DOWNLOAD Sharp LC-26GA6E (serv.man2) Service Manual ↓ Size: 30.33 MB | Pages: 127 in PDF or view online for FREE

Use the up / down arrows to select a term in the 
menu.
Confi rm the selection with 

Use the left / right arrows to change between pa-
rameters.
Use the up / down arrows to change values.

Press END button to return to the previous menu.

To change NVM values.

ADDR:  

 

NVM address.

VAL:  NVM 

Value.

SAVE: 

 

Save NVM changes.

Unprotect the EDID, that contains the recognizable formats of screen for HDMI.

ERASE:     

If you select YES and Turn OFF-ON the TV by main switch,  the data of NVM will be recorded  

 

 

 

to the default  values .

In

 ADDR option of this menu, by using the colour buttons of R/C is possible to pass directly to A, B, C or D param-

eter.
Note: DO NOT change any NVM data, unless you have been advised to do by a Sharp representative. If data is 
incorrectly changed, serious damage may occur to the receiver.

To select QS peripherals ICs. ( 0:LCD Controller / 1:QS Driver / 2: Extended Digital Analog Converter / 

 

 

 3: EEprom Microcontroller / 4: Reserved)

Address of register.

Read mode: Display data after executing “SEND” / Write mode: Select data to write.

Select Read or Write. ON: write     OFF: read.

Send data to QS.

Use the up / down arrows to select a term in the 
menu.
Confi rm the selection with 

Use the up / down arrows to change values.
Use the left / right arrows to change between pa-
rameters.

IC Cont Menu (NOT OPERATIVE)
Send specifi c data to the QS board.

Press END button to return to the previous menu.

GA6  VX.XX  ExpX
PxW Exp X.X LCD VXX

GA6  VX.XX  ExpX
PxW Exp X.X LCD VXX

M  T

FREQ: Change between 50/60Hz and PC.
CLR MODE: When press OK key send the value to monitor microcontroller. 
PATTERN1: Choose pattern to adjust QS.
PATTERN2: Choose pattern to adjust QS.
COMBIAS: Specifi c adjustment for QS. COMMON BIAS adjusting value is displayed.
IC CONT: See the next OSD.
SOFT VER.: Software version of QS IC. Display the version of monitor microcontroller.

COMBIAS Adjustment
Select COMBIAS and press the “OK” button so that the fl icker screen will appear.
Adjust the fl icker on the screen to minimum with up / down buttons  on the remote control. At this time, press the “OK” 
key to complete the adjustment.

GA6  VX.XX  ExpX
PxW Exp X.X LCD VXX

Use the up / down arrows to select a term in the 
menu.
Confi rm the selection with 

Press END button to return to the previous menu.

CPLD: NOT OPERATIVE
STOP BUS: Stop IC communication. 
EXT 2 RGB: Enable or disable the RGB entry over EXT2 connector.
FLASH UPGRADE: Select ON to update to software update. (See page 23) 
RAM TEST: Check the RAM memory. It is working correctly when “OFF” appear on the screen.  If any number appear, 
the memory is not working correctly.

Counters Menu
To see information about TV.

GA6  VX.XX  ExpX
PxW Exp X.X LCD VXX

SW FROM MAINS: Number of times that  turn on  the TV by the main switch.
SW ON TIMES: Number of times that  switch on  the TV by the R/C.
SW OFF TIMES: Number of times that  switch on  the TV by the R/C.
WORKING HOURS: Number of hours that is working the TV.
FAC. DATE DDMY:  TV manufacture date (day, month, year).

Press END button to return to the previous menu.

KEYS Menu
Control menu of good operation of the top panel control keys. 
If, when a key of the panel is pressed, the value who appears is within the parameters that appear in this menu, the  
operation of this key is correct. High values near FF means, no key pressed.

Press END button to return to the previous menu.

GA6  VX.XX  ExpX
PxW Exp X.X LCD VXX

To activate or to deactivate the HOTEL MODE.

POWER ON FIXED: Disable power on/off button of remote control. 
MAX VOLUME : 

To limit the maximum volume.

Fix volume level.

VOL. FIX. VALUE:  Value of “VOLUME FIXED”
RC BUTTON: 

To activate or to deactivate all remote control keys.

PANEL BUTTON:  Disable all buttons on the main unit.
MENU KEYS: 

Disable “MENU” button on main unit and remote control.

OSD:   Disable the OSD displaying.
IN. MODE START:  Specify starting channel when power button is switched.
IN. MODE FIXED:  Allows start with the input specifi ed in “INPUT MODE START” and prohibit to change channel
 

  and 

input.

GA6  VX.XX  ExpX
PxW Exp X.X LCD VXX

Only information about VPS. Changes are not allowed.

VPS  Menu
Broadcasting code identifi cation.

In this menu the Hotel Mode is activated or deactivated.

Confi rm the selection with 

Use the up / down arrows to change between 
ON/OFF.

Press END button to return to the previous menu.

GA6  VX.XX  ExpX
PxW Exp X.X LCD VXX

Before to carry out the HD Component  White Balance  Adjustments, it is  requested to achieve  the Common bias and 
ADC adjustments in this order.

Input Component signal format 720p / 50Hz (Pattern: White 20%.)
Change to EXT 4 in menu TV and set brightness and contrast to 50%.
Enter in adjustment process by remote control (           key). The following OSD appears:

By up or down key choose Gamma R Lo or Gamma B Lo and adjust in order to become the reference value. Repeat as 
far as reference level is required.Don’t change green colour. It must be as default value.

Change pattern: White 80%.
By up or down key choose Gamma R Hi or Gamma B Hi and adjust in order to become the reference value. Repeat as 
far as reference level is required.Don’t change green colour. It must be as default value.

(For White Balance adjust it is recomended to use GAMMA CONST menu)
 
Before to carry out the  PC White Balance  Adjustments, it is  requested to achieve  the Common bias and ADC adjust-
ments in this order.

Input PC signal format -XGA (Pattern: White 20%.)
Change to PC Input in menu TV and set brightness and contrast to 50%.
Enter in adjustment process by remote control (browse key). The same White Balance Component HD OSD appears.

By up or down key choose Gamma R Lo or Gamma B Lo and adjust in order to become the reference value. Repeat as 
far as reference level is required.Don’t change green colour. It must be as default value.

Change pattern: White 80%.
By up or down key choose Gamma R Hi or Gamma B Hi and adjust in order to become the reference value. Repeat as 
far as reference level is required.Don’t change green colour. It must be as default value.

                      This Key (BROWSE) can be found in many  CRT TV
                      Remote Control. We detail two of them below:

   Part Reference             SN Price Code     EX Price Code

RRMCG0739BMSA 

    AW   

        BT 

RRMCG1022BMSA 

      **     

        BB