Sharp LC-40CT2E (serv.man2) Service Manual ▷ View online
15.2.4
Absolute Maximum Ratings
15.2.5
Pinning
15.3 NUP4004M5
15.3.1
General Description
This 5-Pin bi-directional transient suppressor array is designed for applications requiring
transient overvoltage protection capability. It is intended for use in transient voltage and
ESD sensitive equipment such as computers, printers, cell phones, medical equipment,
and other applications. Its integrated design provides bi-directional protection for four
separate lines using a single TSOP-5 package. This device is ideal for situations where
board space is a premium.
transient overvoltage protection capability. It is intended for use in transient voltage and
ESD sensitive equipment such as computers, printers, cell phones, medical equipment,
and other applications. Its integrated design provides bi-directional protection for four
separate lines using a single TSOP-5 package. This device is ideal for situations where
board space is a premium.
15.3.2
Features
Bi-directional Protection for Four Lines in a Single TSOP-5 Package
Low Leakage Current
Low Capacitance
Provides ESD Protection for JEDEC Standards JESD22
Machine Model = Class C
Human Body Model = Class 3B
Provides ESD Protection for IEC 61000-4-2, 15 kV (Air), 8 kV (Contact)
This is a Pb-Free Device
15.3.3
Absolute Maximum Ratings
15.3.4
Pinning
15.4 FDN336P
15.4.1
General Description
The ST24LC21 is a 1K bit electrically erasable programmable memory (EEPROM),
organized by 8 bits.This device can operate in two modes: Transmit Only mode and I2C
bidirectional mode. When powered, the device is in Transmit Only mode with EEPROM
data clocked out from the rising edge of the signal applied on VCLK. The device will
switch to the I2C bidirectional mode upon the falling edge of the signal applied on SCL
pin. The ST24LC21 cannot switch from the I2C bidirectional mode to the Transmit Only
mode (except when the power supply is removed). The device operates with a power
supply value as low as 2.5V. Both Plastic Dual-in-Line and Plastic Small Outline
packages are available.
organized by 8 bits.This device can operate in two modes: Transmit Only mode and I2C
bidirectional mode. When powered, the device is in Transmit Only mode with EEPROM
data clocked out from the rising edge of the signal applied on VCLK. The device will
switch to the I2C bidirectional mode upon the falling edge of the signal applied on SCL
pin. The ST24LC21 cannot switch from the I2C bidirectional mode to the Transmit Only
mode (except when the power supply is removed). The device operates with a power
supply value as low as 2.5V. Both Plastic Dual-in-Line and Plastic Small Outline
packages are available.
15.4.2
Features
1 MILLION ERASE/WRITE CYCLES
40 YEARS DATA RETENTION
2.5V to 5.5V SINGLE SUPPLY VOLTAGE
400k Hz COMPATIBILITY OVER the FULL RANGE of SUPPLY VOLTAGE
TWO WIRE SERIAL INTERFACE I2C BUS COMPATIBLE
PAGE WRITE (up to 8 BYTES)
BYTE, RANDOM and SEQUENTIAL READ MODES
SELF TIMED PROGRAMMING CYCLE
AUTOMATIC ADDRESS INCREMENTING
ENHANCED ESD/LATCH UP PERFORMANCES
15.4.3
Absolute Maximum Ratings
15.4.4
Pinning
15.5 TL062 -
15.5.1
General Description
Low-power JFET-input operational amplifier
15.5.2
Features
Very Low Power Consumption
Typical Supply Current . . . 200 µA (Per Amplifier)
Wide Common-Mode and Differential Voltage Ranges
Low Input Bias and Offset Currents
Common-Mode Input Voltage Range Includes VCC+
Output Short-Circuit Protection
High Input Impedance . . . JFET-Input Stage
Internal Frequency Compensation
Latch-Up-Free Operation
High Slew Rate . . . 3.5 V/µs Typ
Click on the first or last page to see other LC-40CT2E (serv.man2) service manuals if exist.