DOWNLOAD Sharp LC-32LE210E (serv.man22) Service Manual ↓ Size: 12.49 MB | Pages: 36 in PDF or view online for FREE

• 

 has not been created as a real recording 

method, so the recorded data will be deleted each time 
you cancel it, change programme or input source, or 
switch off the TV. The recorded data will never be available 
for any external device.

• 

During  TimeShift mode, 

p, “EPG” and m show live 

broadcast information, not recorded one.

• 

Keeping “ALWAYS” mode as a permanent option

 

may 

shorten the life of the external USB memory.

• 

Programmes which require a PIN to watch them cannot be 
recorded with TimeShift function until you enter the PIN. 

USB REC can activate immediately recording by using 
REC

 on the remote control, or with a timer using data 

taken from EPG or programming an event manually. To 
use either method follow the instructions below:

● 

● 

The recording starts when user decides:

 

Press REC on the remote control to start recording 
the current programme. REC symbol appears in 
the bottom left corner of the screen.

 

To stop recording the current programme, press 
END

 twice, change TV programme or input source, 

or switch- off the TV set.

 

Press 

/

 to playback the programme being 

recorded. The TV set continues recording the 
broadcast while you are watching the recorded 
programme. The TV set shows 

I

 symbol on the 

screen. 

 

Press 

/

 during playback to pause. The TV shows 

the symbol 

F

 on the screen.

 

Press 

V

 playback to fast forward. By pressing 

V

 key repeatedly, allows you to select the fast 

forward. By pressing 

L

 key the recording fast 

forwards in intervals of fi ve minutes. Press 

/

 to 

restore the normal speed.

 

Press 

S

 during playback to rewind. By pressing 

S

 key repeatedly, allows you to select the rewind 

speed. By pressing 

T 

key the recording rewinds 

in intervals of five minutes. Press 

/

 to restore the 

normal speed.

Press  END during playback mode to stop the 
playback and return to recording mode of current 
programme. The TV set continues recording and 
the REC symbol is shown on the screen.

While the recording is activated the REC symbol, the 
recording progress bar or playback progress bar will be 
displayed.

The bar shows the recording start time, current time 
and expected end, and the remaining recording time.

                                                                                

 

••••••••••

••••••••••••••••••••••••••••••••••••••••••   



REC

[hhhh:mm:ss]

● 

● 

It can be programmed a recording by using two 
methods. Using the programme guide (EPG) or manually 
with the option “USB REC Manual Temporization” 
on the menu TIME.

1 Programming a timer with the EPG

1. Press EPG to select the programme you want to 

record. Then press REC.

2.  Set up the recording parameters (auto, once, every 

day or weekly) and press OK to confi rm.

2 Programming with “USB REC Manual 

1. To activate a timer recording use the menu 

option  TIME and the option USB REC Manual 
Temporization

.

2.  Set up the desired recording parameters (channel, 

mode, date, start time and end) and press OK.

● 

● 

The timings will be stored in the USB REC 
Programmed Recording List

 in the TIME 

menu, pending to be executed.

All the fi nished recordings are available on the 
“USB REC Recorded List” in the TIME menu, or 
they are also accessible by pressing REC LIST key 
on the remote control. 

The TV set can start a timer recording while is in 
standby mode. When the recording starts in this 
mode, the status indicator (AQUOS pyramid) will 
change from red to violet.

• 

If you try to switch off the TV (

B)  during a USB recording, 

an on screen menu will appear where you can decide to 
switch off completely or continue with the recording until 
the maximum capacity of the USB device is reached. If 
you choose to continue with the recording, the TV will 
switch off, but continue to show the pyramide icon lit in 
purple.

The timer recordings are not possible when the TV 
set is off, this is when the status indicator (AQUOS 
pyramid) is not lit. 

● 

● 

To delete non desired recordings stored in USB device, 
follow the instructions below:

1. Press REC LIST on the remote control.

2. Select the recording you want delete.

3. Press RED button on the remote control. 

• 

The USB REC recording function does not work for ATV 
channels or external inputs.

• 

It can appear displaying troubles during rewind or 
fast forward modes, depending on the USB memory 
characteristics.

