DOWNLOAD Sharp LC-32LE210E (serv.man22) Service Manual ↓ Size: 12.49 MB | Pages: 36 in PDF or view online for FREE

•  In cases when the decoder needs to receive a signal from 

the TV, make sure to select the appropriate input terminal to 
which the decoder is connected in “Input Source” (Page 10).

● VCR ● Decoder 

● DVD player/recorder

Connect an amplifier with external speakers as shown 
below.

SCART cable

Audio cable

Digital audio output setting
After connecting an amplifier with digital audio input 
and external speakers as shown, you should set an 
audio output format compatible with the programme 
you are watching or the device connected.

Go to “MENU” > “SOUND” > “SPDIF Mode” 
> select “PCM” or “Dolby Digital”.

NOTE
• When you set this to “Dolby Digital”, and you 

receive the Dolby Digital or Dolby Digital Plus 
audio formats, Dolby Digital audio is output. 
Otherwise, PCM audio is output.
When you set this to “PCM”, PCM audio is output 
no matter what audio formats you receive.

●

Connecting an amplifier with digital audio 

input

SPDIF

ø 3,5 mm stereo mini jack cable

HDMI 1, 2 or 3

HDMI-certified cable

DVI/HDMI Cable

PC

PC

ø 3,5 mm stereo 

mini jack cable

VGA cable

You can select the picture size.

 

Press MENU

 on the remote control.

 

Press 

▼ key to select “Aspect ratio”.

 

Press 

► key to select the desired item.

Keeps the original aspect ratio in a full 
screen display

An image fully fi lls the screen

Displays an image with the same 
number of pixels on the screen

•  You can also select an item by pressing 

f on the remote 

control unit. 

•  Connect the PC before making adjustments.

•  Selectable picture size may vary with input signal type.
• The “Aspect ratio” adjustment is only available for analogue 

signals through the “PC IN” terminal.

•  When using the PC-IN terminal is necessary to connect a 

audio cable.

DVI/VGA Conversion cable

ø 3,5 mm stereo 

mini jack cable

● If after connecting a PC to the TV through a HDMI 
cable, the audio does not run, connect a mini stereo 
connector of ø 3.5mm between TV and PC as 
indicated in the previous drawing

.

 

●  When a PC is connected to the TV with a DVI 
cable, it will be necessary to connect a mini stereo 
connector of ø 3.5mm of the TV to PC as indicated 
in the previous drawing.

AUDIO IN

HDMI (DVI)

VGA

640 

g 480

31,5 kHz

60 Hz

VGA

720 

g 400

31,47 kHz

70 Hz

SVGA

800 

g 600

37,9 kHz

60 Hz

XGA

1.024 

g 768

48,4 kHz

60 Hz

WXGA

1.360 

g 768

47,7 kHz

60 Hz

SXGA

1.280 

g 1.024

64,0 kHz

60 Hz

SXGA+

1.400 

g 1.050

65,3 kHz

60 Hz

UXGA

1.600 

g 1.200

75,0 kHz

60 Hz

1080p

1.920 

g 1.080

67,5 kHz

60 Hz

•  This TV has only limited PC compatibility, correct operation 

can only be guaranteed if the video card conforms exactly to 
the VESA 60 Hz standard. Any variations from this standard 
may result in picture distortions.

VGA, SVGA, XGA, WXGA, SXGA, SXGA+ and 
UXGA are registered trademarks of International 
Business Machines Corporation.

 

 

This function enables the screen to be automatically 
adjusted to its best possible condition when the 
analogue terminals of the TV and PC are connected 
with a commercially available DVI/VGA conversion 
cable, etc.

Press 

b  to select “PC-RGB” from INPUT 

, and then press OK.

Press MENU key and go to PICTURE 

s Screen 

s Auto adjust, and then press OK.

•  When connect a PC and select PC-RGB source, the 

is executed automatically. 

may fail if the PC image has low 

resolution, has unclear (black) edges, o is moved 
while executing “Auto adjust”.

•  Be sure to connect the PC to the TV and switch it on 

before starting “Auto adjust”.

can be executed only when inputting 

analoque signals through the “PC IN” terminal.

Ordinarily you can easily adjust the picture as necessary 
to change image position using “Auto adjust”. In 
some cases, however, manual adjustment is needed 
to optimise the image.

Press 

b  to select PC-RGB from INPUT 

, and then press OK.

Press MENU key and go to PICTURE 

s Screen.

Press 

▲/▼ to select the specific adjustment item.

Press 

◄/►  to adjust the item to the desired 

position.

Centres the image by moving it to the 
left or right.

Centres the image by moving it up or 
down.

Changes the image size.

Adjusts when characters have low 
contrast or when the image fl ickers.

• The “Screen” options in the “PICTURE” menu can be 

adjusted only when inputting analogue signals through the 
“PC IN” terminal.

•  The menu options differ in the selected input modes, but the operating procedures are the same.
•  The screens in the operation manual are for explanation purposes (some are enlarged, others cropped) and may vary slightly from 

the actual screens.

•  Items in darker grey cannot be selected.

•  You need to call up the OSD to perform settings for the TV. The OSD for the settings is called menu.
•  The menu enables various settings and adjustments.
•  The menu can be operated with the remote control unit and with the TV panel control keys.

The Guide Display at the bottom of the screen shows 
operations with the OSD.

The bar above is an operational guide for the remote 
control unit. The bar will change in accordance with 
each menu setting screen.

 Picture mode        User           Eco

This function is useful when there is no 
remote control unit within your reach.

 

Press MENU and the “PICTURE” 
screen displays.

 

Press P

r/s instead of 

a/b or 

i

k/l instead of c/d to select 

the item.

 

Press 

b to complete the setting.

•  The “PICTURE” screen will disappear if left unattended for 

several seconds.

Press MENU and the “PICTURE” 
screen displays.

The operation will exit the menu 
screen if you press END before it is 
completed.

Press 

a/b/c/d to select/adjust the 

desired menu, and adjust the item to 
the desired level, and then press OK.

Press MENU to return to the previous 
page.

E

E