Sharp LC-24LE250EK (serv.man2) Service Manual ▷ View online
33
LC-24LE250 (C)
15
FDC642P
General Description and Features
TPS65251
a)
General Description
The TPS65251 features three synchronous wide input range high efficiency buck
converters. The converters are designed to simplify its application while giving the designer
the option to optimize their usage according to the target application.
The converters can operate in 5-, 9-, 12- or 15-V systems and have integrated power
transistors. The output voltage can be set externally using a resistor divider to any value
between 0.8 V and close to the input supply. Each converter features enable pin that allows a
delayed start-up for sequencing purposes, soft start pin that allows adjustable soft-start time
by choosing the soft-start capacitor, and a current limit (RLIMx) pin that enables designer to
adjust current limit by selecting an external resistor and optimize the choice of inductor. The
current mode control allows a simple RC compensation.
The switching frequency of the converters can either be set with an external resistor
connected to ROSC pin or can be synchronized to an external clock connected to SYNC pin if
needed. The switching regulators are designed to operate from 300 kHz to 2.2 MHz. 180° out
of phase operation between Buck 1 and Buck 2, 3 (Buck 2 and 3 run in phase) minimizes the
input filter requirements.
34
LC-24LE250 (C)
16
TPS65251 features a supervisor circuit that monitors each converter output. The PGOOD
pin is asserted once sequencing is done, all PG signals are reported and a selectable end of
reset time lapses. The polarity of the PGOOD signal is active high.
TPS65251 also features a light load pulse skipping mode (PSM) by allowing the LOW_P
pin tied to V3V. The PSM mode allows for a reduction on the input power supplied to the
system when the host processor is in stand-by (low activity) mode.
b)
Features
• Wide Input Supply Voltage Range (4.5 V - 18 V)
• 0.8 V, 1% Accuracy Reference
• Continuous Loading: 3 A (Buck 1), 2 A (Buck 2 and 3)
• Maximum Current: 3.5 A (Buck 1), 2.5 A (Buck 2 and 3)
• Adjustable Switching Frequency 300 kHz - 2.2 MHz Set By External Resistor
• Dedicated Enable for Each Buck
• External Synchronization Pin for Oscillator
• External Enable/Sequencing and Soft Start Pins
• Adjustable Current Limit Set By External Resistor
• Soft Start Pins
• Current-Mode Control With Simple Compensation Circuit
• Power Good
• Optional Low Power Mode Operation for Light Loads
• QFN Package, 40-Pin 6 mm x 6 mm RHA
APPLICATIONS
• Set Top Boxes
• Blu-ray DVD
• Security Camera
• Car Audio/Video
• DTV
• DVR
35
LC-24LE250 (C)
17
Table 5: Recommended operating conditions
Figure 7: Pin description
36
LC-24LE250 (C)
18
Table 6: Pin functions
MP1484
a)
General Description
The MP1484 is a monolithic synchronous buck regulator. The device integrates top and
bottom 85m
MOSFETS that provide 3A of continuous load current over a wide operating
input voltage of 4.75V to 18V. Current mode control provides fast transient response and
cycle-by-cycle current limit.
An adjustable soft-start prevents inrush current at turn-on and in shutdown mode, the
supply current drops below 1
A.
The MP1484 is PIN compatible to the MP1482 2A/18V/Synchronous Step-Down Converter.
b)
Features
• 3A Continuous Output Current
• Wide 4.75V to 18V Operating Input Range
• Integrated 85m
Power MOSFET Switches
Click on the first or last page to see other LC-24LE250EK (serv.man2) service manuals if exist.