Sharp 21LF-90H (serv.man3) Service Manual ▷ View online
25
AK - 44
CHASSIS
14.3 Using Coloured Buttons
By using the four coloured buttons on the remote control (24, 23, 13, 14) different features or adjust may be
accessed.
accessed.
Figure 6. Coloured buttons Remote Control
14.3.1 AVL
Press the RED button (23) to activate or deactivate the AVL (Automatic Volume Level, between different broadcast
channels).
Press the RED button (23) to activate or deactivate the AVL (Automatic Volume Level, between different broadcast
channels).
14.3.2 GEOMETRY MENU
Press the GREEN button (24) in order to change from the Main Service Menu to the Geometry Menu, as shows
the figure 7. To return to the Main Service Menu it should be pressed the Menu button (30), see Figure 5.
Press the GREEN button (24) in order to change from the Main Service Menu to the Geometry Menu, as shows
the figure 7. To return to the Main Service Menu it should be pressed the Menu button (30), see Figure 5.
Figure 7. Geometry Menu
Figure 8. Remote Control
In the bottom area of this Menu, it can be seen “AUTO”. By pressing the WIDE MODE button (8) it changes to 4:3
or 16:9 format. To perform the Geometry adjustments select the most suitable option:
or 16:9 format. To perform the Geometry adjustments select the most suitable option:
- AUTO, entering 4:3 or 16:9 signal and proceeding with adjustments as below.
- 4:3, entering 4:3 signal and proceeding with adjustments as below.
- 16:9, entering 16:9 signal and proceeding with adjustments as below.
- 4:3, entering 4:3 signal and proceeding with adjustments as below.
- 16:9, entering 16:9 signal and proceeding with adjustments as below.
26
AK - 44
CHASSIS
14.3.2.1 Geometry Table
Default Values
A51EFS13X191
A51ELD032X001
Register
Parameter
4:3
16:9
4:3
16:9
VSIZ
Vertical Size
35 62 24 50
VPO S
Vertical Position
11 16 12 16
VSCO
Not used
14 14 14 14
VCCO
Not used
7 7 7 7
HSIZ
Not used
10 9 30 11
HPOS
Horizontal Position
33 33 40 39
HPIN
Not used
19 15 27 15
HCCO
Not used
0 0 0 0
HTRP
Not used
10 10 3 10
VZSZ
Not used
3 2 7 2
14.3.2.2 Geometry Adjustments
VSIX (Vertical Size)
Adjust the Vertical Size so that 8% over-scan is achieved.
The effect of this adjustment is shown in figure 9.
The effect of this adjustment is shown in figure 9.
•
Use the CURSOR LEFT (32) / RIGHT (3) buttons to change the data.
See figure 5.
Figure 9
VPOS (Vertical Position)
Adjust the Vertical Position so that the picture is centred.
The effect of this adjustment is shown in figure 10.
The effect of this adjustment is shown in figure 10.
•
Use the CURSOR LEFT (32) / RIGHT (3) buttons to change the data.
See figure 5.
Figure 10
HPOS (Horizontal Position)
Adjust the Horizontal Position so that the picture is centred.
The effect of this adjustment is shown in figure 11.
The effect of this adjustment is shown in figure 11.
•
Use the CURSOR LEFT (32) / RIGHT (3) buttons to change the data.
See figure 5
.
Figure 11
.
14.3.3 Screen Adjustment
Press the YELLOW button (13) in order to prepare the system for screen-adjustments (Vertical Scan disable).
Adjust horizontal line, via screen potentiometer, as thin as possible. To return to the Main Service Menu it should
be pressed the Menu button (30).
Press the YELLOW button (13) in order to prepare the system for screen-adjustments (Vertical Scan disable).
Adjust horizontal line, via screen potentiometer, as thin as possible. To return to the Main Service Menu it should
be pressed the Menu button (30).
27
AK - 44
CHASSIS
14.3.4 IF Adjustment
Select IF1, IF2, IF3 or IF4. When the blue button (14) is pressed the before selected IF register is automatically
adjusted.
adjusted.
14.4 Auto Programming System Set Up
1. Description
In case the TV set should be serviced, there is the possibility of returning the set with the A.P.S. (Auto Programming
System) activated in order to make easy the first start up to the customer. See the below figure.
If this Feature is activated the Picture and Sound Menus will be automatically memorized to the default values.
System) activated in order to make easy the first start up to the customer. See the below figure.
If this Feature is activated the Picture and Sound Menus will be automatically memorized to the default values.
