Sharp LC-37AD1E (serv.man9) Service Manual ▷ View online
46
LC-37AD1E
YES
YES
NO
NO
NO
YES
No picture comes out.
Is the input to pins (139), (124) and (133)
of IC10004 normal?
of IC10004 normal?
Check CN10007 and the
peripheral circuitry.
peripheral circuitry.
Check IC10004 and the
peripheral circuitry.
peripheral circuitry.
Is the digital output section of IC10004
normal?
normal?
Check IC10426 and the
peripheral circuitry.
peripheral circuitry.
Check IC10004 and the
peripheral circuitry.
peripheral circuitry.
Is the digital output section of IC10426
normal?
normal?
Check IC10025 and the
peripheral circuitry.
peripheral circuitry.
Is the digital output from IC10025 normal?
Check IC10025 and the
peripheral circuitry.
peripheral circuitry.
Is the digital output from IC10025 normal?
YES
YES
YES
Is the input to pins (141), (126) and (136)
of IC10004 normal?
of IC10004 normal?
Is the digital output section of IC10004
normal?
normal?
NO
NO
NO
NO
NO
NO
YES
YES
YES
Is the input to pins (3), (2) and (1) of
IC10426 normal?
IC10426 normal?
Check CN10007 and the
peripheral circuitry.
peripheral circuitry.
Check the display side.
(AVC System)
(PC I/F Unit)
MAIN in one-screen mode or two-screen
mode
mode
SUB in two-screen mode
Is the signal applied to pins (21), (22),
(24), (25), (27), (28), (30) and (31) of
IC10413?
(24), (25), (27), (28), (30) and (31) of
IC10413?
Check the parts in the PC I/F unit.
In the case of TV, video and component system
In the case of PC system
Note: The Ref.
No. of the PC I/F unit is REF.1XXXX.
No. of the PC I/F unit is REF.1XXXX.
Check CN10008 and the
peripheral circuitry.
peripheral circuitry.
47
LC-37AD1E
TROUBLE SHOOTING TABLE
(Display)
YES
NO
NO
YES
NO
NO
YES
YES
YES
YES
NO
NO
YES
NO
No sound or picture comes out.
Does the power LED
light up in green.
light up in green.
Is the Backlight off?
Perform checking
around IC2204.
around IC2204.
Is "LOSS OF SYNC"
displayed?
displayed?
To "No picture comes
out"
out"
Perform checking
around IC2208.
around IC2208.
Is the power LED
blinking in red?
blinking in red?
Is the AC cable
normal?
normal?
NO
Replace the
AC cable.
AC cable.
Blinking once?
Blinking twice?
Blinking five times?
Blinking seven times?
To "The backlight does not go on"
Check the power unit.
Check the temperature of the set.
Check the 1-bit amplifier unit.
250ms
1sec
LTD operation (1 cycle)
H: ON
L: OFF
H: ON
H: ON
L: OFF
H: ON
L: OFF
H: ON
H: ON
L: OFF
H: ON
H: ON
L: OFF
H: ON
H: ON
L: OFF
H: ON
H: ON
L: OFF
H: ON
L: OFF
Table of monitor power LED blinking timing at the time of error occurrence
Error type
Cable error
AVC-side power error
Blinking once: Slow
AVC-side power error
Blinking once: Slow
Lamp error
Blinking once: Fast
Blinking once: Fast
AVC temperature
error
Blinking three times
error
Blinking three times
AVC fan error
Blinking four times
Blinking four times
Monitor temperature
error
Blinking five times
error
Blinking five times
Monitor fan error
Blinking six times
Blinking six times
Monitor 1-bit error
Blinking seven times
Blinking seven times
Monitor power error
Blinking twice
Blinking twice
48
LC-37AD1E
NO
NO
NO
NO
YES
YES
YES
NO
YES
YES
PATTERN R, G and B become effective only when the monitor is started singly. Each can produce a solid
filled screen of 256-level gray scale, which can be used for IC wire connection checking when a certain gray
scale level is not produced.
filled screen of 256-level gray scale, which can be used for IC wire connection checking when a certain gray
scale level is not produced.
Dropout (gray-scale-related)
Set PATTERN1 on the adjustment
process menu to "2". Is the gray
scale pattern displayed correctly?
process menu to "2". Is the gray
scale pattern displayed correctly?
