Sharp LC-20AD5E (serv.man2) User Manual / Operation Manual ▷ View online
GB
-23
Installation
This section describes how to reconfigure the DTV
settings after conducting Initial auto installation on
page 8.
Auto Scan
The TV automatically detects and stores all available
services in your area.
Press ◀/▶ to select “Installation”.
2
Press ▲/▼ to select “Auto Scan”, and then press
OK.
A confirmation message displays.
•
3
Press ◀/▶ to select “Yes”, and then press OK.
The TV starts scanning all available DTV and radio
services in your area.
•
NOTE
To cancel the scan in progress, press END.
Manual Scan
Manually add a new carrier by entering the desired
carrier number or frequency band.
Press ◀/▶ to select “Installation”.
2
Press ▲/▼ to select “Manual Scan”, and then
press OK.
Manual Scan
Channel list
Ch-5
Frequency (kHz)
177500
0..9
Navigate
OK
END
3
Press ▲/▼ to select “Channel list”, then ◀/▶ to
enter the carrier number, and then press OK.
The frequency of the selected carrier in the below
cell changes correspondingly.
•
4
After the scan is complete, the screen shows all
available services for the selected range.
A confirmation message displays.
•
5
Press ◀/▶ to select “Yes”, and then press OK.
NOTE
If “Sweden” is selected on the “First installation
(Country)” screen, the “Frequency (kHz)” cannot be
used.
When the Country is set to Sweden in the “First
installation (Country)”
When there is a Channel List in the data after Auto
Scan or Manual Scan, Channel Type Selection Menu
will be displayed and available to set Channel List
Type.
Select the Channel List Type by pressing
◀/▶ and
press OK.
•
•
Move
Sort the order of the selected service by moving the
service position.
Press ▲/▼ to select the desired service.
2
Press 7 on the remote control. An icon displays
indicating the service to be moved.
Pressing
7 will turn the move icon on and off.
•
3
Move the selected service to the desired position
using ▲/▼, and then press OK to register the
change.
Move To
Sort the order of the selected service by modifying
the service number.
Press ▲/▼ to select the desired service.
2
Press 8 on the remote control. Now you can
change the service number on the left side of the
screen.
3
Enter the number using 0 - 9 numeric buttons,
and then press OK. The service moves to the
new position.
NOTE
If on the “First installation (Country)” screen “UK” is
selected, “Move To” cannot be used in U.K.
View
Change to the service shown in the picture window.
Press ▲/▼ to select the desired service.
2
Press OK on the remote control.
The image shown in the picture window changes.
•
3
Press END to exit the Channel Organizer screen
to view the image in full screen.
•
DTV menu operations
GB
-24
System Configuration
Configure On-Screen Display and Child Lock
settings.
Display Setup
The On-Screen Display appearance and the position/
duration of the service banner information can be
customised.
Press ◀/▶ to select “System Configuration”.
2
Press ▲/▼ to select “Display Setup”, and then
press OK.
Display Setup
END
Navigate
OK
Banner timeout
4 Secs
Banner position
Bottom
Display Transparency
10%
3
Press ▲/▼ to select the desired item.
4
Press ◀/▶ to select the desired parameter, and
then press END.
OSD Setup
items
Selectable items
Description
Banner
timeout
Sec/2 Secs/
... 7 Secs
Select how long the service
banner information appears
on screen.
Banner
position
Top/Bottom
Select whether the service
banner information appears
on top or bottom of the
screen.
Display
Transparency
None/0%/20%/
...50%
Select the desired level
of On-Screen Display
transparency.
DTV menu operations
Carrier Setup
This is provided for you to rename (label), delete,
or re-scan carriers. “Carrier” in this context refers
to a service station that provides a set of individual
services.
Press ◀/▶ to select “Installation”.
2
Press ▲/▼ to select “Carrier Setup”, and then
press OK.
001 DVB-T 16QAM
184500
03 01
002 DVB-T 16QAM
506000
03 01
003 DVB-T 64QAM
842000
05 00
FEC :7/8
FFT : 2k Frequency (kHz): 506000
QAM :16
GI : 1/32
S.No Carrier Name
Frequency TV Radio
Carrier Setup
END
Navigate
OK
Rename
Delete
Rescan
①
To rename the selected carrier:
Select the carrier, and then press RED (Rename).
The character set screen displays.
Enter a new name for the carrier. See page 21 for
details on using the character set screen.
Press OK.
A confirmation message displays.
Press
◀/▶ to select “Yes”, and then press OK.
②
To delete the selected carrier:
Select the carrier, and then press GREEN
(Delete).
An icon displays indicating the carrier to be
deleted.
Pressing GREEN will turn the delete icon on and
off.
Press OK.
A confirmation message displays.
Press
◀/▶ to select “Yes”, and then press OK.
③
To re-scan the selected carrier:
Select the carrier, and then press BLUE (Rescan).
Re-scanning starts.
A confirmation message displays.
Press
◀/▶ to select “Yes”, and then press OK.
NOTE
If “Sweden” is selected on the “First installation
(Country)” screen, DATA is displayed on the “Carrier
Setup” screen.
