVANCED OPERATION
DECODER SWITCHING OPERATION
If you connect a separate decoder to the VCR connected to L2 as previously shown,
you will need to set the decoder function to
you will need to set the decoder function to
ON
in order to record the descrambled
signal and/or watch it on your TV. Now, when the VCR receives a scrambled signal
it is output via LINE 2 terminal to the decoder. The decoder then outputs the
descrambled signal back to LINE 2 terminal and the signal can be recorded. The
VCR outputs the descrambled signal to your TV through the LINE1 terminal and you
can watch the descrambled picture.
it is output via LINE 2 terminal to the decoder. The decoder then outputs the
descrambled signal back to LINE 2 terminal and the signal can be recorded. The
VCR outputs the descrambled signal to your TV through the LINE1 terminal and you
can watch the descrambled picture.
When making recordings using a separate decoder connected as shown remember
to leave the decoder function ON.
to leave the decoder function ON.
If you connect a decoder unit to the VCR, the decoder unit provides a switching
signal which will automatically allow your TV to display the descrambled signal
routed through the VCR. To use this feature make sure that the VCR is connected to
both TV and decoder unit by SCART leads. Then:
signal which will automatically allow your TV to display the descrambled signal
routed through the VCR. To use this feature make sure that the VCR is connected to
both TV and decoder unit by SCART leads. Then:
•
Press
STANDBY
to place the VCR in Stand-by mode, OR
•
Press
[TV/VCR]
on the remote control to place the VCR in ‘VCR mode’. ‘VCR’
will appear on the display.
If you switch the decoder function ON when connected to a decoder unit as shown
you will NOT be able to watch the descrambled picture in TV mode or in VCR mode.
you will NOT be able to watch the descrambled picture in TV mode or in VCR mode.
If problems persist contact the SHARP Customer Helpline on tel: 0990-274277
712.book Page 25 Friday, May 14, 1999 12:08 PM
GB-26
SPECIAL FEATURES ON YOUR VCR
CHILD LOCK
You can lock your VCR with this feature. It will work even when the VCR is in standby,
preventing children from operating the VCR.
preventing children from operating the VCR.
TO ENGAGE CHILD LOCK
Press and hold
on the remote control for about 2 seconds.
flashes and then
remains lit on the VCR display confirming that CHILD LOCK
has been activated.
Regardless of what other operating buttons are touched, the VCR will continue to operate in
its present mode. If CHILD LOCK is activated during playback, once the tape reaches its end,
the VCR will automatically rewind the tape, eject it, and turn the power off.
its present mode. If CHILD LOCK is activated during playback, once the tape reaches its end,
the VCR will automatically rewind the tape, eject it, and turn the power off.
TO DISENGAGE CHILD LOCK
Press and hold
for about 2 seconds.
starts flashing and then disappears. CHILD LOCK is disengaged.
NOTES:
•
If you attempt to change modes by pressing another button while CHILD LOCK is on,
the
the
indicator will flash on the VCR display.
•
If power is interrupted for more than 60 seconds (due to power failure etc), CHILD LOCK
may disengage.
may disengage.
If problems persist contact the SHARP Customer Helpline on tel: 0990-274277
712.book Page 26 Friday, May 14, 1999 12:08 PM
GB-27
CUSTOMISED INSTALLATION
MANUALLY TUNING A CHANNEL
It should not be necessary to tune in a broadcast channel manually except in unusual
circumstances such as poor signal.
circumstances such as poor signal.
To manually tune in a channel follow the procedure below.
1.
Press
MENU
.
2.
Press [
/
] to select SET UP. Press
SET
to confirm.
3.
CHANNEL PRESET
will be
highlighted. Press
SET
.
4.
Press [
/
] to select
CHANNEL
.
5.
VC-MH712LM only
IMPORTANT NOTE:
Press
to select CH or CC. This will
determine whether off air (CH) or cable
(CC) is tuned first. Note that both off air
and cable will be tuned regardless of the
setting.
6.
Press [
/
] to start tuning in either
direction. Tuning will stop when a channel
is received. If it is not the desired channel,
press [
/
] to continue tuning.
7.
Press [
/
] to select
FINE
TUNING
. Press and hold [
/
] until
the sharpest colour picture is obtained.
9.
Press [
/
] to select
SKIP
.
The SKIP function determines whether the
channel can be selected when using the
CHANNEL
/
instead of the
NUMBER BUTTONS
.
10.
Press [
/
] to select ON or OFF for
this option.
11.
Press
SET
to confirm.
12.
Press
MENU
to leave this function.
IMPORTANT NOTE:
8.
If you connect an independent
decoder, you must press [
decoder, you must press [
/
] to
select DECODER, then select [
/
] to
turn the decoder function ON.
C HANN E L
P R E S E T
C HANN E L S O R T
C L O C K
➔
P R E S E T
1
CHANN E L
CH 2 1
F I N E T UN I NG
▲
▲
D E COD E R
ON
O F F
S K I P
ON
O F F
CABLE RECEPTION
VC-MH712LM only
Station
Signals VHF
Real
Channel
Numbers
A
B
C
D
E
F
F
G
H
J
01
02
03
04
05
06
07
08
09
02
03
04
05
06
07
08
09
If problems persist contact the SHARP Customer Helpline on tel: 0990-274277
712.book Page 27 Friday, May 14, 1999 12:08 PM
GB-28
CUSTOMISED INSTALLATION
MANUALLY SORTING CHANNELS
SORTING THE CHANNELS INTO YOUR PREFERRED ORDER
1.
Press
MENU
.
2.
Press [
/
] to select SET UP. Press
SET
to
confirm.
3.
Press [
/
] to select CHANNEL SORT. Press
SET
to confirm.
4.
Press [
/
/
/
] to highlight the
channel to be moved. Press
SET
to confirm.
5.
Press [
/
/
/
] to highlight the new
position for the channel. Press
SET
to confirm.
6.
If any more channels are to be moved,repeat
procedure from step 4.
procedure from step 4.
7.
When all the channels are in your preferred
order, press
order, press
MENU
to leave the MENU
function.
MENU SCREEN
2.
MOD E
S E T U P
MOV E
1 / 5
1 CH 2 1
7
1 3
2 CH 3 2
8
1 4
3 CH 4 3
9
1 5
4 CH 5 4
1 0
1 6
5
CH 6 5
1 1
1 7
6
1 2
1 8
5.
MOV E
1 / 5
1
CH 6 5
7
1 3
2 CH 2 1
8
1 4
3 CH 3 2
9
1 5
4 CH 4 3
1 0
1 6
5 CH 5 4
1 1
1 7
6
1 2
1 8
4.
If problems persist contact the SHARP Customer Helpline on tel: 0990-274277
712.book Page 28 Friday, May 14, 1999 12:08 PM
Click on the first or last page to see other VC-MH711HM (serv.man11) service manuals if exist.