DOWNLOAD Sharp LC-24LS240EXK (serv.man2) Service Manual ↓ Size: 19.36 MB | Pages: 84 in PDF or view online for FREE

For displaying your computer’s screen image on your 
LCD TV, you can connect your computer to the TV set. 
Power off both computer and display before making 
any connections. Use 15-pin D-sub display cable to 
connect a PC to the LCD TV. When the connection 
is made, switch to PC source. See “Input selection” 
section. Set the resolution that suits your viewing 
requirements. Resolution information can be found 
in the appendix parts

.

You can connect a range of optional equipment to your 
LCD TV using side connectors of the TV.

For connecting a camcorder or camera , you should 

•

use AV socket (side). To do this, you must use the 
supplied video/audio connection cable. First, plug 
single jack of the cable to the TV’s AV IN socket 
(side). Afterwards, insert your camera cable’s (not
supplied) connectors into the plural part of the video/
audio connection cable. Colours of the connected 
jacks should match. See illustration below. 
Afterwards, you should switch to 

•

Side AV source. See 

the section Input selection in the following sections 
for more information.

To listen the TV sound from headphones, you 

•

should connect headphones to your TV by using the 
HEADPHONE jack as illustrated above..

Remove the battery cover located on the back of 

•

the handset by gently pulling backwards from the 
indicated part.
Insert two 

•

AAA/R3 or equivalent type batteries 

inside. Observe the correct polarity (+/-) when 
inserting batteries and replace the battery cover.

Connect the power cord to the 220-240V AC 50 Hz.

Switch the “

•

” button on the bottom right hand 

side under the screen to

 position “|” so the TV will 

switch to standby mode. Then the standby LED 
lights up.
To switch on the TV from standby mode either:

•

Press the “

•

” button, 

CH  / CH

 or a numeric 

button on the remote control.

Press the “

•

” or +/- button on the TV.

The TV will then switch on.

•
Note: If you switch on your TV via 

CH  / CH

on the remote control or on the TV set, the programme 
that you were watching last will be reselected. 
By either method the TV will switch on. 

To switch the TV to low power stand by press the 
“

” button on the remote control or right hand side 

of the TV.
Note: When the TV is switched to standby mode, 
standby LED can blink to indicate that features such 
as Standby Search, Over Air Download or Timer is 
active.

•

Switch the “

” button on the bottom right hand 

side under the screen to position 2 as illustrated, 

 to isolate the TV from the mains, the LED will 

go out.

A01_MB62_[GB]_1910UK_IDTV_TC_PVR_BRONZE19_24942LED_ROCKER_ZIGGO_10077476_50211339.indd 13

15.03.2012 16:27:18

A01_MB62_[GB]_1910UK_IDTV_TC_PVR_BRONZE19_24942LED_ROCKER_ZIGGO_10077476_50211339.indd 39

15.03.2012 16:27:33

1& QEMRFSEVH MW HVMZIR F] 17XEV 73' 8LMW -' MW GETEFPI SJ LERHPMRK :MHIS ERH
EYHMS TVSGIWWMRK 7GEPMRK(MWTPE] TVSGIWWMRK ( GSQFJMPXIV 37( ERH XI\X TVSGIWWMRK
0:(7 XVERWQMXXMRK GLERRIP ERH 14)+ HIGSHMRK MRXIKVEXIH (:&8' HIQSHYPEXSV
ERHQIHMEGIRXIVJYRGXMSREPMX]

8:WYTTSVXW 4%0 7)'%1 287'GSPSYVWXERHEVHW ERH QYPXMTPI XVERWQMWWMSR WXERHEVHW
EW&+(/--vERH00vMRGPYHMRK+IVQERERH2-'%1WXIVIS %PWS(:&8(:&'EVI
WYTTSVXIH MRXIVREP HIQSYPEXSVW SJ 1WXEV -' ERH (:&77 MW WYTTSVXIH [MXL I\XIVREPP
HIQSHYPEXSV

7SYRH W]WXIQ SYXTYX MW WYTTP]MRKQE\ \;  PIWW  8,( EX QE\ SYXTYX  [MXL 
WTIEOIVWSV\;JSVWXIVIS

7YTTSVXIHTIVMTLIVEPWEVI

6* MRTYX:,*-:,*---9,*$3LQ'SQQSR
7MHI%:':&760C%YHMS
7'%68WSGOIX'SQQSR
=4F4V3TXMSREP
4'MRTYX'SQQSR
,(1-MRTYX,(1-MRTYXMWGSQQSRMRTYXMWSTXMSREP
74(-*SYXTYX3TXMSREP
,IEHTLSRI3TXMSREP
'SQQSRMRXIVJEGI'SQQSR
97&'SQQSR
(:(3TXMSREP
3RFSEVH/I]TEH3TXMSREP
)\XIVREP/I]TEH3TXMSREP
)\XIVREP8SYGL4EH3TXMSREP