•
GB
-25
Password Setup (Parental Lock)
This function allows TV and Radio services to be
restricted. It prevents children from watching violent
or sexual scenes that may be harmful.
Press ◀/▶ to select “System Configuration”.
2
Press ▲/▼ to select “Password Setup”, and then
press OK.
3
If you already set the PIN, enter it here. If not,
enter the factory preset PIN “0000”.
4
Press ▲/▼ to select “Parental Lock”.
5
Press ◀/▶ to select the desired age/rating
(4 ...18/None).
Password Setup
END
Navigate
OK
Parental Lock
None
Change password
- - - -
6
Press ▲/▼ to select “Change password”.
7
Enter the 4-digit number as a PIN using 0 – 9.
8
Enter the same 4-digit number as in step 7 to
confirm.
“Successfully updated” displays.
•
9
Press END.
NOTE
To view a locked channel, you must enter a PIN. When
you select a locked channel, a PIN prompt message
pops up. Enter the 4 digit number using 0–9.
As a precautionary measure, make a note of your PIN
on the back of this operation manual, cut it out and
keep it in a safe place that children cannot reach.
See page 34 for resetting the current PIN to the
factory preset “0000” if you lose or forget your PIN.
Technical Information
Check the version information of the digital module
and allow it to be upgraded (when available).
Version
Check the version information of the digital module.
Press ◀/▶ to select “Technical Information”.
2
Press ▲/▼ to select “Version”, and then press
OK.
The hardware and software versions are displayed.
•
•
•
•
DTV menu operations
Software upgrade
The software for controlling the built-in DTV decoder
can be upgraded when necessary. In Great Britain
this can be achieved via an Over Air Download.
Preparation
Preparation
Confirm and make a note of the current software
version number as in step 2 of Software Version.
Manual upgrade
Manual upgrade
Press ◀/▶ to select “Technical Information”.
2
Press ▲/▼ to select “Software upgrade”, and
then press OK. The TV checks all carriers if there
is a new software available for upgrade.
①
If upgrade via Over Air Download is available at
the time:
A confirmation message appears asking you to
accept the upgrade or not.
To download now, press
◀/▶ to select “Yes”, and
then press OK. After the upgrade is completed,
the TV restarts automatically with the new software
version installed.
To postpone the download, press
◀/▶ to select
“No”, and then press OK. Enter the download time
for more convenient time as instructed.
The software upgrade will not be carried out if
there is no new software available at the specified
download time.
②
If upgrade via Over Air Download is NOT
available at the time:
A message tells you that there is no software
available to be downloaded.
3
Check the new software version number to
confirm the successful upgrade.
Auto upgrade
When you tune to the service that provides the
upgrade via Over Air Download, a confirmation
message displays.
2
Follow the screen prompts.
3
Check the new software version number to
confirm the successful upgrade.
NOTE
To scan all carriers for upgrade availability, perform the
manual upgrade.
The software upgrade may take about 30 minutes, but
may take longer (up to 1 hour) depending on the signal
status. While updating, you can switch to TV or external
input mode or enter standby mode using on the
remote control unit.
CAUTION
Do not disconnect the AC cord when the software
upgrade is in progress, as this may cause the
upgrade to fail. If problem arises ask a qualified
service personnel before the software upgrade
period expires.
•
•
•
GB
-26
DTV menu operations
NOTE
To view paid TV broadcasting, you need to make a
contract with a service provider.
Please contact a service provider for details.
The Common Interface Module and the CA card are
neither supplied nor optional accessories.
Leaving your CA card inserted does not affect free to
view channels.
About The Common Interface Slot
(LC-20AD5E, LC-20AD5S only)
At the time of purchase a dummy CI card is already
loaded into the Common Interface slot. When you
are ready to load your CI card, press the button
indicated by the arrow and remove the dummy CI
card. When you remove your CI card, replace it with
the dummy CI card to prevent dust or other material
from getting into the Common Interface slot.
•
•
•
Dummy CI card
Push to eject
Common Interface
Check the detailed information on the Common
Interface module card in use.
Press OK while the cursor is on “Common
Interface”.
The CI module name is displayed.
•
Cl Module
Module Name
Top Up TV
END
OK
2
Press OK to access the CI menu.
Detailed information on the CI card in use is
displayed.
•
3
Press ▲/▼ to select the item, and then press OK.
Detailed information on the selected item is
displayed.
•
Inserting a CA card
A single DVB Common Interface (CI) slot is provided
to allow adoption of a Conditional Access (CA)
system by means of a plug-in CA module.
Scrambled Broadcasting service can be routed via
the CA system.
To allow the use of smart-card type CA system, a
Conditional Access Module (CAM) is required. This
should be obtained along with the CA card at the
time of purchase. Please follow the service provider’s
instructions to activate the card.
When the compatible card is not inserted:
①
Select the programme which needs the compatible
CA card.
The caution screen appears.
•
②
Insert the compatible CA card.
The caution screen disappears and you can view
the programme.
•
CA system supported by
Crypto Works
Crypto Works
Aston CAM
VIAccess
Nagra Vision
Irdeto
MR CAM
Conditional Access Module
CA card
C.I. Slot
Click on the first or last page to see other LC-20AD5E (serv.man2) service manuals if exist.