Sharp LC-20AD5E (serv.man2) User Manual / Operation Manual ▷ View online
GB
-3
Quick guide
Attaching the stand (LC-26AD5E, LC-26AD5S, LC-32AD5E, LC-32AD5S)
Before performing work spread cushioning over the base area to lay the TV on, making sure the area is
completely flat. This will prevent it from being damaged.
Before attaching (or detaching) stand, unplug the AC cord from the AC INPUT terminal.
Confirm the 8 screws supplied with the TV.
Short screws (
X
4)
(used in step 2)
Long screws (
X
4)
(used in step 3)
2
Remove the covering sheet before use.
Set the post for the stand unit onto the box.
2
Attach the base to the post.
3
Attach the base to the 4 screws into the 4 holes on
the bottom of the base.
NOTE
• To detach the stand, perform the step in reverse order.
Hex key
Screw
Soft cushion
3
Insert the stand into the openings on the bottom of
the TV.
2
Insert and tighten the 4 screws into the 4 holes on
the rear of the TV.
Setting the TV
Removing the covering sheet
For protection, sheets , and are covering the product. Please remove these sheets before use.
( : LC-20AD5E, LC-20AD5S Black models only / , : Black models only)
Remove each sheet.
Tear from the cut point and
remove the sheet by peeling it
back to either side.
There is a protective film
covering the face of the
remote control. Please
remove this film before
use.
Hex key
Screw
GB
-4
Quick guide
Place the TV close to the AC
outlet, and keep the power
plug within reach.
Standard DIN45325 plug
(IEC 169-2)
75-ohm coaxial cable
(For Europe,
except U.K.
and Eire)
AC cord
Antenna
Connect the antenna cable
from your antenna-/cable
socket or the (room-/roof)
antenna for antenna input
terminal on the back of your
TV set to receive digitally/
terrestrially broadcast
stations.
An indoor antenna can also
be used under good reception
conditions.
Bundling the cables
Cable clamp
LC-26AD5E, LC-26AD5S
LC-32AD5E, LC-32AD5S
LC-20AD5E, LC-20AD5S
LC-20AD5E, LC-20AD5S
LC-26AD5E, LC-26AD5S
LC-32AD5E, LC-32AD5S
Removing the terminal cover
Pull down the hooks to open the cover.
LC-20AD5E, LC-20AD5S
LC-26AD5E, LC-26AD5S
LC-32AD5E, LC-32AD5S
Cable clamp
This cable clamp is already
attached to the housing of the
LC-20AD5E and LC-20AD5S
models.
(For U.K.
and Eire)
Setting the TV on the wall
This TV should be mounted on the wall only with the wall mount bracket available from SHARP. (See page 33.)
The use of other wall mount brackets may result in an unstable installation and may cause serious injuries.
When you use the AN-26AG (SHARP) for LC-26AD5E/LC-26AD5S or AN-37AG2 (SHARP) for LC-32AD5E/LC-
32AD5S wall mount bracket, set the angle of the TV up to 20°.
Installing the LCD Colour TV requires special skill that should only be performed by qualified service personnel.
Customers should not attempt to do the work themselves. SHARP bears no responsibility for improper mounting
or mounting that results in accident or injury.
You can ask a qualified service p ersonnel about using an optional bracket to mount the TV to the wall.
•
•
•
•
GB
-5
Quick guide
Inserting the batteries
Before using the TV for the first time, insert two “AA” size batteries (supplied). When the batteries become
depleted and the remote control unit fails to operate, replace the batteries with new “AA” size batteries.
Open the battery cover.
2
Insert two supplied “AA” size
batteries.
3
Close the battery cover.
Place batteries with their terminals
corresponding to the (+) and (−) indications
in the battery compartment.
•
CAUTION
Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.
Do not mix batteries of different types. Different types of batteries have different characteristics.
Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause chemical
leakage in old batteries.
Remove batteries as soon as they have worn out. Chemicals that leak from batteries can cause a rash. If you find any
chemical leakage, wipe thoroughly with a cloth.
The batteries supplied with this product may have a shorter life expectancy due to storage conditions.
