Sharp LC-46LE811E (serv.man13) User Manual / Operation Manual ▷ View online
7
Attaching the stand unit
Before performing work, spread cushioning over the surface on which you will be laying the TV. This will prevent it from being damaged.
CAUTION
Attach the stand in the correct direction.
Be sure to follow the instructions. Incorrect installation of the stand may result in the TV falling over.
Be sure to follow the instructions. Incorrect installation of the stand may result in the TV falling over.
Confirm that there are nine screws (four long
screws and five short screws) with the stand
unit.
screws and five short screws) with the stand
unit.
Attach the supporting post for the stand unit
onto the base using the four long screws with
a screwdriver as shown.
onto the base using the four long screws with
a screwdriver as shown.
Supporting
post
Insert the stand into the openings on the
bottom of the TV (hold the stand so it will not
drop from the edge of the base area).
bottom of the TV (hold the stand so it will not
drop from the edge of the base area).
Soft cushion
1
2
3
Insert and tighten four short screws into the
four holes on the rear of the TV.
four holes on the rear of the TV.
Attaching the stand cover.
Slide the stand cover into the two catches on
the stand base.
Insert and tighten a short screw into the hole
on the centre of the stand cover.
the stand base.
Insert and tighten a short screw into the hole
on the centre of the stand cover.
NOTE
To detach the stand unit, perform the steps in reverse order.
A screwdriver is not supplied with this product.
The stand base is made of glass. Therefore, be careful not to
drop the stand base or apply pressure to it.
Do not place heavy objects on the stand base.
A screwdriver is not supplied with this product.
The stand base is made of glass. Therefore, be careful not to
drop the stand base or apply pressure to it.
Do not place heavy objects on the stand base.
4
5
1
2
•
•
•
•
•
•
•
•
•
•
Preparation
8
Using the remote control unit
Inserting the batteries
Before using the TV for the first time, insert two supplied “AAA” size alkaline batteries. When the batteries become
depleted and the remote control unit fails to operate, replace the batteries with new “AAA” size batteries.
depleted and the remote control unit fails to operate, replace the batteries with new “AAA” size batteries.
Open the battery cover.
Insert two supplied “AAA” size alkaline batteries.
Place batteries with their terminals corresponding to the (
e)
and (
f) indications in the battery compartment.
Close the battery cover.
1
2
2
•
3
CAUTION
Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.
Do not mix batteries of different types. Different types of batteries have different characteristics.
Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause chemical leakage in old
batteries.
Remove batteries as soon as they have worn out. Chemicals that leak from batteries can cause a rash. If you find any chemical leakage,
wipe thoroughly with a cloth.
The batteries supplied with this product may have a shorter life expectancy due to storage conditions.
If you will not be using the remote control unit for an extended period of time, remove the batteries from it.
When replacing the batteries, use alkaline batteries instead of zinc-carbon ones.
Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause chemical leakage in old
batteries.
Remove batteries as soon as they have worn out. Chemicals that leak from batteries can cause a rash. If you find any chemical leakage,
wipe thoroughly with a cloth.
The batteries supplied with this product may have a shorter life expectancy due to storage conditions.
If you will not be using the remote control unit for an extended period of time, remove the batteries from it.
When replacing the batteries, use alkaline batteries instead of zinc-carbon ones.
Note on disposing batteries
The batteries provided contain no harmful materials such as cadmium, lead or mercury.
Regulations concerning used batteries stipulate that batteries may no longer be thrown out with the household rubbish.
Deposit any used batteries free of charge into the designated collection containers set up at commercial businesses.
Regulations concerning used batteries stipulate that batteries may no longer be thrown out with the household rubbish.
Deposit any used batteries free of charge into the designated collection containers set up at commercial businesses.
Angle of the remote control unit
Use the remote control unit by pointing it towards the remote control sensor. Objects between the remote control unit
and sensor may prevent proper operation.
and sensor may prevent proper operation.
5 m
Remote control sensor
Cautions regarding the remote control unit
Do not expose the remote control unit to shock. In addition, do not expose the remote
control unit to liquids, and do not place in an area with high humidity.
Do not install or place the remote control unit under direct sunlight. The heat may cause
deformation of the unit.
The remote control unit may not work properly if the remote control sensor of the TV is
under direct sunlight or strong lighting. In such cases, change the angle of the lighting or
the TV, or operate the remote control unit closer to the remote control sensor.
control unit to liquids, and do not place in an area with high humidity.
