Sharp LC-46LE811E (serv.man13) User Manual / Operation Manual ▷ View online
11
Initial auto installation
When the TV is powered on for the first time after
purchase, the initial auto installation wizard appears.
Follow the menus and make the necessary settings one
after another.
purchase, the initial auto installation wizard appears.
Follow the menus and make the necessary settings one
after another.
Confirm the following before turning on
the power
the power
Is the antenna cable connected?
Is the AC cord plugged in?
Is the MAIN POWER switch turned on (;)?
Is the AC cord plugged in?
Is the MAIN POWER switch turned on (;)?
E
E
E
E
E
Press <a on the TV.
The initial auto installation wizard appears.
Setting the OSD language.
Press
a/b/c/d to select the desired language,
and then press
;.
Selecting the location of the TV.
HOME
STORE
Press
c/d to select where you will use this TV,
and then press
;.
The confirmation screen pops up only when selecting
“STORE”. Press
“STORE”. Press
c/d to select “Yes” or “No”.
HOME: “STANDARD” will be the default value for the “AV
mode” setting.
STORE: “DYNAMIC (Fixed)” will be the default value for
the “AV mode” setting. If the “AV mode” is changed, the
TV will automatically switch back to “DYNAMIC (Fixed)”
when there is no signal input from the TV or remote
control unit for 30 minutes.
STORE: A demonstration image will be displayed after
initial auto installation is completed. If you have chosen
“STORE” by mistake, go to “Setup” > “View setting” >
“Reset” > select “HOME” again.
mode” setting.
STORE: “DYNAMIC (Fixed)” will be the default value for
the “AV mode” setting. If the “AV mode” is changed, the
TV will automatically switch back to “DYNAMIC (Fixed)”
when there is no signal input from the TV or remote
control unit for 30 minutes.
STORE: A demonstration image will be displayed after
initial auto installation is completed. If you have chosen
“STORE” by mistake, go to “Setup” > “View setting” >
“Reset” > select “HOME” again.
1
•
2
3
•
•
•
•
Starting channel search.
Digital search
Analogue search
Press
c/d to select “Digital search” or “Analogue
search”, and then press
;.
To watch both analogue broadcasts and digital
broadcasts, you should perform the auto installation
setting for each format (Page 30).
If you want to search for more broadcasts, execute
“Additional search” from the “Programme setup” menu
(Pages 30_32).
broadcasts, you should perform the auto installation
setting for each format (Page 30).
If you want to search for more broadcasts, execute
“Additional search” from the “Programme setup” menu
(Pages 30_32).
NOTE
If you turn off the power on the TV while performing a channel
search, the initial auto installation wizard will not appear. The
auto installation function allows you to execute the installation
again from “Setup” > “View setting” (Page 30).
The initial auto installation wizard will abort if you leave the TV
unattended for 30 minutes before searching for channels.
After initial auto installation is completed, the default PIN is
automatically set to “1234”. To change the PIN setting, refer to
Password/Lock settings
search, the initial auto installation wizard will not appear. The
auto installation function allows you to execute the installation
again from “Setup” > “View setting” (Page 30).
The initial auto installation wizard will abort if you leave the TV
unattended for 30 minutes before searching for channels.
After initial auto installation is completed, the default PIN is
automatically set to “1234”. To change the PIN setting, refer to
Password/Lock settings
(Page 33). To clear the PIN setting
(PIN input will no longer be needed), refer to CLEARING THE
PIN
PIN
(Page 50).
Digital broadcast setting
Press
c/d to select “Terrestrial” or “Cable”,
and then press
;.
Terrestrial
Cable
Searching for terrestrial broadcasts
The TV searches for, sorts and stores all the
receivable TV stations according to their
settings and the connected antenna.
receivable TV stations according to their
settings and the connected antenna.
To abort the initial auto installation in progress, press 6.
NOTE
When regional services overlapps causing conflicts where the
services compete for the same number, the receiver displays
a menu to allow the viewer selecting a target region for the
conflict resolution.
services compete for the same number, the receiver displays
a menu to allow the viewer selecting a target region for the
conflict resolution.
4
•
•
•
•
•
E
•
•
Quick guide
12
Quick guide
Searching for cable broadcasts
To change each item to the appropriate
settings:
settings:
Press
a/b to select the menu, and then
press
;.
Scrambled stations
[Yes]
Search method
[Channel]
Start frequency
Network ID
[None]
Symbol rate 1
Symbol rate 2
QAM modulation 1
QAM modulation 2
Reset
Search start
Press
a/b/c/d or 0_9 to select or input
the appropriate item/value, and then press
;.
Press
;.
Press
a/b to select “Search start”, and then
press
;.
Press
c/d to select “Yes” to start searching
cable broadcasts, and then press
;.
The TV searches for, sorts and stores all
the receivable TV stations according to their
settings and the connected antenna.
the receivable TV stations according to their
settings and the connected antenna.
To abort the initial auto installation in progress, press 6.
E
1
2
3
4
5
•
Menu
Description
Selectable items
Scrambled
stations
stations
Specifies if you
need to add pay-TV
services.
need to add pay-TV
services.
Yes, No
Search
method
method
Specifies how you
search channels.
search channels.
Channel: Extracts all
of information from a
channel (quick, but
needs corresponding
TV stations).
Frequency: Checks
every frequency in
range (slow).
Quick*
of information from a
channel (quick, but
needs corresponding
TV stations).
Frequency: Checks
every frequency in
range (slow).
Quick*
2
: All services
are searched by
one frequency. This
menu works only
when your cable
provider provides
the frequency and
the network ID (e.g.,
Homing channel).
one frequency. This
menu works only
when your cable
provider provides
the frequency and
the network ID (e.g.,
Homing channel).