• 

The recorded data will be never available for any external 
device (computer) or in other TV even if it is the same 
model. The recordings only can be displayed in the same 
TV in which they were made.

• 

Programmes wich require a PIN to watch them cannot be 
recorded until you enter the PIN.

•  While TimeShift is activated, USB REC will be 

disconnected. It is recommended  to enable immediate 
recording (REC) instead of TimeShift 

/

, if you are 

not sure when you are going to watch the recorded 
programme.

 

Analogue TV

Consumer Electronics Control

Digital Noise Reduction

Digital TV

Cable Digital TV

Digital Video Broadcasting-Terrestrial

Digital Video Broadcasting-Cable

Digital Visual Interface

Electronic Pogramme Guide

High-bandwidth Digital Content Protection

High-Definition Multimedia Interface

Multimedia and Hypermedia Expert Group

On Screen Display

Pulse Code Modulation

Universal Serial Bus

Wide Screen Signalling

• No power.

•  Check if you pressed 

B on the remote control unit.

If the indicator on the TV lights up red, press 

B.

•  Is the AC cord disconnected?
•  Check if you pressed 

a on the TV.

•  The TV cannot be operated.

•  External influences such as lightning, static electricity, etc., may cause improper operation. In this 

case, operate the TV after first turning off the power, or unplugging the AC cord and re-plugging 
it in after one or two minutes.

•  Remote control unit does not operate.

•  Are batteries inserted with polarity (

e, f) aligned?

•  Are batteries worn out? (Replace with new batteries.)
•  Are you using it under strong or fluorescent lighting?
•  Is a fluorescent light illuminating to the remote control sensor?

•  Picture is cut off.

•  Is the image position correct?
•  Are screen mode adjustments (Aspect ratio) such as picture size made correctly? (Page 23.)

•  Strange colour, light colour, or dark 

colour, or colour misalignment.

•  Adjust the picture tone.
•  Is the room too bright? The picture may look dark in a room that is too bright.
•  Check the “PICTURE” setting (Page 19).

•  Power is suddenly turned off.

•  The TV’s internal temperature has increased.

Remove any objects blocking the vent or clean.

•  Is the “Sleep Timer” set? Select “Off” from the “TIME” menu (Page 20).
•  Is “No Signal Off” or “No operation Off” activated?

•  No picture.

•  Are connections to external equipment correct? (Pages 13, 14 and 15)
•  Is the input signal type selected correctly after connection? (Page 10)
•  Is the correct input source selected? (Page 10)
•  Is the picture adjustment correct? (Pages 19)
•  Is the antenna connected properly? (Page 8)

•  No sound.

•  Is the volume too low?
•  Make sure that headphones are not connected.
•  Check if you pressed 

e on the remote control unit.

•  The TV sometimes makes a cracking 

sound.

•  This is not a malfunction. This happens when the cabinet slightly expands and contracts 

according to changes in temperature. This does not affect the TV’s performance.

•  When the TV is used in a low temperature space (e.g. room, office), the picture may leave trails or appear slightly delayed. 

This is not a malfunction, and the TV will recover when the temperature returns to normal.

•  Do not leave the TV in a hot or cold location. Also, do not leave the TV in a location exposed to direct sunlight or near a 

heater, as this may cause the cabinet to deform and the LCD panel to malfunction.
Storage temperature: -20 °C to 

e60 °C.

The software included in this product is comprised of various software components whose individual copyrights are held by 
SHARP or by third parties.

The copyrights for the software components and various relevant documents included with this product that were developed 
or written by SHARP are owned by SHARP and are protected by the Copyright Act, international treaties, and other relevant 
laws. This product also makes use of freely distributed software and software components whose copyrights are held by third 
parties. 

•  This TV should be fixed on a wall only with the wall fix bracket available from SHARP (Page 5). The use of other wall 

•  Fixing the LCD colour TV requires special skills and should only be performed by qualified service personnel. 

•  You can ask qualified service personnel about using an optional bracket to fix the TV on a wall.
•  To use this TV fixed on a wall, first remove the adhesive tape at the two locations on the rear of the TV, and then use the screws 

supplied with the wall fix bracket to secure the bracket to the rear of the TV.

