DOWNLOAD Sharp LC-32P70E (serv.man7) Service Manual ↓ Size: 449.25 KB | Pages: 7 in PDF or view online for FREE

Model
LC-32P70E (serv.man7)
Pages
7
Size
449.25 KB
Type
PDF
Document
Service Manual
Brand
Device
TV / LCD / Service adjustments
File
lc-32p70e-sm7.pdf
Date

Sharp LC-32P70E (serv.man7) Service Manual ▷ View online

19
 LC-26GA5E
 LC-32GA5E
  LC-26P70E
  LC-32P70E
  LC-37P70E
SERVICE ADJUSTMENTS
The adjustment values are set to their optimum at the factory before shipping. If by any chance a value should become 
improper or a readjustment is required due to part replacement, make an adjustment according to the following proce-
dure.
1 Entering and exiting the adjustment process mode
1- Unplug the AC power cord of  TV set to force power off.
2- While holding down the “VOL (–)” and “INPUT” keys on the set at once, plug in the AC power cord to turn on the 
    set. The letter K appears on the screen.
3- Next, hold down the “VOL (—)” and “P ( V )” keys on the set at once. Multiple lines of orange characters appearing  
     on the screen indicate that the set is now in the adjustment process mode. If you fail to enter the adjustment process
    mode (the display is the same as normal start up), retry the procedure.
4- To exit the adjustment process mode after the adjustment is done, unplug the AC power cord to force off the  
    power. (When the power is turned off with the remote controller, once unplug the AC power cord and plug it in
    again. In this case, wait 10 seconds  plugging.)
     To remove “K” mode repeat the point 2.
2 Remote Controller Key Operation and Description of Display in Adjustment Process Mode
2.1 Key operation
Remote controller key
Main unit key
Function
P (Λ / V)
P (Λ / V)
Moving an item (line) by one (UP/DOWN)
VOL (+/-)
VOL (+/-)
Changing a selected item setting (+1/-1)
Cursor (UP / DOWN)
  ————
Turning a page (PREVIOUS / NEXT)
Cursor (LEFT / RIGHT)
  ————
Changing a selected line setting (+10/-10) 
INPUT SOURCE 
on remote controller
INPUT button
Input source switching  (toggle switching)
(TV → EXT1 → EXT2 → EXT3 → EXT4 → EXT5)
(Not Operative)
OK
   ————
 Executing a function
Input  mode  is  switched  automatically  when  relevant  adjustment  is  started  so  far  as  the  necessary  input  signal
available.
2.2 Description of display
SERVICE ADJUSTMENTS
Caution:  Use  due  care  in  handling  the  information  described  here  lest  the  users  should
               know how to enter the adjustment process mode. If the settings tampered with in
                 this mode, unrecoverable system damage may result.
Paramenters
Adjustment process menu 
header
Destination
Current color TV system
Currently selected input
Current page title
Current page/ Total pages
   