If you will not be using the remote control unit for an extended period of time, remove the batteries from it.
Using the remote control unit
Use the remote control unit by pointing it towards the remote control sensor. Objects between the remote
control unit and sensor may prevent proper operation.
•
•
•
•
•
30
o
5m
30
o
Remote control sensor
Cautions regarding the remote control unit
Do not expose the remote control unit to shock.
In addition, do not expose the remote control unit to liquids, and do not place
in an area with high humidity.
Do not install or place the remote control unit under direct sunlight. The heat
may cause deformation of the unit.
The remote control unit may not work properly if the remote control sensor of
the TV is under direct sunlight or strong lighting. In such case, change the
angle of the lighting or TV, or operate the remote control unit closer to the
remote control sensor.
•
•
•
GB
-6
Quick guide
Remote control unit
4
2
3
6
7
8
8
6
7
7
8
9
3
20
2
22
23
23
24
9
0
25
2
4
5
5
(Standby/On)
Enter standby mode or turn on the
power. (See page 8.)
2
DTV/RADIO*
DTV: Switch between RADIO and
DTV mode.
3
DTV/TV
Switch between analogue TV and
DTV mode.
4
(Mute)
Switch the sound on and off.
5
0–9
Set the channel in TV and DTV mode.
Set the page in Teletext mode.
6
(Flashback)
Press to return to the previous image
in normal viewing mode.
7
(WIDE MODE)
Select the wide mode.
(See page 18.)
8
(Sound mode)
Select the sound multiplex mode.
(See below.)
9
EPG
DTV: To display EPG (Electronic
Programme Guide) screen.
0
(Teletext)
Displays the Teletext mode screen.
(See page 19.)
DTV: Select DTV data broadcasting
and TELETEXT.
END
Exit the menu screen.
2
(Reveal hidden Teletext)
TELETEXT: (See page 19.)
3
(Freeze/Hold)
TV/DTV: You can freeze a motion
picture on the screen.
TELETEXT: (See page 19.)
4
(+/−) (Volume)
(+) Increase the volume.
(−) Decrease the volume
* If “Sweden” was selected on the
“First installation (Country)” screen,
you can switch between RADIO,
DATA and DTV modes.
5 P ( / )
TV/DTV: Select the channel.
External: Switch to TV or DTV input
mode.
Teletext: Move to the next/previous
page.
6
(INPUT SOURCE)
Select an input source.
(See page 9.)
7 SLEEP
Set the sleep timer in units of 30 min.
up to max. 2 hr.
8
(Display information)
Display various information; channel
number, sleep timer, etc.
(See pages 27 and 28.)
9 DTV MENU
DTV: Display DTV Menu screen.
20 MENU
Display the MENU screen.
(See page 11.)
2 ▲/▼/◀/▶ (Cursor)
Select a desired item on the setting
screen.
OK
Execute a command within the menu
screen.
DTV: Display the Channel list.
22
(Top/Bottom/Full)
Set the area of magnification in
Teletext mode. (See page 19.)
23
(Subpage)
(See page 19.)
24
(Subtitle for Teletext)
TELETEXT: To turn the subtitles on
and off. (See page 19.)
DTV: Display the subtitle selection
screen. (See page 29.)
25 Colour (Red/Green/Yellow/Blue)
TELETEXT: Select a page.
(See page 19.)
DTV: The coloured buttons are used
to select correspondingly to the
coloured items in the menu screen.
●
Using
on the remote control unit
DTV mode:
Press
to open the multi audio screen. (See page 29.)
Analogue TV mode:
Each time you press
, the mode switches as illustrated
in the following tables.
Broadcast
Stereo
Bilingual
Monaural
NICAM
Mono
Stereo
Sound 2
Sound 1+2
Mono
Sound 1
Mono
Nicam
A2 Stereo
Mono
Stereo
Sound 2
Sound 1+2
Mono
Sound 1
Mono
NOTE
When no signal is input, the sound mode will display “Mono”.
•
Click on the first or last page to see other LC-20AD5E (serv.man2) service manuals if exist.