Sharp LC-24LS240EXK (serv.man2) Service Manual ▷ View online
53
LC-24LS240
1.6. USB Operations
USB operations can not be used directly. It can be used for updating panel tool, hw confi guration,
etc.
USB operations can not be used directly. It can be used for updating panel tool, hw confi guration,
etc.
1.5. Source Settings
54
LC-24LS240
SOFTWARE UPDATE
In MB62 project there is only one software. From following steps software update procedure can be
seen:
seen:
1. MB62 en. bin, mboot.bin and usb_auto_update_mb62.txt documents should copy directly inside
of fl ash memory ( not in a folder).
2. Put fl ash memory to the TV when TV is powered off.
3. Power on the TV by main switch and press OK in remote control continuously during 3 -4 sec-
3. Power on the TV by main switch and press OK in remote control continuously during 3 -4 sec-
onds. Then led will start blinking (red / green) quickly.
4. If First Time installation screen comes, it means software update procedure is successful.
55
LC-24LS240
2S&EGOPMKLX4VSFPIQ
4VSFPIQ-J8:MW[SVOMRKPIHMWRSVQEPERHXLIVIMWRSTMGXYVIERHFEGOPMKLXSRXLITERIP
4SWWMFPIGSYWIW&EGOPMKLXTMRHMQQMRKTMRFEGOPMKLXWYTTP]WXF]SRSJJTMR
&EGOPMKLXTMRWLSYPHFILMKLMRSTIRTSWMXMSR-JMXMWPS[TPIEWIGLIGO5ERHTERIP
GEFPIW
GEFPIW
(MQQMRKTMRWLSYPHFILMKLSVWUYEVI[EZIMRSTIRTSWMXMSR-JMXMWPS[TPIEWIGLIGO
7JSV1WXEVWMHIERHTERIPSVTS[IVGEFPIWGSRRIGXSVW
7JSV1WXEVWMHIERHTERIPSVTS[IVGEFPIWGSRRIGXSVW
&EGOPMKLXTS[IVWYTTP]WLSYPHFIMRTERIPWTIGW4PIEWIGLIGO'2JSV1&VIPEXIH
GSRRIGXSVWJSVTS[IVWYTTP]GEVHW
GSRRIGXSVWJSVTS[IVWYTTP]GEVHW
TROUBLESHOOTING
1. No Backlight Problem
Possible causes: Backlight pin, dimming pin, backlight supply, stby on/off pin.
56
LC-24LS240
78&=C323**WLSYPHFIPS[JSVWXERHF]SRGSRHMXMSRTPIEWIGLIGO6
'-1SHYPI4VSFPIQ
4VSFPIQ'-MWRSX[SVOMRK[LIR'-QSHYPIMRWIVXIH
4SWWMFPIGSYWIW7YTTP]WYTP]GSRXVSPTMRHIXIGXTMRWQIGLERMGEPTSWMXMSRWSJTMRW
'-WYTTP]WLSYPFI:[LIR'-QSHYPIMRWIVXIH-JMXMWRSX:TPIEWIGLIGO
'-C43;)6C'860XLMWTMRWLSYPHFIPS[
'-WYTTP]WLSYPFI:[LIR'-QSHYPIMRWIVXIH-JMXMWRSX:TPIEWIGLIGO
'-C43;)6C'860XLMWTMRWLSYPHFIPS[
2. CI Module Problem
Problem: CI is not working when CI module inserted.
Possible causes: Supply, supply control pin, detect pins, mechanical positions of pins
CI supply should be 5V when CI module inserted. If it not 5V please check
CI_POWER_CTRL, this pin should be low.
Problem: CI is not working when CI module inserted.
Possible causes: Supply, supply control pin, detect pins, mechanical positions of pins
CI supply should be 5V when CI module inserted. If it not 5V please check
CI_POWER_CTRL, this pin should be low.
Click on the first or last page to see other LC-24LS240EXK (serv.man2) service manuals if exist.