Sharp LC-45GD1E (serv.man43) User Manual / Operation Manual ▷ View online
7
System cable
AVC System (rear view)
AC cord
Display (rear view)
AC cord
System cable
(GREY)**
Connect the plug firmly
until the hooks on both
sides click.
Connect the plug firmly
until the hooks on both
sides click.
(WHITE)*
Connect the plug into the
terminal and secure it by
tightening the thumb screws.
Connect the plug into the
terminal and secure it by
tightening the thumb screws.
Setting the System
After putting the Display and the AVC System in place, connect the system cables and AC cords. Use the
cable clamps for bundling the cables.
Preparation
Press down the four
upper hooks to remove
the cover toward you.
upper hooks to remove
the cover toward you.
Connecting the system cable and the AC cord to the Display
1
2
3
Removing the terminal cover
Connecting the system cable and the AC cord to the AVC System
CAUTION
• TO PREVENT RISK OF ELECTRIC SHOCK, DO NOT TOUCH UN-INSULATED PARTS OF ANY CABLES WITH THE
AC CORD CONNECTED.
• To comply with the requirements of the CE regulation rules, make sure to attach the terminal cover to the rear of the
display with all the system cables connected before you use this product.
NOTE
* When you unplug the WHITE system cable, make sure you unscrew the screws thoroughly before unplugging the cable.
** When you unplug the GREY system cable, press the hooks on both sides of the cable inward as you unplug the cable gently.
** When you unplug the GREY system cable, press the hooks on both sides of the cable inward as you unplug the cable gently.
Press the two hooks
toward the centre of the
Display and remove the
cover toward you.
toward the centre of the
Display and remove the
cover toward you.
(GREY)
(WHITE)
(BLACK)
(BLACK)
LC-45GD1E(E)-a
04.9.27, 9:57 AM
7
8
Preparation
4
5
Attaching the clamp and bundling the cables with the clamp
Closing the terminal cover
Cable clamp
Insert the cable clamp in the hole on the Display as shown.
Cables come
out from the
small opening.
out from the
small opening.
Fasten the speaker cable
with the holder.
with the holder.
LC-45GD1E(E)-a
04.9.27, 9:58 AM
8
9
Preparation
Setting the AVC System with the stand
How to install the AVC System vertically using the stand unit.
• Use the supplied stand unit for installing the AVC System vertically in an upright position.
• Use the supplied stand unit for installing the AVC System vertically in an upright position.
NOTE
• When mounting the AVC System vertically, always use the supplied stand. Be careful not to block vent holes when
standing up directly on the floor or a flat surface as this can result in equipment failure.
1
Stick each spacer to the
stand as shown.
stand as shown.
Peel each spacer away from the paper
and attach to the four bulging areas
on the stand.
and attach to the four bulging areas
on the stand.
2
Attach each cushion to
the stand as shown.
the stand as shown.
3
Fit the stand to the AVC
System.
System.
Peel each cushion
away from the
paper and attach
to the four areas
at the bottom.
away from the
paper and attach
to the four areas
at the bottom.
Insert the stand into the AVC
System, making sure that the
thick and thin bulges of the
stand align with the big and
small holes on the AVC
System.
System, making sure that the
thick and thin bulges of the
stand align with the big and
small holes on the AVC
System.
Stand
spacer
spacer
Bulge
Stand cushion
Bulge
Hole
4
Attach the stand using the
stand screws as shown.
stand screws as shown.
Stand screw
The AVC System installed
vertically with the stand.
vertically with the stand.
Attaching point
Attaching point
Bulge
LC-45GD1E(E)-a
04.9.27, 9:58 AM
9
10
Removing speakers
Preparation
NOTE
• To attach the speakers, perform the steps in reverse order.
• Perform the same steps for the left section of the speaker.
• Perform the same steps for the left section of the speaker.
CAUTION
• Do not remove the stand and speaker from the Display unless using an optional bracket to mount it.
• Before performing work spread cushioning over the base area to lay the Display on. This will prevent it from
• Before performing work spread cushioning over the base area to lay the Display on. This will prevent it from
being damaged.
1
2
3
4
Unfasten the screw used to secure the speaker
bracket.
bracket.
Unfasten the screws.
Take off the speaker terminal cover.
Disconnect the cable from the speaker.
LC-45GD1E(E)-a
04.9.27, 9:58 AM
10
Click on the first or last page to see other LC-45GD1E (serv.man43) service manuals if exist.