Check the color signal in question
with the gray scale test pattern. Is
there a problem with the contact
and resistance between IC4501
and SC4601-4604?
with the gray scale test pattern. Is
there a problem with the contact
and resistance between IC4501
and SC4601-4604?
Check FFC
connected to
SC4601-4604.
connected to
SC4601-4604.
Perform checking around
IC4501 and SC4601-4604.
IC4501 and SC4601-4604.
Set PATTERN3 on the adjustment
process menu to "1" to "3" (the QS
drive test pattern is displayed). Is
the gray scale displayed correctly?
process menu to "1" to "3" (the QS
drive test pattern is displayed). Is
the gray scale displayed correctly?
Perform checking around
IC4702 and IC4902.
IC4702 and IC4902.
Perform checking between
IC4701 and IC4501.
IC4701 and IC4501.
Perform checking between
IC4901 and IC4501.
IC4901 and IC4501.
Set PATTERN3 on the adjustment
process menu to "4". Is the test
pattern displayed correctly at
intervals of one dot?
process menu to "4". Is the test
pattern displayed correctly at
intervals of one dot?
Set PATTERN3 on the adjustment
process menu to "5". Is the test
pattern displayed correctly at
intervals of one dot?
process menu to "5". Is the test
pattern displayed correctly at
intervals of one dot?
Perform checking between SC2201
and IC2206, between IC2206 and
IC4701 or between IC2206 and
IC4901.
and IC2206, between IC2206 and
IC4701 or between IC2206 and
IC4901.
YES
NO
NO
YES
YES
YES
NO
NO
NO
No picture comes out.
Is the RSET terminal (pin (3))
of IC2206 set to "H"?
of IC2206 set to "H"?
Perform checking around X2201
connected to pin (161) of IC2206.
connected to pin (161) of IC2206.
Is X2201 connected to pin (161) of
IC2206 oscillating (18.26 MHz)?
IC2206 oscillating (18.26 MHz)?
Is IC2202 operating (CONFIG
ROM)?
ROM)?
Perform checking
around IC2202.
around IC2202.
Check X2201 and the
peripheral circuitry.
peripheral circuitry.
Is the clock (91.3 MHz) applied to
TL2202 (pin (102) of IC2206)?
TL2202 (pin (102) of IC2206)?
Is the normal synchronization
signal is applied to TL2202 (pin
(97) of IC2206), TL2203 (pin
(96) of IC2206) and TL2204
(pin (95) of IC2206)?
signal is applied to TL2202 (pin
(97) of IC2206), TL2203 (pin
(96) of IC2206) and TL2204
(pin (95) of IC2206)?
YES
YES
IC2206 is faulty.
Check IC4903 and the ICs
(IC4707, IC4702, IC4901 and
IC4902) downstream from it.
(IC4707, IC4702, IC4901 and
IC4902) downstream from it.
Note that the unit should be replaced when the receiver IC (IC2206), HDCP key ROM (IC2208) or microprocessor
(IC2004) is replaced.
Applicable unit: DKEYHCO16FE52
(IC2004) is replaced.
Applicable unit: DKEYHCO16FE52
49
LC-37AD1E
YES
No
YES
YES
YES
No
YES
No
No
No
Noise is caused to the moving picture when
the QS drive is set to ON.
the QS drive is set to ON.
Is OSTEMP.AD on the 3rd page of the
process adjustment mode set to 255?
process adjustment mode set to 255?
Is the harness connected correctly
between the Thermistor PWB and
Inverter-4 PWB?
between the Thermistor PWB and
Inverter-4 PWB?
Is the board-to-board connected
correctly between the Inverter-3 PWB
and Inverter-4 PWB?
correctly between the Inverter-3 PWB
and Inverter-4 PWB?
Is the harness connected correctly
between the Monitor PWB and
Inverter-3 PWB?
between the Monitor PWB and
Inverter-3 PWB?
Is the input voltage on pin (2) of
IC2004 (microprocessor) 5V?
IC2004 (microprocessor) 5V?
TH6301 thermistor
is faulty.
is faulty.
Check IC4701 and
IC4901 and the peripheral
circuitry.
IC4901 and the peripheral
circuitry.
Connect the harness
correctly or replace it.
correctly or replace it.
Connect the board-to-
board securely or replace
it.
board securely or replace
it.
Connect the harness
correctly or replace it.
correctly or replace it.
Pin (2) of IC2004
(microprocessor) is faulty.
(microprocessor) is faulty.
Click on the first or last page to see other LC-37AD1E (serv.man9) service manuals if exist.