1/11              [INFO]             TV           AUTO        FIX: AUTO 
MAIN Version
Dev Version
Dev Loader Version
PIC Version
TEMP SENSOR
NORMAL StandBy Cause
ERROR StandBy Cause
LEW05 01.XXX (XXXX/XX/XX  X) X
X.XX
X.X
XX.XX
XXX
XXXXX
[1] 0    XXHXXM
[2] 0    XXHXXM
[3] 0    XXHXXM
[4] 0    XXHXXM
[5] 0    XXHXXM
20
 LC-26GA5E
 LC-32GA5E
  LC-26P70E
  LC-32P70E
  LC-37P70E
19
 LC-26GA5E
 LC-32GA5E
  LC-26P55E
  LC-32P55E
  LC-37P55E
3. Adjustment process mode menu
The character string in brackets [ ] will appear as a page title in the adjustment process menu header.
����� ����� �����
������������
����������������������������������
�������
����
�������������
������������
�������������������
�������������
������������
���������������������
��������������������
���������������������
����������
����������
������
����
�����
������������
�����������������������������������
���������
���������
�������������
����������������������������������
��������������������������������
���������������������
����������������������������������
�������
����
��
�������������
������������
���������������
������
������������������
������
�������������������
�������������������
�������������������������
�������������
�����������������������������������
�������
��������
�������
��������
��������
������������������
�������
�����������������������������������
�������������������������
���������������������
���������������������������
��������������������������
��������������������������������
�������������������������������
�������������������������������
����������������������������
���������������������������
�������������������
����
�����������
��������������
��������
����������
������������
����������������
�����������������
������������
��������
������
������
������
������
��
��
��
������������������������
�������������������������
��������������������
����������������������
�����������������������
��������������������������
��������������������������
���������������������
������������������
�����������
����
�������������
������������������
������
��
�������������������������
��������������������
�������
����
��
��������������
���
��������������������
��������
����
��
�����������
������
������������������������������������������
�����������
���������������
����
�������������
�������������
�������������
�������������
�������������
�������������
�����������������
�����������������
���
���
���
���
���
���
�������
�������
������������������������������������������
������������������������������������������
������������������������������������������
������������������������������������������
������������������������������������������
������������������������������������������
���������������������������������
������������������������������������
��������������
����
��
������������
������������
������������
������������
������������
������������
������������
������������
������������
��������������
�������
����������������������������������������������
����������������������������������������������
����������������������������������������������
����������������������������������������������
����������������������������������������������
����������������������������������������������
����������������������������������������������
����������������������������������������������
����������������������������������������������
���������������������������������
��������������
����
��
������������
������������
������������
������������
������������
������������
������������
������������
������������
��������������
�������
����������������������������������������������
����������������������������������������������
����������������������������������������������
����������������������������������������������
����������������������������������������������
����������������������������������������������
����������������������������������������������
����������������������������������������������
����������������������������������������������
���������������������������������
Page  Line  Item 
Description 
Remarks (Adjustment detail, etc.) 
 
[INFO] 
1/11
1
2
3
4
5
6
7
Main Version 
Dev Version 
Dev Loader Version 
PIC Version  
TEMP SENSOR 
NORMAL STANDBY CAUSE 
ERROR STANDBY CAUSE 
1.xxx (xx/xx/xxxx) x 
x.xx 
x.x
xx.xx 
xxx 
[X]0 
xxHxxM (X5) 
Main microprocessor version (VCTP) 
PIC version  
Temp inside cabinet (near panel)  
Last status which cause standby 
Error standby cause  
Total operating time before error 
 
[INIT] 
2/11
1
2
3
4
5
6
7
8
9
10
FACTORY INIT 
PUBLIC MODE 
Center Acutime 
RESET 
Backlight Acutime 
RESET 
Picture Read Pos X 
Picture Read Pos Y 
Picture Read Signal Type 
Picture Read 
(EURO/UK/ITALY/FRANCE/RUSSIA)ENTER 
OFF/ON 
Xxh xxM 
OFF/ON  
XxH xxM 
OFF/ON  
0
0
PAL/COMP/HDMI/RGB 
ON/OFF 
Initialisation to factory settings 
PUBLIC MODE flag setting 
Main operating hours 
Main operating hours reset 
Backlight operating hours 
Backlight operating hours reset 
x-axis setting of picture data 
y-axis setting of picture data 
Signal type of picture data 
Start/stop of picture data 
 
[PAL. SECAM. N358] 
3/11
1
2
3
4
5
6
7
8
9
RF-AGC ADJ 
PAL+TUNER ADJ 
PAL ADJ 
TUNER ADJ 
CONTRAST SD 
SECAM CB OFFSET 
SECAM CR OFFSET  
TUNER A DAC 
 RF AGC 
ENTER 
ENTER 
ENTER 
ENTER 
32
1
1
32
22
RF AGC auto adjustment  
PALTUNER auto adjustment 
PAL auto adjustment 
TUNER auto adjustment 
SD contrast adjustment 
SECAM contrast adjustment 
SECAM contrast adjustment 
TUNER DAC adjustment 
RF AGC adjustment 
 
[COMP 15K] 
4/11
1
2
COMP 15K ADJ 
COMP 15K CONTRAST 
ENTER 
32
COMP 15K auto adjustment 
Contrast adjustment 
 
