Sharp LC-22LE240K Service Manual ▷ View online
21
LC-22LE240
---
Pinning Table
and Application Block Diagram of Tuner---
2. AUDIO AMPLIFIER STAGE WITH AZAD2102(U163, U164)
2.1. General Description
17MB62 uses two 2,5W Class D Mono Audio Amplifers for from 16” to 24” TVs.
AZAD2102B is a 2.9 Watts (max. can offer 3.0 Watts @ Load = 3Ω,THD=10%,
AVdd=DVdd=5.5Volt)with high efficiency filter-free class-D audio power amplifier in a
1613 mm x 1613 mm wafer chip scale package (WCSP). AZAD2102B uses Current-
switch technology to achieve high performance class-d amplifier that features 0.03%
THD, 85% efficiency, –70 dB PSRR, to improve RF-rectification immunity.
AZAD2102B provide a Vibration-Spectrum modulation clock for PWM Output. This
vibration frequency is around 10KHZ shift (+/- 5KHZ of Fpwm).
The advantage of the small size package (WCSP) makes AZAD2102B very suitable for
mobile phone and PDA device application. And the Class-D amplifier structure let
AZAD2102B to have highly efficiency power consumption than Class-AB amplifier.
AZAD2102B can shrink the application board, reduce system cost, and external
components.
ESD level protection I/O embedded in AZAD2102B. For general applications, doesn’t
need to add extra ESD protection device (like Varistors) in application system for
AZAD2102B’s I/O.
2.2. Features
CMOS Technology
High Efficiency 85%
High PSRR 70dB at 217Hz
Differential OP-amp Input
AZAD2102B provides Vibration-Spectrum Modulation clock for reduce EMI
Provide Mute function(set Mute_B to GND will go into Mute status)
For the input stage AZAD2102B built-in a 10Kohm resistors (Gain setting=29.5dB)
Maximum Battery Life and Minimum Heat
Efficiency With an 8-Ω Speaker:
3.5 mA Quiescent Current
Output Power at 10% THD
2.85Watts at AVdd=DVdd=5.0Volt, Rload=4Ω
1.45Watts at AVdd=DVdd=3.6Volt, Rload=4Ω
0.30Watts at AVdd=DVdd=3.0Volt, Rload=4Ω
1.75Watts at AVdd=DVdd=5.5Volt, Rload=8Ω
0.87Watts at AVdd=DVdd=3.6Volt, Rload=8Ω
0.41Watts at AVdd=DVdd=3.0Volt, Rload=8Ω
Eliminate Power on and Power-off “Pop” noise
A Fewer External Components
Optimized PWM Output Stage Eliminates LC Output Filter
Internally generate 290 kHz Switching Frequency to eliminate Capacitor and
Resistor
Improve PSRR (–70 dB) and Wide Supply Voltage (3.0 V to 5.5 V)
Fully Differential Design Reduces RF Rectification
This chip has been built-in a very strong ESD protection.
System level ESD 4KV (IEC 61000-4-2 ESD Contact Level)
Wafer Chip Scale Package (WCSP)
TSSOP Package with Exposed Pad
22
LC-22LE240
2.3. Absolute Ratings
2.3.1.
Electrical Characteristics
23
LC-22LE240
2.3.2.
Operating Specifications
2.4. Pinning
3. AUDIO AMPLIFIER STAGE WITH TPA3113(U168)
3.1. General Description
17MB62 uses a 6W Class D Mono Audio Amplifers for from 26” to 32” TVs. The
TPA3113D2 is a 6-W (per channel) efficient, Class-D audio power amplifier for driving
bridged-tied stereo speakers. Advanced EMI Suppression Technology enables the use of
inexpensive ferrite bead filters at the outputs while meeting EMC requirements.
SpeakerGuard™ speaker protection circuitry includes an adjustable power limiter and a
DC detection circuit. The adjustable power limiter allows the user to set a "virtual" voltage
rail lower than the chip supply to limit the amount of current through the speaker. The DC
detect circuit measures the frequency and amplitude of the PWM signal and shuts off the
output stage if the input capacitors are damaged or shorts exist on the inputs.
The TPA3113D2 can drive stereo speakers as low as 4 Ω. The high efficiency of the
TPA3113D2, 87%, eliminates the need for an external heat sink when
playing music.
The outputs are also fully protected against shorts to GND, VCC, and output-to-output.
The short-circuit protection and thermal protection includes an auto-recovery feature.
24
LC-22LE240
2.4. Pinning
3. AUDIO AMPLIFIER STAGE WITH TPA3113(U168)
3.1. General Description
17MB62 uses a 6W Class D Mono Audio Amplifers for from 26” to 32” TVs. The
TPA3113D2 is a 6-W (per channel) efficient, Class-D audio power amplifier for driving
bridged-tied stereo speakers. Advanced EMI Suppression Technology enables the use of
inexpensive ferrite bead filters at the outputs while meeting EMC requirements.
SpeakerGuard™ speaker protection circuitry includes an adjustable power limiter and a
DC detection circuit. The adjustable power limiter allows the user to set a "virtual" voltage
rail lower than the chip supply to limit the amount of current through the speaker. The DC
detect circuit measures the frequency and amplitude of the PWM signal and shuts off the
output stage if the input capacitors are damaged or shorts exist on the inputs.
The TPA3113D2 can drive stereo speakers as low as 4 Ω. The high efficiency of the
TPA3113D2, 87%, eliminates the need for an external heat sink when
playing music.
The outputs are also fully protected against shorts to GND, VCC, and output-to-output.
The short-circuit protection and thermal protection includes an auto-recovery feature.
3.2. Features
6-W/ch into an 8-Ω Loads at 10% THD+N From a 10-V Supply
12-W into a 4-Ω Mono Load at 10% THD+N From a 10-V Supply
87% Efficient Class-D Operation Eliminates Need for Heat Sinks
Wide Supply Voltage Range Allows Operation from 8 V to 26 V
Filter-Free Operation
SpeakerGuard™ Speaker Protection Includes Adjustable Power Limiter plus DC
Protection
Flow Through Pin Out Facilitates Easy Board Layout
Robust Pin-to-Pin Short Circuit Protection and Thermal Protection with Auto
Recovery Option
Excellent THD+N / Pop-Free Performance
Four Selectable, Fixed Gain Settings
Differential inputs
3.3. Absolute Ratings
3.3.1.
Electrical Characteristics
Click on the first or last page to see other LC-22LE240K service manuals if exist.