Sharp XV-Z91E (serv.man32) User Manual / Operation Manual ▷ View online
Important
Information
-10
Part Names
Inserting the batteries
1
3
Pull down the tab on the
battery cover and
remove the cover
towards the direction of
the arrow.
battery cover and
remove the cover
towards the direction of
the arrow.
2
Insert two AA size
batteries, making sure
the polarities match the
batteries, making sure
the polarities match the
ⴐ and ⴑ marks inside
the battery compartment.
the battery compartment.
Insert the lower tab of
the battery cover into
the opening, and press
the cover until it clicks
in place.
the battery cover into
the opening, and press
the cover until it clicks
in place.
Top View
Remote Control
LIGHT button
16
24
35
36
19
26
26
26
24
24
24
24
32
15
POWER buttons (ON/OFF)
ENTER button
19
KEYSTONE button
UNDO button
INPUT 1 button
INPUT 2 button
INPUT 4 button
AUTO SYNC button
RESIZE button
PICTURE SETTING button
MENU button
ADJUSTMENT buttons
(∂/ƒ/ß/©)
(∂/ƒ/ß/©)
INPUT 3 button
RGB/COMP. button
Front View
Top View
Remote control signal transmitters
Battery cover
Battery
compartment
Battery
cover
Important
Information
-11
Supplied Accessories
Remote control
Power cord
(For U.K., Hong Kong
and Singapore)
• Use the power cord that corresponds to the wall outlet in your
country.
Computer-RGB
cable
cable
21 pin RCA
conversion adaptor
conversion adaptor
Terminal cover
Lens cap
Video cable
Two AA size batteries
Lens cap strap
(For Australia
and New Zealand)
Projector Operation manual
Screws for terminal cover
(For Europe except U.K.)
Setup & Connections
-12
Power Supply
Connecting the Power Cord
Plug the supplied power cord into the AC socket on the back of the projector.
Connections
Power cord
CAUTION
• Make sure the power cord is firmly connected into the AC socket.
• The projector will enter the standby mode as you re-plug it into the AC socket, when unplugging the power cord after turning the power
off by pressing the POWER button. However, if the projector was turned off by disconnecting the power cord or by a power failure, the
projector will automatically turn on when plugging the power cord again.
projector will automatically turn on when plugging the power cord again.
1 Connect one end of the S-video cable (commercially
available) to the INPUT 3 S-VIDEO terminal, or one end
of the video cable to the INPUT 4 VIDEO terminal on
the projector.
of the video cable to the INPUT 4 VIDEO terminal on
the projector.
2 Connect the other end of the S-video cable or the video
cable to the S-video output or Video output terminal of
the video source.
the video source.
The S-video input terminal uses a video signal system where
the picture is separated into a colour and luminance signal
to realise a higher-quality image.
the picture is separated into a colour and luminance signal
to realise a higher-quality image.
• For higher quality video, you may use the S-video input terminal on the
projector. An S-video cable is commercially available.
• If your video equipment does not have an S-video output terminal, use
the composite video output terminal.
Connecting to Video Equipment
Connecting a video source (VCR, laser disc player, DVD player or DTV decoder) using the INPUT 3
S-VIDEO and INPUT 4 VIDEO terminals
S-VIDEO and INPUT 4 VIDEO terminals
You can connect your projector to a VCR, laser disc player, DVD player, DTV* decoder and other video equipment.
* DTV is the umbrella term used to describe the new digital television system in the United States.
CAUTION
• Make sure to turn both the projector and the video equipment off, before connecting.
• As this projector is not equipped with audio input terminals, commercially available audio equipment or your own equipment (such as
speakers or amplifiers) should be used.
-13
Setup & Connections
1
2 To S-video output terminal
2 To video output terminal
1
Projector
VCR, Laser disc player,
DVD player or DTV decoder
Connecting to Video Equipment
Connecting to a DVD Player and DTV Decoder
2 To component output
terminals
1
Component cable
(commercially available)
(commercially available)
DVD player
or
DTV decoder
1 Connect each RCA connector of a component cable to the corresponding
RCA INPUT 1 terminals on the projector.
2 Connect the other end of the cable to the corresponding terminals on a DVD
player or DTV decoder.
CAUTION
• Make sure to turn both the projector and the video equipment off, before
connecting.
S-video cable (commercially available)
Video cable
Projector
Connecting to a DVD player and DTV decoder with Component output (for INPUT 1)
Connecting to a DVD player and DTV decoder with component output (for INPUT 2)
1 Connect the 3 RCA to 15-pin D-Sub cable to INPUT 2 COMPONENT/RGB port on the projector.
2 Use the above cables to connect the DTV decoder or DVD player.
2 Use the above cables to connect the DTV decoder or DVD player.
When connecting this projector to analog RGB output of the DTV decoder, select “Component” for “Signal Type” on the
OSD menu or press RGB/COMP. on the remote control. (See page 36.)
OSD menu or press RGB/COMP. on the remote control. (See page 36.)
CAUTION
• Make sure to turn both the projector and the video equipment off, before connecting.
Projector
3 RCA to 15-pin D-sub cable
(sold separately AN-C3CP)
(sold separately AN-C3CP)
DVD player
or
DTV decoder
1
2
Click on the first or last page to see other XV-Z91E (serv.man32) service manuals if exist.