Do not install or place the remote control unit under direct sunlight. The heat may cause
deformation of the unit.
The remote control unit may not work properly if the remote control sensor of the TV is
under direct sunlight or strong lighting. In such cases, change the angle of the lighting or
the TV, or operate the remote control unit closer to the remote control sensor.
•
•
•
•
•
•
•
•
•
•
•
•
Preparation
9
Initial installation overview
Follow the steps below one by one when using the TV for the first time. Some steps may not be necessary depending
on your TV installation and connection.
on your TV installation and connection.
Preparation
Connect an antenna cable to the
antenna terminal (Page 10).
antenna terminal (Page 10).
If necessary, insert a CA
card into the CI slot to watch
scrambled broadcasts (Page 10).
card into the CI slot to watch
scrambled broadcasts (Page 10).
Plug the AC cord into the AC
outlet (Page 10).
outlet (Page 10).
Product shape varies in some
countries.
Run the
initial
settings
Check that the MAIN POWER
switch on the rear of the TV is
turned on (;).
switch on the rear of the TV is
turned on (;).
The factory default for the MAIN
POWER switch is set to on (;).
POWER switch is set to on (;).
Turn on the power using
<a on the TV (Page 14).
<a on the TV (Page 14).
Run the initial auto installation
(Pages 11 and 12).
(Pages 11 and 12).
Language setting
Home/Store setting
Channel search
setting
setting
✔
✔
✔
✔
✔
Start searching
channels
•
Watch TV
Congratulations!
Now you can watch TV.
Now you can watch TV.
If necessary, adjust the antenna
to attain maximum signal
reception (Page 13).
to attain maximum signal
reception (Page 13).
Connect external
devices
Connect external devices
such as a DVD player/
recorder as instructed (Pages
20_22).
such as a DVD player/
recorder as instructed (Pages
20_22).
Connect external audio
devices such as speakers/
amplifier as instructed (Page
22).
devices such as speakers/
amplifier as instructed (Page
22).
Quick guide
10
Before turning on the power
o
q
p
2
1
n
Standard DIN45325 plug (IEC 169-2) 75
q coaxial cable
AC cord (product shape varies in some countries)
Check that the MAIN POWER switch on the rear of the TV is turned on
(;).
(;).
Cable clamp (bundle the cables with the clamp)
Place the TV close to the AC outlet,
and keep the power plug within
reach.
and keep the power plug within
reach.
Inserting the CA card into the CI module
In order to receive coded digital stations, a common interface module (CI module) and a CA card must be inserted in the
CI slot of the TV.
CI slot of the TV.
Carefully insert the CI module in
the CI slot with the contact side
forward.
The logo on the CI module must
be facing outward from the rear
of the TV.
the CI slot with the contact side
forward.
The logo on the CI module must
be facing outward from the rear
of the TV.
1
2
Checking CI module information
Go to “Menu” > “Setup” > “Option” > “CI menu”.
This menu is only available for digital stations.
The content of this menu depends on the provider of the CI module.
The content of this menu depends on the provider of the CI module.
Module
General information on CI module displays.
Menu
Adjustment parameters of each CA card displays.
Enquiry
You can input numerical values such as passwords here.
•
•
•
NOTE
It takes about 30 seconds to certify the license key when you insert a CA card into the CI+ compatible CI module for the first time. This
process may fail when there is no antenna input or you have never run “Auto installation”.
The CI+ compatible CI module sometimes upgrades its firmware. You may not receive any TV images before upgrading. You can only use
the power button during upgrading.
The CI+ compatible CI module does not allow you to output any copy protected programmes using monitor out. In this case, the copy
protect icon* is shown in the programme information when P. INFO is pressed.
Protect icon:
process may fail when there is no antenna input or you have never run “Auto installation”.
The CI+ compatible CI module sometimes upgrades its firmware. You may not receive any TV images before upgrading. You can only use
the power button during upgrading.
The CI+ compatible CI module does not allow you to output any copy protected programmes using monitor out. In this case, the copy
protect icon* is shown in the programme information when P. INFO is pressed.
Protect icon:
X
If the TV displays an update confirmation message for the CA card while receiving CI+ compatible broadcasts, follow the screen prompts.
Make sure that the CI module is properly inserted.
Make sure that the CI module is properly inserted.
•
•
•
*
•
•
•
•
Quick guide
Click on the first or last page to see other LC-46LE811E (serv.man13) service manuals if exist.