DOWNLOAD Sharp LC-42DH77EC (serv.man5) Service Manual ↓ Size: 712.23 KB | Pages: 18 in PDF or view online for FREE

LC-32/42/46DH77E/RU/S

3 – 5

15/16

[FR REGI]

1

READ/WRITE

READ

Read/Write

2

SLAVE/ADDRESS

SLAVE0

Slave address

3

RESISTER ADDRESS

0x 0

Register address

0x 0

4

WRITE DATA

0x 0

Writing data

0x 0

5

READ DATA

0x 0

Reading data

0x 0

16/16

[ETC]

1

EEP SAVE

OFF

Writing setting values to EEPROM.

2

EEP RECOVER

OFF

Reading setting values from EEPROM.

3

MONITOR ERROR CAUSE RESET

OFF

Reset of monitor error cause

4

STANDBY CAUSE RESET

OFF

Reset stand by cause.

5

MODEL NAME

DH77

Model name setting

6

PANEL SIZE

32/42/46

Panel size setting. (32/37/42/46/52/65)

7

PRODUCT EEP ADR

0x 0

Don't touch when serving (for producer of factory)

8

PRODUCT EEP DATA

0x 0

Don't touch when serving (for producer of factory)

LC-32/42/46DH77E/RU/S

3 – 6

1. NORMAL STANDBY CAUSE (Page 1/16)

Display of a cause (code) of the last standby.

The cause of the last standby is recorded in EEPROM whenever possible.

Checking this code will be useful in finding a problem when you repair the troubled set.

2. EEP SAVE (Page 16/16)

Storage of EEP adjustment value

3. EEP RECOVER (Page 16/16)

Retrieval of EEP adjustment value from storage area.

1. Function

This LCD colour TV set incorporates a lamp error detection feature that automatically turns off the power for safety under abnormal lamp or lamp
circuit conditions. If by any chance anything is wrong with the lamp or lamp circuit or if the lamp error detection feature is activated for some rea-
son, the following will result.

1) The power is interrupted in about 6 seconds after it is turned on.

(The power LED on the front of the TV set turns red from green and keeps blinking in red: ON for 300ms and OFF for 1500ms.).

2) If the above phenomenon 1) occurs 5 times consecutively, it becomes impossible to turn on the power. (The power LED remained red).

2. Measures

1) Checking with lamp error detection OFF

Enter the adjustment process mode, referring to 2. Entering and exiting the adjustment process mode.

If there is a problem with the lamp or lamp circuit, the lamp will go out. (The power LED is green.)

Then, you can check the operation to see if the lamp and lamp circuit are in trouble.

2) Resetting the lamp error count

After the lamp and lamp circuit are found out of trouble, reset the lamp error count. If a lamp error is detected five consecutive times, the power
cannot be turned on. Using the cursor (

/

) key, move to the cursor to [LAMP ERROR RESET], Line 8 on adjustment process mode ser-

vice page 2/16.

With the cursor (</>) keys, select the [LAMP ERROR RESET] value. Finally press the cursor (OK) eys to reset the value to “0”.

INDUSTRY INIT

Enter

INDUSTRY INIT (-Hotel)

OFF

HOTEL MODE

OFF

Center Acutime

5H0M

RESET

OFF

Backlight Acutime
RESET

OFF

LAMP ERROR RESET

OFF

Resetting to "0"

ADJ PARAM SET

Enter

VIC XPOS

0

VIC YPOS

0

VIC SIGNAL TYPE

MAIN

VIC READ

OFF

LC-32/42/46DH77E/RU/S

3 – 7

1. Starting the Public Mode

• There are two following ways to display the PUBLIC Mode setting screen.

1) On the process adjustment mode screen (2/16), set the “HOTEL MODE” Flag to ON.

Turn off the power, and turn it on again, pressing the 

 and 

 keys of the main unit at the same time.

2) Enter the Pass Word, and start the unit.

a) Turn on the power, pressing the 

 and 

 keys of the main unit at the same time.

b) Display the Pass Word input screen.

Operation procedure

• The initial input position is the digit at the left end.

• For the numeric keys 

 to 

 of R/C, key input is accepted. Input of the other keys is prohibited.

• Change “–” to “*” by inputting the numeric key at the input position, and shift the input position rightward one digit.

• When three digits are completely input, the Pass Word is judged.

c) Check the Pass Word by inputting three digits.

If the Pass Word is 

, it shifts to the PUBLIC Mode setting screen.

In another case, the screen is erased, and it operates in the ordinary mode.

2. Exiting the Public Mode screen

• There are two following ways to exit the Public Mode setting screen.

1) Turn off the power.

2) Select “Execution” in the PUBLIC_Mode to execute it.

Activate the restart under the set content. Here, the START input SOURCE setting is excluded since this item is referred to only when the
power is turned on.

3. Set value of the Public Mode

• When the shipment setting is done, a set each value in Public Mode is initialized.

(PUBLIC MODE in the process mode Setting of a flag is also initialized)

• Separately, the shipment beginnings when all except for each set value in Public Mode is initialized are provided for a process mode.

(INDUSTRY INIT (-HOTEL))

• Only when turning on the HOTELE MODE item, each setting is effective.

• After it decides it with EXECUTE, it AC OFF/ON it to reflect a set value.

CHANNEL UP

Volume UP

INPUT

Volume UP

0

9

0

2

7

LC-32/42/46DH77E/RU/S

3 – 8

4. Basic operation in the Public Mode

5. Operation after “RESET”

Select “RESET” in the PUBLIC Mode, and it operates as follows when it is executed (refer to the basic operation).

• The set contents in the PUBLIC mode are initialized.

• It does not exit the PUBLIC mode.

• If “EXCUTE” is not executed, the content that does RESET is not reflected.

Volume (

/

) or Cursor (

</>)

Change or execution of the set value.

Channel (

/

) or Cursor (

/

)

Movement to the selected item.

Decision (ok)

Execution (Used by the items “Execution” and “RESET”.)

PUBLIC Mode R/C

Ordinary operation mode: It enters the PUBLIC Mode.

PUBLIC MODE Flag is set to “ON”.

PUBLIC Mode: It exits the PUBLIC Mode.

PUBLIC MODE Flag does not change.
Any set item in PUBLIC Mode is not initialized.