Start
frequency
frequency
From 474.0_858.0
MHz
MHz
Network ID
Specifies the network.
Set this to register
only the specified
network ID without
registering any special
services.
Set this to register
only the specified
network ID without
registering any special
services.
None, 0_65535
Symbol rate
1*
1*
1
The symbol rates
are specified by the
cable provider. Input
the value received for
CATV.
are specified by the
cable provider. Input
the value received for
CATV.
1000_9000
Symbol rate
2*
2*
1
The symbol rates
are specified by the
cable provider. Input
the value received for
CATV.
are specified by the
cable provider. Input
the value received for
CATV.
1000_9000
QAM
modulation 1
modulation 1
16, 32, 64, 128, 256
QAM
modulation 2
modulation 2
None, 16, 32, 64,
128, 256
128, 256
Set up “Symbol rate 2” if the cable provider uses several
symbol rates.
When “Quick” is selected, “Scrambled stations” is automatically
set to “No”.
When “Quick” is selected, “None” for the “Network ID” menu
cannot be selected.
symbol rates.
When “Quick” is selected, “Scrambled stations” is automatically
set to “No”.
When “Quick” is selected, “None” for the “Network ID” menu
cannot be selected.
Analogue broadcast setting
The TV searches for, sorts and stores all the
receivable TV stations according to their
settings and the connected antenna.
receivable TV stations according to their
settings and the connected antenna.
To abort the initial auto installation in progress, press 6.
I
J
J
•
13
Quick guide
Checking signal strength and
channel strength (DVB-T/T2/C)
channel strength (DVB-T/T2/C)
If you install a DVB-T/T2/C antenna for the first time
or relocate it, you should adjust the alignment of the
antenna to receive a good reception while checking the
antenna setup screen.
or relocate it, you should adjust the alignment of the
antenna to receive a good reception while checking the
antenna setup screen.
Go to “Menu” > “Setup” > “View setting”
> “Channel settings” > “Antenna setup-
DIGITAL”.
> “Channel settings” > “Antenna setup-
DIGITAL”.
Checking signal strength
Press
a/b to select “Signal strength”, and
then press
;.
Supply voltage
CH No.
Current
Max.
Signal strength
Signal strength
Channel strength
Current
Max.
Quality
Checking channel strength
Press
a/b to select “Channel strength”, and
then press
;.
You can input a specified frequency band using the 0_9
numeric buttons.
numeric buttons.
1
E
2
E
3
•
Channel strength of DVB-T/T2
Supply voltage
CH No.
Current
Max.
Signal strength
MHz
Signal strength
Frequency
Channel strength
Current
Max.
Quality
Channel strength of DVB-C
Supply voltage
Current
Max.
Signal strength
MHz
Signal strength
Frequency
Symbol rate
QAM modulation
Symbol rate
QAM modulation
Channel strength
Current
Max.
Quality
Position and align the antenna so that
the maximum possible values for “Signal
strength” and “Quality” are obtained.
the maximum possible values for “Signal
strength” and “Quality” are obtained.
NOTE
The values of “Signal strength” and “Quality” indicate when to
check the appropriate alignment of the antenna.
check the appropriate alignment of the antenna.
4
•
Supplying power to the antenna
You must supply power to the antenna in order to receive digitally/terrestrially broadcast stations after connecting
the antenna cable to the antenna terminal on the rear of the TV.
the antenna cable to the antenna terminal on the rear of the TV.
Press @ and the “Menu” screen displays.
Press
Press
c/d to select “Setup”, and then press ;.
Press
c/d to select “View setting”, and then press ;.
Press
a/b to select “Channel settings”, and then press ;.
Press
a/b to select “Antenna setup-DIGITAL”, and then press ;.
Press
a/b to select “Supply voltage”, and then press ;.
Press
c/d to select “On”, and then press ;.
1
2
3
4
5
6
7
2
3
4
5
6
7
14
Daily operation
Switching on/off
Turning on/off the power
Turn on (;) the MAIN POWER switch on the
rear of the TV (Page 4).
rear of the TV (Page 4).
To turn on the TV, press <a on the TV
or >a on the remote control unit.
or >a on the remote control unit.
To turn off the TV, press <a on the TV
or >a on the remote control unit.
or >a on the remote control unit.
Turn off (a) the MAIN POWER switch on the
rear of the TV (Page 4).
rear of the TV (Page 4).
When turning off the power using the MAIN POWER
switch on the rear of the TV, EPG data will be lost.
switch on the rear of the TV, EPG data will be lost.
Standby mode
To standby mode
If the MAIN POWER switch on the rear of the TV is
turn on (;), you can switch it to standby by pressing
<a on the TV or >a on the remote control unit.
turn on (;), you can switch it to standby by pressing
<a on the TV or >a on the remote control unit.
Switching on from standby
From standby, press <a on the TV or >a on
the remote control unit.
the remote control unit.
NOTE
If you are not going to use this TV for a long period of time, be
sure to remove the AC cord from the AC outlet or turn off (a)
the MAIN POWER switch on the rear of the TV (Page 4).
A small amount of electric power is still consumed even when
the MAIN POWER switch is turned off (a) (Page 4).
sure to remove the AC cord from the AC outlet or turn off (a)
the MAIN POWER switch on the rear of the TV (Page 4).
A small amount of electric power is still consumed even when
the MAIN POWER switch is turned off (a) (Page 4).
1
2
3
4
•
E
E
•
•
Switching between digital and
analogue broadcasts
analogue broadcasts
Watching digital
broadcasts
broadcasts
Watching analogue
broadcasts
broadcasts
Changing channels
With :r/s
With 0_9
Watching TV
Click on the first or last page to see other LC-46LE811E (serv.man13) service manuals if exist.