Sharp LC-39LE751EK (serv.man5) User Manual / Operation Manual ▷ View online
Reception of a single satellite via a connected LNC
(LNB).
(LNB).
1
Select satellite.
Press
J
to continue.
2
Select Dual Band (low/high) or Single Band.
Here you specify if you use a Dual Band (Universal)
LBN or Single LBN.
LBN or Single LBN.
Press
J
to continue.
3
Specify here the oscillator frequency for your LNB.
Normally you do not need to change the values
for high and low band, unless the LNB of your
satellite system uses a different oscillator frequency
(important for the frequency display).
If you use the setting Single Band in step Dual/
Single Band,
for high and low band, unless the LNB of your
satellite system uses a different oscillator frequency
(important for the frequency display).
If you use the setting Single Band in step Dual/
Single Band,
you only have to define the LNB
frequency for the Low Band.
4
Press
J
to continue.
See Setting options for all DVB-S reception on
page 13
page 13
to continue.
Quick guide
1
Select
Satellite1/Satellite2
2
Select satellite name from list and press
OK.
Press
J
to continue.
3
Specify here the oscillator frequency for your LNB.
Normally you do not need to change the values
for high and low band, unless the LNB of your
satellite system uses a different oscillator frequency
(important for the frequency display).
for high and low band, unless the LNB of your
satellite system uses a different oscillator frequency
(important for the frequency display).
4
Press OK to select frequency and press
J
to
continue.
See Setting options for all DVB-S reception on
page 13
page 13
to continue.
Select DiSEqC multiswitch and adpat settings for this
selection.
selection.
11
Setting options for Single satellite
Setting options for Max. 4 satellites on DiSEqC
multiswitch
multiswitch
Setting options for 2 satellites on 22kHz
switchbox / 2 satellites on Toneburst switch
switchbox / 2 satellites on Toneburst switch
1
Select which DiSEqC single cable system you are
using and press OK.
2
Select satellite name from list and press OK. Press
J
to continue.
3
Specify here the oscillator frequency for your LNB
and press OK. Press
J
to continue.
Normally you do not need to change the values
for high and low band, unless the LNB of your
satellite system uses a different oscillator frequency
(important for the frequency display).
for high and low band, unless the LNB of your
satellite system uses a different oscillator frequency
(important for the frequency display).
4
Select and adjust settings for DiSEqC single cable
communal installation.
Select the desired transmission channel and the
corresponding transmission frequency.
corresponding transmission frequency.
PIN protection
If your system is designed for it, it is possible to
protect your used transmission data from use by
other subscribers with a PIN.
If your system is designed for it, it is possible to
protect your used transmission data from use by
other subscribers with a PIN.
Define/change PIN
Here you can determine and change the PIN for
PIN protection
Here you can determine and change the PIN for
PIN protection
. Only possible when yes has been
selected for PIN protection.
Continue with Setting options for all types of
reception
reception
on page 13.
Quick guide
Press OK to adopt settings and press
J
to continue.
1
Select
Satellite1
to Satellite4.
2
Select satellite name from list and press OK.
Press
J
to continue.
3
Specify here the oscillator frequency for your LNB.
Normally you do not need to change the values
for high and low band, unless the LNB of your
satellite system uses a different oscillator frequency
(important for the frequency display).
for high and low band, unless the LNB of your
satellite system uses a different oscillator frequency
(important for the frequency display).
See Setting options for all DVB-S reception on
page 13
page 13
to continue.
●
Repeat rate
The refresh rate determines how often a DiSEqC
command is output. A refresh is only necessary with
cascaded system.
command is output. A refresh is only necessary with
cascaded system.
●
Control voltage
The control voltage controls the switch of the
polarisation level (horizontal/vertical) in non-DiSEqC
capable components (e.g., control of single LNBs
via DiSEqC multiswitch).
polarisation level (horizontal/vertical) in non-DiSEqC
capable components (e.g., control of single LNBs
via DiSEqC multiswitch).
●
22kHz signal
The 22kHz signal controls the switching between
high and low band in the Band setting. The Position
setting controls the selection of the satellites in non-
DiSEqC capable components.
high and low band in the Band setting. The Position
setting controls the selection of the satellites in non-
DiSEqC capable components.
●
Toneburst
The Toneburst controls the selection of the satellites
in non-DiSEqC but Toneburst capable components
with the Position and Option settings.
in non-DiSEqC but Toneburst capable components
with the Position and Option settings.
12
Setting options for DiSEqC one cable
communal system
communal system
Quick guide
1
Select
satellite.
Press
J
to continue.
2
Specify here the oscillator frequency for your LNB.
If your set is connected to a single-cable system
without external voltage supply, you can connect
the antenna supply (13V or 18V / max. 450mA)
with 13V or 18V.
the antenna supply (13V or 18V / max. 450mA)
with 13V or 18V.
Continue with Setting options for DVB-S reception
below.
below.
●
Network selection
If several networks are available via DVB-S, you
can decide which network you want to receive your
channels from.
can decide which network you want to receive your
channels from.
●
Settings
If several satellites are received, the following settings
must be made for every satellite. The type of settings
available may differ depending on the selected satellite
or network.
must be made for every satellite. The type of settings
available may differ depending on the selected satellite
or network.
Setting options for DVB-S reception
●
Scrambled stations
Select yes to save all scrambled stations.
• These stations can only be received in connection
• These stations can only be received in connection
with a CI module and the appropriate CA Card.
• If a CI module with a CA Card is already inserted
for the station search, all the stations which this
module can descramble are also saved when no
is selected.
module can descramble are also saved when no
is selected.
●
Search method
If you select Frequency Search here, a search is
performed for all receivable stations. With Network
Search
performed for all receivable stations. With Network
Search
, from all receivable networks all the stations are
searched which are supplied by these networks.
●
Symbol rate
The symbol rate is specified by the satellite provider and
normally does not need to be changed.
normally does not need to be changed.
●
Accept Logical Channel Number
This setting allows you to decide whether you want to
accept the Logical Channel Number (LCN).
Press
accept the Logical Channel Number (LCN).
Press
J
to continue.
Continue with Setting options for all types of
reception
reception
below.
●
Age related lock
Allows you to restrict programmes depending on the age
classification.
classification.
The information about age classification is provided by
the broadcasting station.
The stations locked can only be watched after entering
the access code (see page 24).
the broadcasting station.
The stations locked can only be watched after entering
the access code (see page 24).
●
Time and date
Enter the correct values with the numeric buttons here.
●
●
Network configuration
Here you can now specify if you wish to configure a
network "Configure now" (see page 47) or you wish
to configure it later "Do not configure or configure
later"
network "Configure now" (see page 47) or you wish
to configure it later "Do not configure or configure
later"
.
13
Setting options for Other communal installation
Setting options for all types of reception
Quick guide
If you install a DVB-T/T2/S/S2 antenna for the first time
or relocate it, you should adjust the alignment of the
antenna to receive a good reception while checking the
antenna setup screen.
or relocate it, you should adjust the alignment of the
antenna to receive a good reception while checking the
antenna setup screen.
In normal TV mode, without other displays, a DVB-T
station is received and selected.
station is received and selected.
1
Select
Setup.
2
Select
Stations.
3
Select Manual Scan TV.
Position and align the antenna in such a manner that
maximum values for C/N and Level are obtained.
The value for BER should be as low as possible.
maximum values for C/N and Level are obtained.
The value for BER should be as low as possible.
4
Select Search and press OK to start search.
Positioning / aligning DVB-T
antenna
14
Click on the first or last page to see other LC-39LE751EK (serv.man5) service manuals if exist.