•  When you fix the TV on a wall, you should attach the supporting post.

*1 Measured according to IEC 62087 Ed. 2.
*2 For further information about the Energy Save function, 

please see related pages in this operation manual.

*3 Measured according to IEC 62301 Ed. 1.
*4 Measured according to IEC 62301 Ed. 1.
*5 Annual energy consumption is calculated on the basis 

of the On-Mode (HOME MODE) power consumption, 
watching TV 4 hours a day, 365 days a year.

*6 Annual energy consumption is calculated on the basis of 

the Energy-Save-Mode power consumption, watching TV 
4 hours a day, 365 days a year.

NOTE
•  The power consumption of On-Mode varies depending on the images the TV displays.

LCD Panel

24"   BLACK TFT LCD LED TV

32”   BLACK TFT LCD LED TV

Resolution

6.220.800 dots (1.920 x 1.080 pixels)

Video Colour System

PAL/SECAM/NTSC 3.58/NTSC 4.43/PAL 60

TV 
Func-
tions

TV Standard

Analogue

CCIR (B/G, I, D/K, L/L’)

Digital

DVB-T (2K/8K OFDM)(H.264), DVB-C (Only Lx220)

Receiving Channel

VHF/UHF

E2–E69 ch, F2–F10 ch, I21–I69 ch, IR A–IR J ch (Digital: IR A ch–E69 ch)

CATV

Hyper-band, S1–S41 ch

TV-Tuning System

Auto Preset 999 ch: non-Nordic / 9999 ch: Nordic (ATV: 99 ch), Auto Label, Auto Sort

STEREO / BILINGUAL

NICAM/A2

Viewing angles

H: 176°, V: 176°

Audio Amplifi er

6 W x 2

10 W x 2

Speaker

(25 mm x 100 mm) x 2

(30 mm x 100 mm) x 2

Terminals

TV Antenna

UHF/VHF 75 Ω Din type (Analogue & Digital)

SERVICE

Ø 3.5 mm jack

SCART

SCART (AV input, RGB input, TV output, Y/C input)

PC INPUT

VGA  (D-Sub 15pin), Ø 3.5mm jack

COMPONENTS

COMPONENT IN: Y/PB(CB)/PR(CR), RCA (AUDIO R/L)

HDMI1 

HDMI, Ø 3.5mm jack

HDMI2 

HDMI, Ø 3.5mm jack

HDMI3

HDMI, Ø 3.5mm jack

AV

RCA connector (AV input)

MEDIA PLAYER/ TIME-SHIFT/
USB REC

USB 2.0 HOST (A type)

DIGITAL AUDIO OUTPUT

RCA S/PDIF digital audio output.

C. I. (Common Interface)

EN50221, R206001, CI+ specifi cation (Only Lx220)

Headphones

Ø 3.5 mm jack (Audio output)

OSD language

Czech, Danish, Dutch, English, Estonian, Finnish, French, German, Greek, Hungarian, Italian, 
Latvian, Lithuanian, Norwegian, Polish, Portuguese, Russian, Slovak, Slovene, Spanish, 
Swedish, Turkish, Ukrainian, Byelorussian, Romanian.

Power Requirement

AC 220–240 V, 50 Hz

Power Consumption (IEC62087 Method)

30W (0.25 W Standby)

85W (0.25 W Standby)

Weight

4,9 Kg (Without stand), 6 Kg (With stand)

8,5 Kg (Without stand), 9,8 Kg (With stand)

Operating Temperature

0 °C to +40 °C

*1 On-Mode (W) (HOME MODE)

25 W

63 W

*2 Energy-Save-Mode (W) 

ECO

22 W

48 W

*3 Standby-Mode (W)

0.25 W

0.25 W

*4 Off Mode (W) 

0.18 W

0.18 W

*5 Annual Energy Consumption (kWh)

 37 kWh

92 kWh

*6 Annual Energy Consumption    
    Energy-Save-Mode (kWh) 

ECO

31 kWh

71 kWh