2. Before start
It is necessary let the TV set in the program number that will appear for the first time, because the A.P.S does not
preset this selection.
preset this selection.
3. Procedure
3.1 Enter the Service Mode. See Page 23.
3.2 Access to TXT1 Register by CURSOR UP / DOWN.
3.3 Press 7 button on the remote control in order to activate the Auto Programming System.
3.4 Exit the Service Mode by the Menu button (30).
3.5 Switch the TV off using the mains switch.
3.2 Access to TXT1 Register by CURSOR UP / DOWN.
3.3 Press 7 button on the remote control in order to activate the Auto Programming System.
3.4 Exit the Service Mode by the Menu button (30).
3.5 Switch the TV off using the mains switch.
15. OPTION LIST
15.1 Service Registers Updating regarding the Tuner
AK30 PLL TUNER SETTINGS
VHF1-VHF3 VHF3-UHF
Frq. (Mhz)
Frq. (Mhz)
Frq. (Mhz)
F1H
F1L
F2H
F2L
BS1
BS2
BS3
CB
Philips UV1316S MK3
156,25 MHz 441,25 MHz
00001100
00110010
00011110
00000010
00000001
00000010
00000100
10001110
Thomson CTT5020
114,25 MHz 401,25 MHz
00001001
10010010
00011011
10000010
00000011
00000110
10000101
10001110
Samsung TECC2949PG28B
170,25 MHz 465,25 MHz
00001101
00010010
00011111
10000010
00000001
00000010
00000100
10001110
Samsung TECC2949PG35B
170,25 MHz 449,25 MHz
00001101
00010010
00011110
10000010
00000001
00000010
00001000
10001110
Alps TEDE9X226A
142,25 MHz 425,25 MHz
00001011
01010010
00011101
00000010
00000001
00000010
00001000
10001110
Alps TEDE9-004A
149,25 MHz 424,25 MHz
00001011
11000010
00011100
11110010
00000001
00000010
00001000
10001110
AK44 SERVICE MENU ITEMS
F1H
High byte of VHF1-VHF3 cross-over frequency
F1L
Low byte of VHF1-VHF3 cross-over frequency
F2H
High byte of VHF3-UHF cross-over frequency
F2L
Low byte of VHF3-UHF cross-over frequency
BS1
Band switching byte for VHF1
BS2
Band switching byte for VHF3
BS3
Band switching byte for UHF
CB
Control byte
Explanations
28
AK - 44
CHASSIS
15.2 Registers Details
OP1 – Peripheral Options
7
NOT USED
6 1,
Display
“AV-3”
as
“F-AV”
0, Display “AV-3” as “B-AV”
5 1, Turn back TV mode after the last AV (with AV key)
0, Turn back first AV mode after the last AV
4 1, SVHS is available in AV key stream
0, SVHS is NOT available in AV key stream
3 1, RGB is available in AV key stream
0, RGB is NOT available in AV key stream
2 1, AV-3 is available in AV key stream
0, AV-3 is NOT available in AV key stream
1 1, AV-2 is available in AV key stream
0, AV-2 is NOT available in AV key stream
0 0 1, AV-1 is available in AV key stream
0, AV-1 is NOT available in AV key stream
OP2 – Reception Standard Options
7 1,
3-button
keyboard
(V-,
P+,
V+)
0, 4/5 button keyboard (V-, V+, P-, P+, Menu)
6
1,
L/L’
is
available
0, L/L’ is not available
5
1,
I
is
available
0, I is not available
4
1,
DK
is
available
0, DK is not available
3
1,
BG
is
available
0, BG is not available
2
1 0 RESERVED (Keep as 000)
OP3 – Video Options
7
6 Xtal
Configuration
00, 1 Xtal PAL 4.43
01, 2 Xtal PAL/NTSC 4.43/3.58
10, 1 Xtal PAL/SEC/NTSC 4.43
11, 2 Xtal PAL/SEC/NTSC 4.43/3.58
01, 2 Xtal PAL/NTSC 4.43/3.58
10, 1 Xtal PAL/SEC/NTSC 4.43
11, 2 Xtal PAL/SEC/NTSC 4.43/3.58
5 1, Enable Blue back when no signal in AV modes
0, No blue back in AV modes
4 1, White Insertion is ON
0, White Insertion is OFF
3 1, Blue Background when no signal
0, Disable Blue Background
2 1, Semi-transparent background for menu
0, Solid Menu background for menu
1 1, Black Stretch is ON
0, Black Stretch is OFF
0 1,
APR
is
ON
0, APR is OFF
Click on the first or last page to see other 21LF-90H (serv.man3) service manuals if exist.