Sharp LC-30HV2E (serv.man2) Service Manual ▷ View online
54
LC-30HV2E
Ë
VHiNJM2193M-1Y (IC3802)
»
Focus & SRS Audio Processor
»
Block Diagram
1.SRSINR
16.V+
2.WIDTHR
17.MODE2
3.SRSFILTERR
18.MODE1
4.SRSOUTR
19.FOCUSOUTL
5.FOCUSINR1
20.LPFIN
6.FOCUSINR2
21.LPFOUT
7.LFOUTR
22.HFINL
8.LFINR
23.LFINL
9.HFINR
24.LFOUTL
10.BCOUT
25.FOCUSINL2
11.BCIN
26.FOCUSINL1
12.FOCUSOUTR
27.SRSOUTL
13.REFIN
28.SRSFILTERL
14.VREF
29.WIDTHL
15.GROUND
30.SRSINL
1
15
30
16
LF
Elevation
Filter
Elevation
Filter
LF
Elevation
Filter
Elevation
Filter
HF
Elevation
Filter
Elevation
Filter
HF
Elevation
Filter
Elevation
Filter
BYPASS
FOCUS
FOCUS
BYPASS
Bass Compensation
Control
Control
LF
Elevation
Control
Elevation
Control
SRS
BYPASS
SRS
BYPASS
SRS Filter
WIDTH
Control
Control
SRS
Rch IN
Rch IN
SRS
Lch IN
Lch IN
FOCUS Lch IN
FOCUS Rch IN
SRS Rch OUT
SRS Lch OUT
FOCUS
Lch OUT
Lch OUT
FOCUS
Rch OUT
Rch OUT
FOCUS
Control
Control
Bass
Compensation
Filter
Compensation
Filter
»
Pin Function
55
LC-30HV2E
Ë
VHiTA1101B/-1Y (IC3809)
»
Stereo Amp.
»
Pin Function
Pin
Functi on
Descri pti on
1, 2
DCAP2, DCAP1
Charge pump switching pins. DCAP1 (pin 2) is a free running 300kHz square
wave between VDDA and DGND (12Vpp nominal). DCAP2 (pin 1) is level shifted
10 volts above DCAP1 (pin 2) with the same amplitude (12Vpp nominal),
frequency, and phase as DCAP1.
wave between VDDA and DGND (12Vpp nominal). DCAP2 (pin 1) is level shifted
10 volts above DCAP1 (pin 2) with the same amplitude (12Vpp nominal),
frequency, and phase as DCAP1.
3, 8
V5D, V5A
Digital 5VDC, Analog 5VDC
4, 7,
15
AGND1, AGND2,
AGND3
Analog Ground
5
REF
Internal reference voltage; approximately 1.0 VDC.
6
OVERLOADB
A logic low output indicates the input signal has overloaded the amplifier.
9, 12
VP1, VP2
Input stage output pins.
10, 13
IN1, IN2
Single-ended inputs. Inputs are a ìvirtualî ground of an inverting opamp with
approximately 2.4VDC bias.
approximately 2.4VDC bias.
11
MUTE
When set to logic high, both amplifiers are muted and in idle mode. When low
(grounded), both amplifiers are fully operational. If left floating, the device stays in
the mute mode. Ground if not used.
(grounded), both amplifiers are fully operational. If left floating, the device stays in
the mute mode. Ground if not used.
14
BIASCAP
Input stage bias voltage (approximately 2.4VDC).
16
SLEEP
When set to logic high, device goes into low power mode. If not used, this pin
should be grounded
should be grounded
17
FAULT
A logic high output indicates thermal overload, or an output is shorted to ground,
or another output.
or another output.
18, 28
PGND2, PGND1
Power Grounds (high current)
19 DGND
Digital
Ground
20, 22;
25, 23
OUTP2 & OUTM2;
OUTP1 & OUTM1
Bridged outputs
21, 24
VDD2, VDD1
Supply pins for high current H-bridges, nominally 12VDC.
26 NC
Not
connected
27
V
DDA Analog
12VDC
29
CPUMP
Charge pump output (nominally 10V above VDDA)
30
5VGEN
Regulated 5VDC source used to supply power to the input section (pins 3 and 8).
