Sharp LC-32SH330E Service Manual ▷ View online
2008-03-14
LC-26SH330, LC-32SH330, LC-42SH330
53
<External input HDMI1>No picture on the display (7)
↓
Does not the picture of the HDMI signal input to HDMI1 go out?
MINI AV_UNIT:
↓
↓
YES
↓NO
YES
↓YES
Is the HOT_PLUG detection function of pin (19) of a HDMI
terminal (CN502) normal?
terminal (CN502) normal?
NO
Check the line between pin (AN16) of IC U401 and CN502.
Refer to “The picture doesn't appear in all modes.”
Check the connection and setup with the external HDMI
Are EDID data pin (6)(SCL) of IC U503 (EEPROM), pin (5)(SDA)
accessed, and is it read from pin (15), pin (16) of a HDMI
terminal(CN502)?
accessed, and is it read from pin (15), pin (16) of a HDMI
terminal(CN502)?
NO
Is access possible in the re-writing or exchange of EDID data of
IC U503?
IC U503?
Check CN502, IC U503 and peripheral circuits.
Is TMDS signal input into pin(AP15, AT15)/RX2-2±,(AR14,
AU14)/RX2-1±, (AP13, AT13)/RX2-0±, (AR12, AU12)/RX2-C± of
IC U401?
AU14)/RX2-1±, (AP13, AT13)/RX2-0±, (AR12, AU12)/RX2-C± of
IC U401?
Check the line between IC U401 and CN502.
NO
LC-26SH330, LC-32SH330, LC-42SH330
54
<External input HDMI2>No picture on the display (8)
↓
Does not the picture of the HDMI signal input to HDMI2 go out?
MINI AV_UNIT:
↓
↓
YES
↓NO
YES
↓YES
<External input VGA>No picture on the display (9)
↓
Does not the picture of the PC IN(ANALOG) video signal input to VGA(15pin-D-SUB terminal) go out?
TERMINAL_UNIT:
↓
MAIN_UNIT:
↓YES
↓YES
Is R/G/B/H/V signal sent to pin (1)/R, (2)/G, (3)/B, (14)/H, (13)/V
of VGA (CN101)?
of VGA (CN101)?
NO
Check the setting of an external input device that connects of
CN101.
CN101.
Refer to “The picture doesn't appear in all modes.”
Is R/G/B/H/V signal sent to pin (AT25)/R, (AU24)/G, (AT23)/B,
(AR22)/H, (AU22)/V of IC U401?
(AR22)/H, (AU22)/V of IC U401?
NO
Check the line between IC U401 and CN101.
Is the HOT_PLUG detection function of pin (19) of a HDMI
terminal (CN505) normal?
terminal (CN505) normal?
NO
Check the line between pin (AL18) of IC U401 and CN505.
Refer to “The picture doesn't appear in all modes.”
Check the connection and setup with the external HDMI
Are EDID data pin (6)(SCL) of IC U504 (EEPROM), pin (5)(SDA)
accessed, and is it read from pin (15), pin (16) of a HDMI
terminal(CN505)?
accessed, and is it read from pin (15), pin (16) of a HDMI
terminal(CN505)?
NO
Is access possible in the re-writing or exchange of EDID data of
IC U504?
IC U504?
Check CN505, IC U504 and peripheral circuits.
Is TMDS signal input into pin(AP19, AT19)/RX3-2±,(AR18,
AU18)/RX3-1±, (AP17, AT17)/RX3-0±, (AR16, AU16)/RX3-C± of
IC U401?
AU18)/RX3-1±, (AP17, AT17)/RX3-0±, (AR16, AU16)/RX3-C± of
IC U401?
Check the line between IC U401 and CN505.
NO
2008-03-14
LC-26SH330, LC-32SH330, LC-42SH330
55
<External input AV1(Component)>No picture on the display (10)
↓
Does not the picture of the component video signal input to Component go out?
TERMINAL_UNIT:
↓
MAIN_UNIT:
↓YES
↓YES
Is Component Y/Pb/Pr signal sent to pin (2)/Y, (4)/Pb, (6)/Pr of
AV1(CN111) ?
