DOWNLOAD Sharp LC-19D1EWH (serv.man10) Service Manual ↓ Size: 1.2 MB | Pages: 32 in PDF or view online for FREE

●

Provide high quality images with minimal dot crawl and
cross colour noise by detecting changes in the image.

Standard: Normal adjustment
Fast: Set the optimum image quality for fast-moving

images.

Slow: Set the optimum image quality for slow-moving

images.

Off: No detecting

• 3D-Y/C may not operate depending on the input signal

type or noisy input signal.

• This function is only available when a CVBS signal is input.

(Except a SECAM CVBS signal.)

●

For viewing a video in monochrome.

• When Monochrome is set to “On”, the DTV Menu screen

displays in monochrome.

●

Automatically detect a film-based source (originally
encoded at 24/25 frames/second, depending on the
vertical frequency), analyses it then recreates each
still film frame for high-definition picture quality.

Menu Operation: B (page 9)
You can adjust the sound quality of each AV MODE to
your preference with the following settings
(DYNAMIC(FIXED) cannot be adjusted).

Audio

Treble

Bass

Balance

Sound Wide

Reset

[ + 2]

[    0]

[ + 3]

DYNAMIC

–

L

–

+

+

R

Menu Operation: A (page 9)
This feature can increase the spread of the sound.

●

Adjust the colour temperature to give the best white
image.

High: White with bluish tone
Mid-High: Intermediate tone between High and Middle
Middle: Natural tone
Mid-Low: Intermediate tone between Middle and Low
Low: White with reddish tone

C. M. S.-Hue: This is a standard to adjust the colour

either more reddish or more bluish in tone.

C. M. S.-Saturation: Increases or decreases the saturation

of a selected colour.

C. M. S.-Value: A higher value makes the image brighter.

A lower value makes the image darker.

On: Increases the spread of the sound.
Off: Outputs the normal sound.

●

Colour tone is managed using the six-colour
adjustment setting.

●

Adjust the image and input signal can give you a more
beautiful picture.

Interlace: Display finely detailed images for TV or video,

etc.

Progressive: Display smooth images for still images or

graphics, etc.

• This function is not available when using headphones.

c button

d button

For weaker treble

For stronger treble

For weaker bass

For stronger bass

Decrease audio
from the right
speaker

Decrease audio
from the left
speaker

You can run Auto Installation again, even after setting
up the preset channels.

Press MENU and the MENU screen displays.

Press c/d to select “Setup”.

Press a/b to select “Auto Installation”, and then
press OK.
If you have already set the PIN under “Child Lock”,
enter it here.

• See page 14 for setting PIN.

Press a/b to select “Yes”, and then press OK.

You can set language and country the same as in
the  Initial auto installation (Analogue). (See
page 7.)

This section describes how to set up analogue TV
channels manually.

Press MENU and the MENU screen displays.

Press c/d to select “Setup”.

Press  a/b to select “Programme Setup”, and
then press OK.
If you have already set the PIN under “Child Lock”,
enter it here.

• See page 14 for setting PIN.

Press a/b to select “Auto Search”, “Manual Adjust”,
“Sort” or “Erase Programme”, and then press OK.

Setup

Input Label

Auto Installation

Programme Setup

Child Lock

Position

PC Setup

HDMI Audio Select

HDMI Auto View

WSS

4:3 Mode

Rotate

Lanugage

Supply Voltage

Reset

Auto Search

Manual Adjust

Sort

Erase Programme

No

Yes

When set to “Enable” the TV will automatically enter
the standby mode if there is no signal input for 15
minutes.

• Five minutes before the TV enters standby mode, the

remaining time displays every minute.

• When a TV programme finishes, this function may not

operate.

• This function is not available in DTV mode.

Power Control

No Signal Off

No Operation Off

Power Management

Menu Operation: A (page 9)
When you select the desired time, the TV will
automatically enter the standby mode if no operation
is performed.

When set, the TV will automatically enter the standby
mode.

• No power management

Mode1: • If there is no signal input for 8 minutes, the TV

enters the standby mode.

• Even if you start using the PC and the signal

inputs again, the TV stays in standby mode.

• The TV turns on again by pressing a on the TV

or B on the remote control unit. (See page 7.)

Mode2: • If there is no signal input for 8 seconds, the

TV enters the standby mode.

• When you start using the PC and the signal

inputs again, the TV turns on automatically.

• The TV turns on again by pressing a on the TV

or B on the remote control unit. (See page 7.)

• Five minutes before the TV enters standby mode, the

remaining time displays every minute.

30 min. / 3hr. / Disable

• When selecting “Reset” in the Setup menu, all menus will be reset

to the factory preset values and “Auto Installation” will activate.

●

You can set some channel items manually.

Press MENU and the MENU screen displays.

Press c/d to select “Setup”.

Press  a/b to select “Programme Setup”, and
then press OK.
If you have already set the PIN under “Child Lock”,
enter it here.

• See page 14 for setting PIN.

Press  a/b to select “Manual Adjust” and then
press OK.