5VGEN
SLEEP
FAULT
PGND2
DGND
OUTP2
VDD2
OUTM2
OUTM1
VDD1
OUTP1
NC
VDDA
PGND1
CPUMP
DCAP2
AGND3
BIASCAP
IN2
VP2
MUTE
IN1
VP1
V5A
AGND2
OVERLOADB
REF
AGND1
V5D
DCAP1
30
16
17
18
19
20
21
22
23
24
25
26
27
28
29
1
15
14
13
11
10
12
9
8
7
6
5
4
3
2
30-pin Power SOP Package
(Top View)
56
LC-30HV2E
TROUBLE SHOOTING TABLE
No Power
LCD LED: ON
AVC-C LED: OFF
Check power switch, AC power cable and power unit of AVC-C.
LCD LED: OFF
AVC-C LED: ON
Check power switch, AC power cable and power unit of LCD.
LCD LED: BLINKING
(Once per second)
Check system cable, power switch, AC power cable and power unit of AVC-C.
LCD LED: BLINKING
(4 times per second)
Check cooling fan, IC2102 and peripheral circuits.
LCD LED: ON IN RED
AVC-C LED: ON IN RED
LCD LED never turns to
green.
Check power switch, AC power cable and power unit of LCD.
AVC-C LED never turns
to green.
Check power switch, AC power cable and power unit of AVC-C.
LCD panel backlight
never lights up.
Reset the lamp error count. (See adjustment procedure.)
Check Q6551, Q6554, Q6557, Q6560, Q6563, and Q6566 as well as peripheral circuits.
Initialize EEPROM. (See
adjustment procedure.)
If not successful: Check power switch, AC power cable and power unit of LCD.
57
LC-30HV2E
No sound
No sound from speaker
NO
YES
YES
Does output icon denote speaker
when operating audio volume control?
NO
NO
Does output icon denote lineout when
operating audio volume control?
Monitor output in the main menu is set
to "V
ariable". Switch it to "Fixed".
YES
Is audio output available at each related
pin of IC2501 (MUL
TI SOUND
PROCESSOR) normal?
Pins (36) and (37) of IC2501 (SC1 OUT
L/R)
YES
Check Q2505 and 2504 (Buf
fer) and
its peripheral circuits
YES
Check PC I/F Unit and its peripheral
circuits.
No audio output (SCAR
T1)
YES
Is audio output available at each
related pin of IC2501 (MUL
TI SOUND
PROCESSOR) normal?
Pins (27) and (28) of IC2501
(SC1 OUT
L/R)
YES
Check the circuit between pins (27) and
(28) of IC2501 and pins (3) and (1) of
SCAR
T1, as well as audio mute circuit.
NO
Is tuner audio input available at each
related pin of IC2501
(MUL
TI SOUND PROCESSOR) normal ?
Pin (67) of IC2501 (SOUND IF1)
Pin (69) of IC2501 (SOUND IF2)
NO
NO
NO
Is audio output available at each related pin of
IC1301 (A
V SWITCH) normal?
Pins (52) and (54) of IC1301 (L/R OUT1)
Pins (43) and (45) of IC1301 (L/R OUT2)
Pins (38) and (40) of IC1301 (L/R OUT3)
NO
No audio output (SCAR
T2/3)
YES
Is audio output available at each
related pin of IC2501 (MUL
TI SOUND
PROCESSOR) normal?
Pins (27) and (28) of IC2501
(SC1 OUT
L/R)
YES
Check the circuit between pins (27) and
(28) of IC2501 and pins (3) and (1) of
SCAR
T2/3, as well as audio mute circuit.
No monitor audio output
YES
Is normal audio output available at
each related pin of IC2501
(MUL
TI SOUND PROCESSOR)?
Pins (34) and (33) of IC2501
(SC2 OUT
L/R)
YES
Check the circuit between pins (34) and
(33) of IC2501 and J1
101 (monitor audio
output), as well as audio mute circuit.
On TV reception
On external input / PC input
Check IC2501 (MUL
TI SOUND PROCESSOR) and its peripheral circuits.
Check B.P
.F
. of SIF1 and SIF2 respectively.
Check
TU1
101 (U/V tuner) and peripherals.
Is each audio input circuit of IC1301 (A
V SWITCH)
normal?
Between SCAR
T1 Pins (6), (2) and IC1301 Pins (2), (4)
Between SCAR
T2 Pins (6), (2) and IC1301 Pins (9), (1
1)
Between SCAR
T3 Pins (6), (2) and IC1301 Pins (16), (18)
Between front input (J3401) and IC1301 Pins (23), (25)
Between PC input (J3403) and IC1301 Pins (29), (31)
Check IC1301 (A
V SWITCH) and peripherals.
2
TROUBLE SHOOTING TABLE
(Continued)
Click on the first or last page to see other LC-30HV2E (serv.man2) service manuals if exist.