[HDTV] 
5/11
HDTV CONTRAST 
32 
Contrast adjustment 
 
[TUNER] 
6/11
TUNER TEST 
ENTER 
Tuning test (tuning into 224.25 MHz) (Not 
Operative) 
 
[M GAMMA INFO] 
7/11
1
2
3
4
5
6
7
8
M GAMMA IN 1 
M GAMMA IN 2 
M GAMMA IN 3 
M GAMMA IN 4 
M GAMMA IN 5 
M GAMMA IN 6 
M GAMMA IN WRITE 
M GAMM IN RESET  
160
320
480
640
800
960
OFF/ON 
OFF/ON 
W/B adjustment, gradation 1 input setting 
W/B adjustment, gradation 2 input setting 
W/B adjustment, gradation 3 input setting 
W/B adjustment, gradation 4 input setting 
W/B adjustment, gradation 5 input setting 
W/B adjustment, gradation 6 input setting 
EEP writing of adjustment values 
Initialisation of adjustment values 
 
[M GAMMA 1-3] 
8/11
1
2
3
4
5
6
7
8
9
10
M GAMMA R 1 
M GAMMA G 1 
M GAMMA B 1 
M GAMMA R 2 
M GAMMA G 2 
M GAMMA B 2 
M GAMMA R 3 
M GAMMA G 3 
M GAMMA B 3 
M GAMMA WRITE 
0
0
0
0
0
0
0
0
0
OFF/ON 
W/B adjustment, gradation 1R adjustment value 
W/B adjustment, gradation 1G adjustment value 
W/B adjustment, gradation 1B adjustment value 
W/B adjustment, gradation 2R adjustment value 
W/B adjustment, gradation 2G adjustment value 
W/B adjustment, gradation 2B adjustment value 
W/B adjustment, gradation 3R adjustment value 
W/B adjustment, gradation 3G adjustment value 
W/B adjustment, gradation 3B adjustment value 
EEP writing of adjustment values 
 
[M GAMMA 4-6] 
9/11
1
2
3
4
5
6
7
8
9
10
M GAMMA R 4 
M GAMMA G 4 
M GAMMA B 4 
M GAMMA R 5 
M GAMMA G 5 
M GAMMA B 5 
M GAMMA R 6 
M GAMMA G 6 
M GAMMA B 6 
M GAMMA WRITE 
0
0
0
0
0
0
0
0
0
OFF/ON 
W/B adjustment, gradation 4R adjustment value 
W/B adjustment, gradation 4G adjustment value 
W/B adjustment, gradation 4B adjustment value 
W/B adjustment, gradation 5R adjustment value 
W/B adjustment, gradation 5G adjustment value 
W/B adjustment, gradation 5B adjustment value 
W/B adjustment, gradation 6R adjustment value 
W/B adjustment, gradation 6G adjustment value 
W/B adjustment, gradation 6B adjustment value 
EEP writing of adjustment values 
21
 LC-26GA5E
 LC-32GA5E
  LC-26P70E
  LC-32P70E
  LC-37P70E
20
 LC-26GA5E
 LC-32GA5E
  LC-26P55E
  LC-32P55E
  LC-37P55E
4 Special Features
- ERROR STAND-BY CAUSE (Page 1/11) 
  When the unit enters standby due to operational error, total time before the error and the cause of error is recordered
  on EEPROM, if possible. The values can be used to locate the fault for repair.
- EEP CLEAR (Page 10/11)
  Restore NVM data to default values.  
- EEP CLEAR B (Page 10/11)
  Restore NVM data to default values except adjustment data.
5 Video Signal Adjustment Procedure
The adjustment process mode menu is listed in Section 3.
5.1. Signal check
Signal generator level adjustment check (Adjustment to the specifiedd level).
- Composite signal PAL 
:  0.7Vp-p ± 0.02Vp-p (Pedestal to white level)
- 15K Component signal 
:  Y level 
 