Press a/b to select “Yes”, and then press OK.

Press a/b/c/d to select the channel you want
to edit, and then press OK.

• The selected channel information displays.

Press a/b to select the desired menu item, and
then press OK.

Press a/b (/0–9/c/d) to select or adjust.

Colour Sys.

Sound Sys.

Label

Skip

Decoder

Lock

179.25

MHz

Fine

You can adjust the frequency to your desired position.

When a TV channel sends its Network Name, the Auto
Installation detects the information and assigns a name
to it. However, you can change individual channel
names.

Repeat steps 1 to 7 in Manual Adjust.

Channels with “Skip” set to “On” are passed over when
using  Pr/Ps even if selected while watching the
image from the TV.

When connecting a decoder to the unit, you need to
select EXT 1.

You can block the viewing of any channel.

• See page 14 for setting PIN.
• When Lock is set to “On” for a channel, “Child lock has

been activated.” displays, and the image and sound of
the channel are blocked.

• When pressing OK while “Child lock has been activated.”

displays, PIN input menu will display. Inputting the correct
PIN lifts the child lock temporarily until the power is turned
off.

Select the optimum colour systems to receive. (AUTO,
PAL, SECAM)

• If “Auto” is selected, colour system for each channel is

automatically set. If an image does not display clearly,
select another colour system (e.g. PAL, SECAM).

Select the optimum sound systems (Broadcasting
systems) to receive. (B/G, D/K, I, L, L’)

Press a/b to select characters and c/d to move
to the desired digit.

Repeat step 2 above until the name is fully spelt
out, and then press OK to complete the label
setting.

●

You can automatically search for and download TV
channels  by performing the procedure below. This is
the same function as from programme auto search to
auto sorting in Auto Installation.

Repeat steps 1 to 4 in Programme Setup.

Press a/b to select “Yes”, and then press OK.

• Adjust while checking the background picture as a

reference.

• Instead of pressing c/d to adjust the frequency in step

8 above, you can set by directly entering the frequency
number of the channel with 0–9.

• 179.25 MHz: Press 1 s 7 s 9 s 2 s 5.
• 49.25 MHz: Press 0 s 4 s 9 s 2 s 5.

Allows you to use a PIN to protect certain settings from
being accidentally changed.

Press MENU and the MENU screen displays.

Press c/d to select “Setup”.

Press a/b to select “Child Lock”, and then press
OK. If you have already set the PIN under “Child
Lock”, enter it here.

New PIN

–

–

–

Reconfirm

–

–

–

–

–

Change PIN

Reset

You can assign each input source a label you like.

Press b to select the desired input source.

Press MENU and the MENU screen displays.

Press c/d to select “Setup”.

Press a/b to select “Input Label”, and then press
OK.

Press a/b to select characters and c/d to move
to the desired digit to label the input source.

• When you want to change the input label to the

default name, select “CLEAR” on the “Input Label”
screen.

Repeat step 5 above until the name is fully spelt
out, and then press OK.

• The name can be 6 characters or less.
• When you want to set an input source name of less

than 6 characters, press MENU to exit from the
labelling menu.

• You cannot change the label if the input source is TV or

DTV.

●

An individual programme can be erased.

Repeat steps 1 to 4 in Programme Setup.

Press a/b to select “Yes”, and then press OK.

Press a/b/c/d to select the channel you want
to erase, and then press OK.

Press OK to erase the selected programme. All
the subsequent programmes move up.

Repeat steps 3 and 4 until all desired channels
are erased.

●

Channel positions can be sorted freely.

Repeat steps 1 to 4 in Programme Setup.

Press a/b to select “Yes”, and then press OK.

Press a/b/c/d to select the channel you want
to move, and then press OK.

Press  a/b/c/d to move it to the desired
position, and then press OK.

Repeat steps 3 and 4 until all desired channels
are sorted.

Allows you to reset your PIN to the factory preset
“1234”.

Repeat steps 1 to 3 in Changing the PIN.

Press a/b to select “Reset”, and then press OK.

Press a/b to select “Yes”, and then press OK.

• As a precautionary measure, make a note of your PIN

• See page 25 for resetting the current PIN to the factory

• To relock a channel which has been temporarily

Press a/b to select “Change PIN”, and enter the
4-digit number as a PIN using 0–9.

Enter the same 4-digit number as in step 4 to
confirm.

• When setting the PIN, “Reset” in the Menu will be

selectable and operational.

• To view a locked channel (Lock setting in Programme

Setup “Manual Adjust” is set to “On”), you must enter a
PIN. (See page 13 and page 19 for locking channels from
viewing in analogue TV and DTV mode.) When you select
a locked channel, a PIN prompt message pops up. Press
OK to display the PIN input window.

For adjusting a picture’s horizontal and vertical
position.

• Adjustments are stored separately according to input

• Depending on the input signal type a position setting may

not be available.

H-Pos.: Centres the image by moving it to the left or right.
V-Pos.: Centres the image by moving it up or down.