AV1(CN111) ?
NO
Check the setting of an external input device that connects of
CN111.
CN111.
Refer to “The picture doesn't appear in all modes.”
Is Component Y/Pb/Pr signal sent to pin (AU26)/Y, (AT27)/Pb,
(AP27)/Pr of IC U401?
(AP27)/Pr of IC U401?
NO
Check the line between IC U401 and CN111.
LC-26SH330, LC-32SH330, LC-42SH330
56
< During external connection > No picture on the monitor (1)
↓
No picture appears on SCART1 - connected monitor during the tuner (U/V) reception.
↓
TERMINAL_UNIT:
↓
↓NO
↓NO
< During external connection > No picture on the monitor (2)
AVOUT:
↓
No picture from SCART1 appears on AVOUT-connected monitor.
NOTE: Normally, if the screen during display is sent to SCART1, no picture is sent to AVOUT.
NOTE: Normally, if the screen during display is sent to SCART1, no picture is sent to AVOUT.
↓
TERMINAL_UNIT:
↓
↓NO
↓NO
Is CVBS signal output into pin (19) of CN151 (SCART1)?
YES
Check the setting of an external input device that connects of
CN151.
CN151.
Refer to “The picture doesn't appear in all modes.”
Is U401 pin (AT31) CVBS signal output into pin (19) of CN151
(SCART1)?
(SCART1)?
YES
Check the line between CN151 and U401.
Checklist:
1) Is the Signal Type (item) in MENU-Option-Input Select equal to Signal Type of an external device? …Set it to “CVBS”, “Y/C”, “RGB”, “AUTO”.
2) Is ANT-CABLE disconnected or connected improperly? …Connect it correctly as per the operation manual.
3) The picture is sent to the monitor in a CVBS signal if the source during display is ATV/DTV, CVBS or Y/C of SCART1, AV3.
1) Is the Signal Type (item) in MENU-Option-Input Select equal to Signal Type of an external device? …Set it to “CVBS”, “Y/C”, “RGB”, “AUTO”.
2) Is ANT-CABLE disconnected or connected improperly? …Connect it correctly as per the operation manual.
3) The picture is sent to the monitor in a CVBS signal if the source during display is ATV/DTV, CVBS or Y/C of SCART1, AV3.
When sent by component, etc., that signal is not sent to the monitor.
4) When the monitor picture is not sent and is not displayed on the monitor, refer to “No picture” for each terminal.
5) The video output from SCART1 is not the monitor output (output of the picture now watching).
5) The video output from SCART1 is not the monitor output (output of the picture now watching).
The picture of the last selected TV channel is always sent to SCART1. (Specification)
Is CVBS signal output into pin (2) of CN140?
YES
Check the setting of an external input device that connects of
CN140.
CN140.
Refer to “The picture doesn't appear in all modes.”
Is CVBS signal output from pin (AP31) of IC U401 into pin (2) of
CN140 ?
CN140 ?
YES
Check the line between CN140 and IC U401.
Checklist:
1) Is the Signal Type (item) in MENU-Option-Input Select equal to Signal Type of an external device? …Set it to “CVBS”, “Y/C”, “AUTO”.
2) The picture is sent to the monitor in a CVBS signal if the source during display is TV, CVBS or Y/C of SCART1, AV3.
1) Is the Signal Type (item) in MENU-Option-Input Select equal to Signal Type of an external device? …Set it to “CVBS”, “Y/C”, “AUTO”.
2) The picture is sent to the monitor in a CVBS signal if the source during display is TV, CVBS or Y/C of SCART1, AV3.
When sent by component, etc., that signal is not sent to the monitor.
3) When the monitor picture is not sent and is not displayed on the monitor, refer to “No picture” for each terminal.
4) The video output from SCART1 is not the monitor output (output of the picture now watching).
4) The video output from SCART1 is not the monitor output (output of the picture now watching).
The picture of the last selected TV channel is always sent to SCART1. (Specification)
Click on the first or last page to see other LC-32SH330E service manuals if exist.