0.7Vp-p ± 0.02Vp-p (Pedestal to white level)
  (50Hz) (576i/50Hz)  
   PB, PR level   
0.7Vp-p ± 0.02Vp-p
����� ����� �����
������������
����������������������������������
������
�����
����������
������������
���������������������
���������������������
�������
��������
������������
�����������
��������
�������
�������
�������
���
����
���
�����
�����������������������������������
������������������������������������������
����������������
�������������������������������������
����������������������������������������������������
���������������������������������������
���������������������������������
�������������������
�����������������������������������������
���������
����
�����
������������
������������
������������
������������
���������
���������
���������
��
��
���
���
5.2. Entering the adjustment process mode
Enter the  adjutment process mode according to Section
 1.
5.3. RF AGC Adjustment
���������������� ���������������������
��������������������
�������
��������
���
���������������
������������
����������
�����
��������������� �������������������������
�����������
�������������������������������������������������
����������������
±
�����µ������������
�������������������������������������������������
���������������������������������������
��������
�����������
Page  Line  Item 
Description 
Remarks (Adjustment detail, etc.) 
 
[ETC] 
10/11
1
2
3
4
5
6
7
8
9
10
EEP CLEAR 
EEP CLEAR B 
STAND BY CAUSE RESET 
AUTO INSTALLATION SW 
OPTION 
COUNTRY 
L ERR RESET 
L ERR STOP 
DTV CLR 
I2C-OFF 
OFF/ON 
OFF/ON 
OFF/ON 
0/1
0
AUTO
0
0/1
ENTER 
ENTER
Restore NVM data to default values 
Restore NVM data to default values except 
adjustment data 
Clearing of standby cause error list 
0: unfinished    1:finish (The setting takes effect 
the next time the power is turned on.) 
AUTO: defects the actual region. 
Lamp error counter 
Stops Lamp Error feature (Not operative) 
BUS STOP 
 
LCD 
11/11
1
2
3
4
5
6
7
OSC FREQ 50 
OSC FREQ 60 
PWM FREQ 50 
PWM FREQ 60 
PWM FREQ 
PWM DUTY 
PWM CTRL 
62
62
0
0
409
227
0
50
22
 LC-26GA5E
 LC-32GA5E
  LC-26P70E
  LC-32P70E
  LC-37P70E
21
 LC-26GA5E
 LC-32GA5E
  LC-26P55E
  LC-32P55E
  LC-37P55E
5.4. PAL Signal & Tuner Adjustment
���������������� ���������������������
��������������������
�������
��������
���
��������������������
����������������������
����������
�������������
�����
��������������� �������������������������
�����������
� �����������������������������������������������������������������������
���������
� ��������������������������������������������
� �������������������������������������������������������������������������
������������������
��������������������������� ���������������������������
������� ���������������
����������������������
���������������������������������
��������
�����������
�����������
�����������������
5.5. ADC Adjustment (Component 15K)
����������������������������������
���������������� ���������������������
��������������������
����������
������������������
�������������
������������������������
����������
���� �����������
��������������� �������������������������
�����������
� �������������������������������������������������������������������
���������������������������������
��������������������������������������������������
����������������������������������������
���������� �
�����
6 White Balance Adjustment
Adjustment procedure Page 7/11 shows the value of adjustment gradation (IN value) and Adjustmnet procedure Page 
8/11 & 9/11 show adj. offset value (initial value : 0). White balance adjustment is executed adjusting the adj. offset value, 
indicated on Page 8/11 & 9/11.
Condition of the inspection: • Backlight: MAX (+8) [DYNAMIC]
 
 
 
      
  • Colorimeter at screen centre
Adjustment reference device: Minolta CA-210
Adjustment spec.  ±0.004,     Inspection spec. : ±0.006   (GAMMA 1)
Adjustment spec.  ±0.002,     Inspection spec. : ±0.004   (GAMMA 2...6)
  
Adjustment: Check that the values on page 7/11 of process adjustment are set as below. If not, change them accor-
dingly. 
Page of 7
Display

Sharp LC-32P70E (serv.man7) Service Manual ▷ Download

  • DOWNLOAD Sharp LC-32P70E (serv.man7) Service Manual ↓ Size: 449.25 KB | Pages: 7 in PDF or view online for FREE
  • Here you can View online or download the Service Manual for the Sharp LC-32P70E (serv.man7) in PDF for free, which will help you to disassemble, recover, fix and repair Sharp LC-32P70E (serv.man7) LCD. Information contained in Sharp LC-32P70E (serv.man7) Service Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.