Sharp 21KF-80 (serv.man13) Service Manual ▷ View online
25
21KF-80H
AN7523 (IC302, IC303)
Block Diagram
Pin Descriptions
Note: Do not apply voltage or current to NC pin from outside
AN5522 (IC501)
Block Diagram
Pin Descriptions
1
2
3
4
5
6
7
8
9
V
CC
Output
GND
Output
Standby
Input
GND
N.C.
V
olume
Pin No.
Description
1
Vcc
2
Ch Output (+)
3
GND
4
Ch Output (-)
5
Standby
6
Ch Input
7
GND
8
N.C
9
Volume
Pin No.
Pin Name
1
Inverting Input
2
Power Supply
3
Pump-up Output
4
GND
5
Vertical Output
6
Vertical Output Power Supply
7
Non-inverting Input
Non-inverting Input
Output Vcc
Output
GND
Pump Up Out
Vcc
Inverting Input
1
2
3
4
5
6
7
Pump Up
Thermal Protection
Amp
+
-
26
21KF-80H
MSP34x5G (IC3001)
Pinning
Block Diagram
PMQFP44 package
CAPL_M
AHVSS
AGNDC
SC2_IN_L
SC2_IN_R
ASG
SC1_IN_L
SC1_IN_R
VREFTOP
MONO_IN
AVSS
RESETQ
I2S_DA_IN2
DVSS
DVSUP
ADR_CL
I2S_DA_IN1
I2S_DA_OUT
I2S_WS
I2S_CL
I2C_DA
I2C_CL
NC
SC1_OUT_L
SC1_OUT_R
VREF1
NC
AHVSUP
DACM_L
DACM_R
VREF2
NC
NC
ANA_IN1
+
ANA_IN
−
TESTEN
XTAL_IN
XTAL_OUT
AVSUP
TP
D_CTR_I/O1
D_CTR_I/O0
ADR_SEL
STANDBYQ
MSP 34x5G
34
35
36
37
38
39
40
41
42
43
44
22
21
20
19
18
17
16
15
14
13
12
1
2
3
4
5
6
7
8
9
10 11
33 32 31 30 29 28 27 26 25 24 23
Simplified functional block diagram of MSP 34x5G
Sour
ce Select
Loud-
SCART1
SCART1
SCART2
MONO
De-
modulator
speaker
Sound
Processing
DAC
ADC
Loud-
DAC
ADC
Sound IF1
speaker
I
2
S
I
2
S1
I
2
S2
Pre-
processing
Prescale
Prescale
SCART
DSP
Input
Select
SCART
Output
Select
27
21KF-80H
SCHEMATIC DIAGRAMS
Description
Waveforms
Service precaution:
The area enclosed by this line is directly ( )
connected with AC mains voltage.
When servicing the area, connect an insulating
transformer between TV receiver and AC line to
eliminate hazard of electric shock.
The area enclosed by this line is directly ( )
connected with AC mains voltage.
When servicing the area, connect an insulating
transformer between TV receiver and AC line to
eliminate hazard of electric shock.
Waveform measurement condition:
Colour bar generator signal of 70 dB from RF input.
Colour bar generator signal of 70 dB from RF input.
1. The unit of resistance «ohm»is omitted (K=1000 ohms.
M= Megaohm).
2. All resistors are 1/16 watt. unless otherwise noted.
3. All capacitors are
M= Megaohm).
2. All resistors are 1/16 watt. unless otherwise noted.
3. All capacitors are
µF, unless otherwise noted (P= µµF).
4. The capacitor with Part No. RC-FZ9XXXBMNJ is de-
signed to with stand 63V.
5. The capacitor with Part No. RC-FZ4XXXBMNJ is de-
signed to with stand 50V.
signed to with stand 63V.
5. The capacitor with Part No. RC-FZ4XXXBMNJ is de-
signed to with stand 50V.
Note:
CAUTION
This circuit diagram is original one, therefore
there may be slight difference from yours.
This circuit diagram is original one, therefore
there may be slight difference from yours.
Important safety note:
Parts marked with «
» (
) are important
for maintaining the safety of the set. Be sure to re-
place these parts with specified ones for maintain-
ing the safety and performance of the set.
place these parts with specified ones for maintain-
ing the safety and performance of the set.
!
Safety note:
1. Disconnect the AC plug from the AC outlet be-
fore replacing parts.
1. Disconnect the AC plug from the AC outlet be-
fore replacing parts.
2. Semiconductor heat sinks should be regarded
as potential shock hazards when the chassis is
operating.
as potential shock hazards when the chassis is
operating.
28
21KF-80H
Click on the first or last page to see other 21KF-80 (serv.man13) service manuals if exist.